Great Wall Hover. Manual — part 100
Appendix A-1
Control item
fixing to the
23
2N
m
Torque wrench
Steel plate gauge 100mm
hexagon flange nut (Q32012)
hexagon flange nut (Q32012)
Control item
locate the
riage and fix it with
some bolts(Q32012),
90
1 0 N
m .
Torque wrench
Appendix A-2
the fixed torque of nut 2 in the Figure is 70
10N m
the torque is: 70
10N
m the fixed
Connection of steering linkage co-
assembly and
fixed torque of nut 1 in the Figure is 25
Torque wrench
connection of steering linkage co-
assembly and left carriage
Torque wrench
Torque wrench
Connection of left right long longitudinal
tie assembly and carriage and rear axle
the fixed torque of nut 1 in the Figure is
Torque wrench
the fixed torque of nut 2 in the Figure is
Torque wrench
Connection of left right short longitudi-
nal tie assembly and carriage
the fixed torque of nut 3 in the Figure is
Torque wrench
Connection of cross tie assembly and rear
axle assembly
the fixed torque of nut 1 in the Figure is
Torque wrench
the fixed torque of nut 1 in the Figure is
Torque wrench
steering linkage co-assembly
cross universal joint
integral power steering general assembly
Connection of left right short longitudinal
tie assembly and rear axle assembly.
Connection of cross tie assembly and
carriage.
short longitudinal tie assembly (R)
long longitudinal tie assembly
short longitudinal tie
assembly (L)
Appendix A-3
1. (upper suspension arm steering knuckle ball pin nut) bolt
Locate the rear transverse stabilizer rob in the corresponding
position of carriage, symmetries the left and right during
installation.
Connection of rear transverse
stabilizer rod and rear axle
Viewing confirmation
the fixed torque of nut 2 in the Figure is 23
3N
m
Torque wrench
Connection of rear transverse
stabilizer rod and rear transverse
stabilizer robs connecting bar
assembly.
the fixed torque of nut 1 in the Figure is 63
5N
m
Torque wrench
rear transverse stabilizer
rear transverse stabilizer rod connecting bar assembly
bush
Upper suspension arm and upper suspension
arm steering knuckle ball pin
Steering gear cross tie ball pin
Lower suspension arm and lower suspension
arm steering knuckle ball pin
the fixed torque of nut 1 in the Figure is
145
15N
m
the fixed torque of nut 2 in the Figure is120
1 0 N
m
the fixed torque of nut 3 in the Figure is 230
2 0 N
m
Torque wrench
Torque wrench
Torque wrench
2. (steering gear cross tie ball pin nut) left steering
knuckle and wheel hub brake assembly
3. (lower suspension arm steering knuckle ball pin nut bolt
4. left steering knuckle and steering knuckle
and wheel hub brake assembly.
Appendix A-4
Connection of front transverse stabilizer rod
and carriage.
the fixed torque of nut 1in the Figure is 25
3N
m
the fixed torque of nut 2in the Figure is 63
5N
m
Connection of front transverse stabilizer rob
and front transverse stabilizer rod connecting
bar assembly
Torque wrench
Torque wrench
transmission assembly
drive shaft assembly
rear axle assembly
Drive shaft assembly installation
Plug the front part of drive shaft into transmission assembly
splinded shaft, after their good meshing, screw the central bearing
hexagon bolt into the corresponding screw hole of the carriage
Center bearing connecting bolt
the fixed torque of bolt 1 in the Figure is 65
5N
m
Drive shaft bolt
the fixed torque of bolt 2in the Figure is 65
5N
m
Torque wrench
Torque wrench
Viewing and handle
confirmation
front transverse stabilizer rod
bush
bush clip
front transverse stabilizer rod
connecting bar assembly
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст