Great Wall service chassis and body Manual — part 36
SA-40
Change of Lower Arm Shaft Bush and Tube
1.
Tear down the lower arm shaft bush and shaft tube:
(a)
Tear down the large and small pinch-off gaskets of the
lower arm shaft bush first.
(b)
Tear down the lower arm shaft bush and tube.
2.
Mount the lower arm shaft bush and tube.
(a)
Press down the lower arm shaft bush and tube.
(b)
Press down the large and small pinch-off gaskets of the
lower arm shaft bush.
Mount of Lower Arm
1.
Mount on the lower arm
Align the marks on the eccentric gasket and on the frame, and
then screw up the lower arm bolt.
2.
Connection for lower ball stud and lower arm:
Mount the lower ball stud and the lower arm ball stud seat
together.
Fastening torque
(142 0)Nm
3.
Vibration damper mount
Mount the vibration damper on the lower arm bracket;
Fastening torque
(137 0)Nm
Suspension System and Automobile Axle (SF/2WD)
Front Suspension (Lower Arm and Vibration Damper)
SA-41
4.
Mount the transverse stabilizer rod on the lower arm;
Fastening torque
(23 )Nm
5.
Check the Alignment of Front Wheel;
(See Page SA-6)
Suspension System and Automobile Axle (SF/2WD)
Front Suspension (Lower Arm and Vibration Damper)
SA-42
Upper Arm
Dismantle of Upper Arm
1.
Tear down the torsion rod spring:
(See page SA-19)
2.
Tear down the upper ball stud:
(a)
Support the upper arm with a jack.
(b)
Tear down the four sets of bolt and nut.
3.
Upper arm dismantle
Tear down the bolts to take down the upper arm.
Change of the Upper Arm Shaft Bush
(Short) and the Upper Arm Shaft Bush
and Tube
1.
Tear down the upper arm shaft bush (short) and the
upper arm shaft bush and tube (long)
(a)
Tear down the torsion bar yoke, the nuts as well as the
large and small pinch-off gaskets of the upper arm shaft
bush.
(b)
Push out the upper arm shaft bush (short) and upper arm
shaft bush and tube.
2.
Mount on the upper arm shaft bush (short) and the upper
arm shaft bush and tube (long):
(a)
Press the upper arm shaft bush and tube (long) in the
upper arm, and encase the upper swing arm shaft, and
then encase the upper arm shaft bush (short).
(b)
Mount on the large and small pinch-off gaskets of upper
arm shaft bush and screw up the nuts.
Fastening torque
(225 )Nm
(c)
Mount on the torsion bar yoke.
Notice: the notch of torsion bar yoke should face
downward;
Fastening torque
(89 )Nm
Suspension System and Automobile Axle (SF/2WD)
Front Suspension (Upper Arm)
SA-43
Mount of Upper Arm
1.
Screw up the axle nut of upper arm according to the
specified torque;
Fastening torque
(225 )Nm
2.
Mount on the upper arm;
Screw up the three bolts of the upper swing arm shaft according
to the specified torque;
Fastening torque
(178 5)Nm
3.
Connect the upper arm ball stud with the upper arm;
Use four sets of bolt and nut to connect the upper arm ball stud
and the upper arm.
Fastening torque
(27 )Nm
4.
Mount the torsion rod spring;
5.
Check the Alignment of Front Wheel:
(See Page SA-6)
Suspension System and Automobile Axle (SF/2WD)
Front Suspension \(Lower arm, Guide Lever and Transverse Stabilizer Rod)
Guide Lever
(See page SA-26)
Transverse Stabilizer rod
(See page SA-27)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст