Mersedes Maybach S-Class. Service Manual — part 18
Display messages
Possible causes/consequences and M Solutions
4
Check Engine Oil At
Next Refueling
The engine oil level has dropped to the minimum level.
A warning tone also sounds.
!
Avoid long journeys with too little engine oil. The engine will oth-
erwise be damaged.
X
Check the oil level when next refueling, at the latest (
Y
page 353).
X
If necessary, add engine oil (
Y
page 355).
If the engine oil needs topping up more often:
X
Contact a qualified specialist workshop and have the engine
checked.
Information on approved engine oils can be obtained from any quali-
fied specialist workshop or on the Internet at http://bevo.mercedes-
benz.com.
4
Check Engine Oil
Level (Add 1 quart)
The engine oil level has dropped to the minimum level.
!
Avoid long journeys with too little engine oil. The engine will oth-
erwise be damaged.
X
Check the oil level when next refueling, at the latest (
Y
page 353).
X
If necessary, add engine oil (
Y
page 355).
If the engine oil needs topping up more often:
X
Contact a qualified specialist workshop and have the engine
checked.
Information on approved engine oils can be obtained from any quali-
fied specialist workshop or on the Internet at http://bevo.mercedes-
benz.com.
4
Engine Oil Level
Low Stop Vehicle
Turn Engine Off
The engine oil level is too low. There is a risk of engine damage.
X
Pull over and stop the vehicle safely and switch off the engine, pay-
ing attention to road and traffic conditions.
X
Secure the vehicle against rolling away (
Y
page 189).
X
Check the engine oil level (
Y
page 353).
X
If necessary, add engine oil (
Y
page 355).
8
Fuel Level Low
The fuel level has dropped into the reserve range.
X
Refuel at the nearest gas station.
C
There is only a very small amount of fuel in the fuel tank.
X
Refuel at the nearest gas station without fail.
8
Gas Cap Loose
The fuel filler cap is not closed correctly or the fuel system is leaking.
X
Check that the fuel filler cap is correctly closed.
If the fuel filler cap is not correctly closed:
X
Close the fuel filler cap.
If the fuel filler cap is correctly closed:
X
Visit a qualified specialist workshop.
296
Display messages
O
n-board
com
puter
and
di
spla
ys
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Hybrid drive system
Display messages
Possible causes/consequences and M Solutions
d
Vehicle Operational
Switch the Ignition
Off Before Exiting
PLUG-IN HYBRID vehicles:
You are leaving the vehicle when it is in a ready-to-drive state. The
READY indicator in the multifunction display is on. A warning tone also
sounds.
If you leave the vehicle:
X
Secure the vehicle against rolling away (
Y
page 189).
X
Switch off the ignition and remove the SmartKey.
If you do not leave the vehicle:
X
Switch off the electrical consumers, e.g. automatic climate control,
seat heating.
Please note the following: the electrical consumers are supplied by the
12 V battery. If the vehicle is left in a ready-to-drive state for an exten-
ded period, it will switch off once the 12 V battery is almost empty. It
will then only be possible to start the vehicle using a second battery
(jump-starting).
Change the current
drive program
before changing the
operating mode.
or
Exit manual drive
program M before
changing the operat‐
ing mode.
PLUG-IN HYBRID vehicles:
You have attempted to change the operating mode when in automatic
drive program S (Sport) or manual drive program M.
X
Activate the drive program E (Economy) or E+ (Economy Plus)
(
Y
page 250).
X
Select the preferred operating mode HYBRID, E-MODE, E-SAVE or
CHARGE (
Y
page 243).
E-MODE Currently
Unavailable
PLUG-IN HYBRID vehicles:
The condition of charge of the high-voltage battery has dropped to the
lower limit and the E-MODE operating mode has been switched off.
Driving with the internal combustion engine is activated and the oper-
ating mode switches to the basic HYBRID setting.
X
Continue driving using the internal combustion engine.
You can switch to the E-SAVE or CHARGE operating mode as
required (
Y
page 243).
If you select CHARGE, the high-voltage battery is charged.
Once the charge level display for the high-voltage battery has
increased slightly, you can switch to the E-MODE operating mode
again.
Display messages
297
On-board
comput
er
and
displays
Z
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Display messages
Possible causes/consequences and M Solutions
Only E-MODE Availa‐
ble Power Limited
Refuel Immediately
PLUG-IN HYBRID vehicles:
The fuel tank has been run dry and the combustion engine has been
switched off.
A warning tone also sounds.
The vehicle will be powered by electrical energy only. Performance is
restricted and the vehicle may accelerate more slowly than normal.
X
Refuel at the nearest gas station without fail.
In the "Total range and electric range" menu, you can display the
approximate range of the vehicle (
Y
page 248).
Engine will not
restart Service
required
You cannot start the engine again due to a malfunction.
A warning tone also sounds.
If the engine is running:
X
Visit a qualified specialist workshop.
If you switch off the engine:
X
Secure the vehicle against rolling away (
Y
page 189).
X
Notify a qualified specialist workshop or breakdown service.
á
Towing Not Permit‐
ted See Operator's
Manual
The hybrid drive system is faulty.
X
Have the vehicle transported on a transporter or trailer to the near-
est qualified specialist workshop.
Û
Malfunction Service
Required
The hybrid drive system is faulty.
X
Visit a qualified specialist workshop.
Û
Malfunction
The hybrid drive system is faulty.
X
Have the vehicle towed away by a professional recovery company to
the nearest qualified specialist workshop.
d
Malfunction
The hybrid drive system is faulty.
The ECO start/stop function may be malfunctioning.
The drive power is restricted.
X
Visit a qualified specialist workshop.
ï
Charger Cable Con‐
nected
PLUG-IN HYBRID vehicles:
The charging cable connector is connected to the vehicle socket.
You cannot drive off as long as the charging cable connector is still
connected.
Before you drive off:
X
Remove the charging cable connector from the vehicle socket
(
Y
page 185).
298
Display messages
O
n-board
com
puter
and
di
spla
ys
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Display messages
Possible causes/consequences and M Solutions
6
Please Wait
Depressurizing Tank
PLUG-IN HYBRID vehicles:
The fuel filler flap unlocking button has been pulled. The fuel tank must
be depressurized before refueling.
X
Wait until the fuel tank is depressurized and the fuel filler flap is
unlocked.
The opening process for the fuel filler cap may take up to 15
minutes.
6
Tank is Depressur‐
ized Ready for Refu‐
eling
PLUG-IN HYBRID vehicles:
The fuel tank is now depressurized. The vehicle may now be refueled.
X
Observe the information on refueling on the fuel filler flap.
X
Open the fuel filler cap and remove it (
Y
page 179).
6
Tank Ventilation
Malfunction Service
Required
PLUG-IN HYBRID vehicles:
There is a malfunction in the fuel system.
X
Visit a qualified specialist workshop.
ã
Acoustic Vehicle
Indication Inopera‐
tive
PLUG-IN HYBRID vehicles:
The sound generator is not working. The vehicle can still be driven;
however, no vehicle sounds can be generated. As a result, your vehicle
may not be heard by other road users until it is very close to them, or
it may not be heard at all.
X
Drive with particular care, allowing for the possibility that other road
users may behave unpredictably.
X
Visit a qualified specialist workshop.
Driving systems
Display messages
Possible causes/consequences and M Solutions
À
ATTENTION ASSIST:
Take a Break!
Based on certain criteria, ATTENTION ASSIST has detected fatigue or
a lack of concentration on the part of the driver. A warning tone also
sounds.
X
If necessary, take a break.
During long journeys, take regular breaks in good time so you get
enough rest.
À
ATTENTION ASSIST
Inoperative
ATTENTION ASSIST is inoperative.
X
Visit a qualified specialist workshop.
¨
Vehicle Rising
Your vehicle is adjusting to the level you have selected.
Display messages
299
O
n-board
com
puter
and
di
spla
ys
Z
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Display messages
Possible causes/consequences and M Solutions
¨
Vehicle Rising
Please Wait
The vehicle level is too low when the vehicle is stationary. A warning
tone also sounds.
X
Do not pull away.
The vehicle level is set when the display message disappears.
¨
Stop Vehicle Vehi‐
cle Too Low
You have pulled away while the vehicle level is still too low.
AIRMATIC sets the vehicle to the selected level after a short period.
X
Pull over and stop the vehicle safely as soon as possible, paying
attention to road and traffic conditions.
X
Secure the vehicle against rolling away (
Y
page 189).
X
Wait until the display message disappears before pulling away.
AIRMATIC is defective. A warning tone also sounds.
X
Do not drive at speeds above 50 mph (80 km/h).
X
Make only slight steering movements. Otherwise, the front fender
or the tires could be damaged if the steering movement is too large.
X
Listen for scraping sounds.
X
Pull over and stop the vehicle safely, paying attention to road and
traffic conditions, and set a higher vehicle level.
Depending on the malfunction, it may be possible to raise the vehi-
cle.
X
Visit a qualified specialist workshop.
¨
Malfunction
The AIRMATIC function is restricted. The vehicle's handling charac-
teristics may be affected.
X
Do not drive at speeds above 50 mph (80 km/h).
X
Visit a qualified specialist workshop.
ABC Malfunction
Stop Vehicle
The Active Body Control (ABC) vehicle level is too low.
X
Pull over and stop the vehicle safely as soon as possible, paying
attention to road and traffic conditions.
After a few seconds, the vehicle level is adjusted and the display
message disappears.
The multifunction display continuously shows the display message.
The vehicle is leaking oil.
X
Pull over and stop the vehicle safely as soon as possible, paying
attention to road and traffic conditions. Do not continue driving
under any circumstances.
X
Consult a qualified specialist workshop.
The multifunction display continuously shows the display message.
Active Body Control (ABC) is malfunctioning.
X
Do not drive at speeds above 50 mph (80 km/h).
X
Make only slight steering movements. Otherwise, the front fender
or the tires could be damaged if the steering movement is too large.
X
Listen for scraping sounds.
X
Visit a qualified specialist workshop.
300
Display messages
O
n-board
com
puter
and
di
spla
ys
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Display messages
Possible causes/consequences and M Solutions
ABC Vehicle Rising
Please Wait Briefly
The vehicle level is too low when the vehicle is stationary. A warning
tone also sounds.
X
Do not pull away.
The vehicle level is set when the display message disappears.
ABC Malfunction
The Active Body Control (ABC) function is restricted. The vehicle's
handling characteristics may be affected.
X
Do not drive at speeds above 50 mph (80 km/h).
X
Visit a qualified specialist workshop.
Active Lane Keeping
Assist Currently
Unavailable See
Operator's Manual
Active Lane Keeping Assist is deactivated and temporarily inoperative.
Possible causes are:
R
the windshield in the camera's field of vision is dirty.
R
visibility is impaired due to heavy rain, snow or fog.
R
there have been no lane markings for an extended period.
R
the lane markings are worn, dark or covered, e.g. by dirt or snow.
When the causes stated above no longer apply, the display message
disappears.
Active Lane Keeping Assist is operational again.
If the display message does not disappear:
X
Pull over and stop the vehicle safely as soon as possible, paying
attention to road and traffic conditions.
X
Secure the vehicle against rolling away (
Y
page 189).
X
Clean the windshield.
Active Lane Keeping
Assist Inoperative
Active Lane Keeping Assist is defective.
X
Visit a qualified specialist workshop.
Active Blind Spot
Assist Currently
Unavailable See
Operator's Manual
Active Blind Spot Assist is temporarily inoperative.
Possible causes are:
R
the radar sensor system is outside the operating temperature
range.
R
the radar sensor system is temporarily inoperative, e.g. due to elec-
tromagnetic radiation emitted by nearby TV or radio stations or
other sources of electromagnetic radiation.
When the causes stated above no longer apply, the display message
disappears.
Active Blind Spot Assist is operational again.
If the display message does not disappear:
X
Pull over and stop the vehicle safely as soon as possible, paying
attention to road and traffic conditions.
X
Secure the vehicle against rolling away (
Y
page 189).
X
Restart the engine.
Active Blind Spot
Assist Inoperative
Active Blind Spot Assist is defective.
X
Visit a qualified specialist workshop.
Display messages
301
O
n-board
com
puter
and
di
spla
ys
Z
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Display messages
Possible causes/consequences and M Solutions
Park Assist Canceled
The driver's door is open.
X
Repeat the parking gap measurement and parking process with the
driver's door closed.
You touched the multifunction steering wheel while steering inter-
vention was active.
X
While steering intervention is active, make sure that the multifunc-
tion steering wheel is not touched unintentionally.
The vehicle has started to skid and ESP
®
has intervened.
X
Use Active Parking Assist again later (
Y
page 216).
Park Assist Inoper‐
ative
PARKTRONIC is malfunctioning or faulty.
X
Follow the instructions and helpful hints in the "Problems with
PARKTRONIC" section (
Y
page 216).
If the multifunction display still shows the display message:
X
Visit a qualified specialist workshop.
Active Parking Assist is unavailable or faulty.
X
Switch off the ignition and restart the engine.
If Active Parking Assist continues to be unavailable (the j symbol is
not shown in the multifunction display):
X
Visit a qualified specialist workshop.
Park Assist
Switched Off
The vehicle is parked. A warning tone also sounds.
The display message disappears automatically.
Night View Assist
Currently Unavaila‐
ble
Night View Assist Plus is deactivated and temporarily inoperative.
Possible causes are:
R
the windshield in the camera's field of vision is dirty.
R
the camera in the radiator trim is dirty.
R
visibility is impaired due to heavy rain, snow or fog.
R
the outside temperature is too high.
X
Clean the windshield.
X
Clean the camera in the radiator trim.
If the system has been switched off due to excessive outside tem-
peratures, the system will switch back on automatically once it has
cooled down.
If the system detects that the camera is fully operational, the display
message disappears.
Night View Assist Plus is operational again.
Night View Assist
Inoperative
Night View Assist Plus is defective.
X
Visit a qualified specialist workshop.
302
Display messages
O
n-board
com
puter
and
di
spla
ys
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Display messages
Possible causes/consequences and M Solutions
Spotlight Inopera‐
tive
Night View Assist Plus is deactivated and temporarily inoperative.
Possible causes are:
R
the windshield in the camera's field of vision is dirty.
R
the camera in the radiator trim is dirty.
R
visibility is impaired due to heavy rain, snow or fog.
R
the outside temperature is too high.
X
Clean the windshield.
X
Clean the camera in the radiator trim.
If the system has been switched off due to excessive outside tem-
peratures, the system will switch back on automatically once it has
cooled down.
If the system detects that the camera is fully operational, the display
message disappears.
Night View Assist Plus is operational again.
Night View Assist Plus is faulty.
X
Visit a qualified specialist workshop.
Traffic Sign Assist
Currently Unavaila‐
ble See Operator's
Manual
Traffic Sign Assist is temporarily inoperative.
Possible causes are:
R
the windshield in the camera's field of vision is dirty.
R
visibility is impaired due to heavy rain, snow or fog.
X
Clean the windshield.
If the system detects that the camera is fully operational, the display
message disappears.
Traffic Sign Assist is operational again.
Traffic Sign Assist
Inoperative
Traffic Sign Assist is faulty.
X
Visit a qualified specialist workshop.
ë
Off
The HOLD function is deactivated. The vehicle is skidding.
A warning tone also sounds.
X
Reactivate the HOLD function later (
Y
page 208).
DISTRONIC PLUS Off
DISTRONIC PLUS has been deactivated.
If a warning tone also sounds, DISTRONIC PLUS has deactivated auto-
matically (
Y
page 199).
DISTRONIC PLUS Now
Available
DISTRONIC PLUS is operational again after having been temporarily
unavailable. You can now reactivate DISTRONIC PLUS (
Y
page 199).
Display messages
303
O
n-board
com
puter
and
di
spla
ys
Z
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Display messages
Possible causes/consequences and M Solutions
DISTRONIC PLUS Cur‐
rently Unavailable
See Operator's Man‐
ual
DISTRONIC PLUS is temporarily inoperative.
Steering Assist and Stop&Go Pilot are temporarily inoperative.
Possible causes are:
R
the radar sensor system is temporarily inoperative, e.g. due to elec-
tromagnetic radiation emitted by nearby TV or radio stations or
other sources of electromagnetic radiation.
R
the system is outside the operating temperature range.
R
the on-board voltage is too low.
A warning tone also sounds.
When the causes stated above no longer apply, the display message
disappears.
DISTRONIC PLUS is operational again.
If the display message does not disappear:
X
Pull over and stop the vehicle safely as soon as possible, paying
attention to road and traffic conditions.
X
Secure the vehicle against rolling away (
Y
page 189).
X
Restart the engine.
DISTRONIC PLUS Inop‐
erative
DISTRONIC PLUS is defective.
The following may have also failed:
R
BAS PLUS with Cross-Traffic Assist
R
PRE-SAFE
®
Brake
R
Steering Assist and Stop&Go Pilot
A warning tone also sounds.
X
Visit a qualified specialist workshop.
DISTRONIC PLUS Sus‐
pended
You have depressed the accelerator pedal. DISTRONIC PLUS is no
longer controlling the speed of the vehicle.
X
Remove your foot from the accelerator pedal.
DISTRONIC PLUS
- - - mph
An activation condition for DISTRONIC PLUS is not fulfilled.
X
Check the activation conditions for DISTRONIC PLUS (
Y
page 199).
304
Display messages
O
n-board
com
puter
and
di
spla
ys
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Display messages
Possible causes/consequences and M Solutions
DTR+: Steering
Assist. Currently
Unavailable See
Operator's Manual
Steering Assist and Stop&Go Pilot are temporarily inoperative.
Possible causes are:
R
the windshield in the camera's field of vision is dirty.
R
visibility is impaired due to heavy rain, snow or fog.
R
there have been no lane markings for an extended period.
R
the lane markings are worn, dark or covered, e.g. by dirt or snow.
When the causes stated above no longer apply, the display message
disappears.
Steering Assist and Stop&Go Pilot are operative again.
If the display message does not disappear:
X
Pull over and stop the vehicle safely as soon as possible, paying
attention to road and traffic conditions.
X
Secure the vehicle against rolling away (
Y
page 189).
X
Clean the windshield.
DTR+: Steering
Assist. Inoperative
Steering Assist and Stop&Go Pilot are faulty.
However, the DISTRONIC PLUS functions are still available.
A warning tone also sounds.
X
Visit a qualified specialist workshop.
Cruise Control Inop‐
erative
Cruise control is malfunctioning.
A warning tone also sounds.
X
Visit a qualified specialist workshop.
Cruise Control
- - - mph
R
A condition for activating cruise control has not been met.
You have tried to store a speed below 20 mph (30 km/h), for exam-
ple.
R
ESP
®
is deactivated. The yellow ESP
®
OFF warning lamp is lit.
X
If conditions permit, drive faster than 20 mph (30 km/h) and store
the speed.
or
X
Check the activation conditions for cruise control (
Y
page 197).
or
X
Reactivate ESP
®
(
Y
page 269).
Cruise Control Off
Cruise control has been deactivated.
If a warning tone also sounds, cruise control has deactivated auto-
matically (
Y
page 197).
Display messages
305
O
n-board
com
puter
and
di
spla
ys
Z
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Tires
Display messages
Possible causes/consequences and M Solutions
Check Tire Pressure
Soon
Canada only:
The tire pressure loss warning system has detected a significant loss
in pressure.
A warning tone also sounds.
Possible causes:
R
you have changed the positions of the wheels and tires or installed
new wheels and tires.
R
the tire pressure in one or more tires has dropped
G
WARNING
Tire pressures that are too low pose the following hazards:
R
they may burst, especially as the load and vehicle speed increase.
R
they may wear excessively and/or unevenly, which may greatly
impair tire traction.
R
the driving characteristics, as well as steering and braking, may be
greatly impaired.
There is a risk of an accident.
X
Stop the vehicle without making any sudden steering or braking
maneuvers. Pay attention to the traffic conditions as you do so.
X
Secure the vehicle against rolling away (
Y
page 189).
X
Check the tires and, if necessary, follow the instructions for a flat
tire (
Y
page 367).
X
Check the tire pressures and, if necessary, correct the tire pressure.
X
Restart the tire pressure loss warning system when the tire pres-
sure is correct (
Y
page 394).
Check Tire Pressure
Then Restart Run
Flat Indicator
Canada only:
The tire pressure loss warning system generated a display message
and has not been restarted since.
X
Set the correct tire pressure in all four tires.
X
Restart the tire pressure loss warning system (
Y
page 394).
Run Flat Indicator
Inoperative
Canada only:
The tire pressure loss warning system is faulty.
X
Visit a qualified specialist workshop.
Please Correct Tire
Pressure
The tire pressure is too low in at least one of the tires, or the tire
pressure difference between the wheels is too great.
X
Check the tire pressures at the next opportunity (
Y
page 390).
X
If necessary, correct the tire pressure.
X
Restart the tire pressure monitor (
Y
page 392).
306
Display messages
O
n-board
com
puter
and
di
spla
ys
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Display messages
Possible causes/consequences and M Solutions
Check Tires
The tire pressure in one or more tires has dropped significantly. The
wheel position is shown in the multifunction display.
A warning tone also sounds.
G
WARNING
Tire pressures that are too low pose the following hazards:
R
they may burst, especially as the load and vehicle speed increase.
R
they may wear excessively and/or unevenly, which may greatly
impair tire traction.
R
the driving characteristics, as well as steering and braking, may be
greatly impaired.
There is a risk of an accident.
X
Stop the vehicle without making any sudden steering or braking
maneuvers. Pay attention to the traffic conditions as you do so.
X
Secure the vehicle against rolling away (
Y
page 189).
X
Check the tires and, if necessary, follow the instructions for a flat
tire (
Y
page 367).
X
Check the tire pressure (
Y
page 390).
X
If necessary, correct the tire pressure.
Warning Tire Mal‐
function
The tire pressure in one or more tires has dropped suddenly. The wheel
position is shown in the multifunction display.
G
WARNING
Driving with a flat tire poses a risk of the following hazards:
R
a flat tire affects the ability to steer or brake the vehicle.
R
you could lose control of the vehicle.
R
continued driving with a flat tire will cause excessive heat build-up
and possibly a fire.
There is a risk of an accident.
X
Stop the vehicle without making any sudden steering or braking
maneuvers. Pay attention to the traffic conditions as you do so.
X
Secure the vehicle against rolling away (
Y
page 189).
X
Check the tires and, if necessary, follow the instructions for a flat
tire (
Y
page 367).
Tire Press. Monitor
Currently Unavaila‐
ble
Because there is interference from a strong source of radio waves, no
signals from the tire pressure sensors are detected. The tire pressure
monitor is temporarily malfunctioning.
X
Drive on.
The tire pressure monitor restarts automatically as soon as the
problem has been resolved.
TirePress. Sen‐
sor(s) Missing
There is no signal from the tire pressure sensor of one or several
wheels. The pressure of the affected tire is not displayed in the mul-
tifunction display.
X
Have the faulty tire pressure sensor replaced at a qualified special-
ist workshop.
Display messages
307
O
n-board
com
puter
and
di
spla
ys
Z
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Display messages
Possible causes/consequences and M Solutions
Tire Pressure Moni‐
tor Inoperative No
Wheel Sensors
The wheels mounted do not have a suitable tire pressure sensor. The
tire pressure monitor is deactivated.
X
Mount wheels with suitable tire pressure sensors.
The tire pressure monitor is activated automatically after driving for
a few minutes.
Tire Press. Monitor
Inoperative
The tire pressure monitor is faulty.
X
Visit a qualified specialist workshop.
Vehicle
Display messages
Possible causes/consequences and M Solutions
Shift to 'P' or 'N'
to Start Engine
You have attempted to start the engine with the transmission in posi-
tion R or D.
X
Shift the transmission to position P or N.
Apply Brake to
Shift from 'P'
You have attempted to move the transmission selector lever to posi-
tion D, R or N without depressing the brake pedal.
X
Depress the brake pedal.
To Deselect P or N,
Depress Brake and
Start Engine
With the engine switched off, you have attempted to shift the trans-
mission out of position P or N into another transmission position.
X
Depress the brake pedal.
X
Start the engine.
Transmission Not in
P Risk of Vehicle
Rolling Away
The driver's door is open or not fully closed and the transmission is in
position R, N or D.
A warning tone also sounds.
G
WARNING
The vehicle may roll away.
There is a risk of an accident.
X
Shift the transmission to position P.
X
Secure the vehicle against rolling away (
Y
page 189).
X
Close the driver's door completely.
Only Shift to 'P'
when Vehicle is Sta‐
tionary
The vehicle is moving.
X
Pull over and stop the vehicle safely as soon as possible, paying
attention to road and traffic conditions.
X
Shift the transmission to position P.
308
Display messages
O
n-board
com
puter
and
di
spla
ys
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Display messages
Possible causes/consequences and M Solutions
Service Required Do
Not Shift Gears
Visit Dealer
You cannot change the transmission position due to a malfunction.
A warning tone also sounds.
If transmission position D is selected:
X
Drive to a qualified specialist workshop without shifting the trans-
mission from position D.
If transmission position R, N or P is selected:
X
Secure the vehicle against rolling away (
Y
page 189).
X
Notify a qualified specialist workshop or breakdown service.
Reversing Not Possi‐
ble Service Required
You cannot shift into the transmission position R due to a malfunction.
The transmission positions P, N or D continue to be available.
A warning tone also sounds.
X
Visit a qualified specialist workshop.
Transmission Mal‐
function Stop
A malfunction has occurred in the mechanical transmission compo-
nents.
A warning tone also sounds. The gearbox automatically shifts to posi-
tion N.
X
Pull over and stop the vehicle safely as soon as possible, paying
attention to road and traffic conditions.
X
Shift the transmission to position P.
X
Secure the vehicle against rolling away (
Y
page 189).
X
Notify a qualified specialist workshop or breakdown service.
Stop Vehicle Leave
Engine Running Wait
Transmission Cool‐
ing
PLUG-IN HYBRID vehicles:
The transmission has overheated. Pulling away can be temporarily
impaired or not possible.
X
Pull over and stop the vehicle safely as soon as possible, paying
attention to road and traffic conditions. Do not continue driving
under any circumstances.
X
Wait until the display message disappears before pulling away.
Auxiliary Battery
Malfunction
The auxiliary battery for the transmission is no longer being charged.
X
Visit a qualified specialist workshop.
X
Until then, set the transmission to position P before you switch off
the engine.
X
Before leaving the vehicle, apply the electric parking brake.
N
The trunk lid is open.
X
Close the trunk lid.
Display messages
309
O
n-board
com
puter
and
di
spla
ys
Z
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Display messages
Possible causes/consequences and M Solutions
M
The hood is open. A warning tone also sounds.
G
WARNING
The open hood may block your view when the vehicle is in motion.
There is a risk of an accident.
X
Pull over and stop the vehicle safely as soon as possible, paying
attention to road and traffic conditions.
X
Secure the vehicle against rolling away (
Y
page 189).
X
Close the hood.
C
At least one door is open. A warning tone also sounds.
X
Close all the doors.
To view the ext.
mirror, adjust
front-passenger
seat or remove the
head restraint.
The front-passenger seat is in the chauffeur mode position and the
head restraint is folded down.
G
WARNING
If the front-passenger seat is the chauffeur mode position and the
head restraint is folded down, the view of the front-passenger exterior
mirror can be impaired.
There is a risk of an accident.
X
Remove the head restraint on the front-passenger seat
(
Y
page 113).
or
X
Move the front-passenger seat back into the normal position
(
Y
page 111).
Front-Passenger
Seat Cannot Be Used
Visit Workshop
R
The front-passenger seat cannot be moved from the chauffeur
mode position into the normal position. There is a malfunction.
R
The front passenger head restraint is folded down and can no longer
be folded up. There is a malfunction.
G
WARNING
If head restraints are not adjusted correctly, they cannot provide pro-
tection as intended.
There is an increased risk of injury in the head and neck area, e.g. in
the event of an accident or when braking.
X
Do not use the front-passenger seat.
X
Visit a qualified specialist workshop immediately.
n
Before oper. front-
pass. seat from
rear, deactiv. over‐
ride feature.
You have attempted to adjust the front-passenger seat from the rear
compartment while the override feature is activated.
X
Deactivate the override feature for the rear side windows
(
Y
page 67).
X
Adjust the front-passenger seat from the rear (
Y
page 108).
310
Display messages
O
n-board
com
puter
and
di
spla
ys
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Display messages
Possible causes/consequences and M Solutions
&
Pre-Entry Climate
Ctrl. (Via Smart‐
Key) Available
Again After Engine
Start
PLUG-IN HYBRID vehicles:
With the engine switched off, you have attempted to switch on the pre-
entry climate control more than twice.
X
Let the engine run for ten seconds.
After running the engine, the pre-entry climate control is opera-
tional again.
&
Pre-Entry Climate
Ctrl. (Via Smart‐
Key) Inoperative HV
Battery Low
PLUG-IN HYBRID vehicles:
The on-board voltage is too low. The pre-entry climate control cannot
be switched on.
X
Drive for a longer distance.
The battery is being charged. When the condition of charge of the
high-voltage battery is over the specified minimum, pre-entry cli-
mate control is operational again.
Ð
Power Steering Mal‐
function See Opera‐
tor's Manual
The power steering is malfunctioning.
A warning tone also sounds.
G
WARNING
You will need to use more force to steer.
There is a risk of an accident.
X
Check whether you are able to apply the extra force required.
If you are able to steer safely:
X
Drive on carefully.
X
Visit a qualified specialist workshop immediately.
If you are unable to steer safely:
X
Do not drive on.
X
Consult a qualified specialist workshop.
Phone No Service
Your vehicle is outside the network provider's transmitter/receiver
range.
X
Wait until the mobile phone operational readiness symbol appears
in the multifunction display.
¥
Check Washer Fluid
The washer fluid level in the washer fluid reservoir has dropped below
the minimum.
X
Add washer fluid (
Y
page 357).
Display messages
311
O
n-board
com
puter
and
di
spla
ys
Z
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст