Great Wall Hover. Manual — part 47
5. Install the torsion bar spring
(Refer to “Torsion Bar Spring”)
6. Tighten the nut of front shaft of lower arm to
specified torque
a. Install the wheel, remove the bracket and bounce the vehicle for
several times to make the vibration damper enters into the
stable status.
b. Align the assembly mark and tighten the nut to specified torque.
Tightening force: 240
20N
m
7. Check the wheel alignment parameter
(Refer to 4-Wheel Alignment)
special tools
Upper suspension arm
Disassembly of upper suspension arm
1. Disconnect the upper ball pin from the steering
knuckle
Remove the split pin and nut; use the special tools to disconnect
the upper ball pin from the steering knuckle.
2. Remove the brake oil pipe on the upper arm shaft
a. Use the open-end wrench to screw off the oil pipe tight nut.
b. Pull out the brake oil pipe and plug it by the rubber plug.
Remarks: There are two two-way valves for rear brake oil pipe
beside the right upper arm shaft ; when remove the right
upper suspension arm, it must remove four oil pipe tight nuts
in the place and plug it by the rubber plug to prevent the brake
fluid from overflowing.
3. Disconnect the brake hose form the brake caliper
Remove the hollow bolt and disconnect the brake hose form the
brake caliper
Remarks: Must not lose the copper gasket seal.
4. Disconnect the brake hose from the upper arm oil
pipe bracket.
Use the pliers to pull out the sheet steel spring clip and discon-
nect the brake hose from the upper arm oil pipe bracket.
5. Remove the upper suspension arm
Remove two bolts and remove the upper suspension from the
arm carriage.
Remarks: Keep the adjusting shim and don’t lose it. Record
the thickness of front and rear adjusting shim for convenience
of reinstalling them in the original position.
Replacement of upper arm bush
1. Remove the bush
a. Remove the bolt and washer
.
b. Use the special tools to push out the bush.
c. Remove the upper arm shaft; remove another bush in same proce-
dure
2. Install the bush
a. Use the special tools to press in the bush.
b. Install the upper arm shaft; use the special tools to press inanother
bush.
3. Tighten the upper arm shaft to specified torque.
a. Coat the screw of both ends of upper arm shaft with the screw
lock sealant; install the washer and nut.
Remarks: Adjust the position of upper lower; make the installa-
tion plane of ball pin is vertical to the installation plane of upper
arm shaft.
special tools
special tools
special tools
b. Tighten the upper arm shaft nut to specified torque.
Tightening force: 210
10N
m
Installation of upper suspension arm
1. Install the upper suspension arm on the carriage
a. Install the upper suspension arm and camber adjusting shim.
b. Tighten all bolts to the specified torque.
Tightening force: 200
10N
m
Remarks: Install the shim with same quantity and thickness to
the original position.
2. Connect the brake oil pipe of upper arm shaft
Tighten the oil pipe compression nut to specified torque.
Tightening force: 15-17N
m
Remarks: It should tighten four connector of two two-way
valves to the specified torque if disassemble the right upper
arm.
3. Connect thebrakehosetotheupperarmoilpipebracket
a. Thread the brake hose from the hole on upper arm oil pipe
bracket.
b. Use the hand hammer to knock in the sheet steel spring clip to
fix the brake hose.
4. Connect the upper ball pin to the steering knuckle
a. Tighten the slotted nut according to the specified torque.
Tightening force: 145
15N
m
b. Install the new split pin.
Remarks: It should align the notch of nut with the pinhole
when install the split pin; the nut can be tightened but not
loosed during the alignment.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст