Great Wall Florid. Manual — part 67
GWFLORID Maintenance Manual
266
Front seat removal and installation
Removal
1. Disconnect the seat belt terminal harness (seat bottom).
2. Remove the rear foundation hoods 1 & 2 and mounting
bolts 3 & 4.
3. Remove the front foundation hoods 1 & 2 and mounting
bolts 1 & 2.
4. Remove the seat.
Installation
Special Note: Different metals making direct contact
will accelerate corrosion. Make sure to use the correct
fastening piece to avoid premature corrosion.
1. Install the seat.
2. Connect the seat belt terminal harness.
3. Tighten the rear foundation bolt and install the rear
foundation hood.
4. Tighten the front foundation bolt and install the front
foundation hood.
Remarks: Front seats are symmetrical.
Seats
Components
Areas of Importance
1. Pay attention to safety in the process of removal, transportation, and installation, as to avoid
scratching or crushing injury caused by the seat.
2. Take note to protect the inner decorative components in the process of installation and transporta-
tion, as to avoid scratching the side panels.
3. After finishing installation, make sure to calibrate the tightening torque of mounting bolts.
Rear seat
Front passenger seat
Driver seat
Backrest regulating lever
Rear foundation
hood 1
Rear
foundation
hood 2
Front
foundation
hood 1
Front foundation hood 2
Mounting bolt 1
Mounting bolt 2
Mounting bolt 4
Mounting bolt 3
267
Vehicle Body
Rear seat removal and installation
Removal
1. Remove the mounting bolts (5) on the
40% of the rear seat backrest (3).
2. Remove the mouting bolts (6) on the
60% of the rear seat backrest (4).
3. Lift the rear seat cushion up and make
hook 11 slide out of clamping frame 9.
4. Continue to lift the seat cushion up, and tilt it upwards
to make hook 12 behind seat cushion slide out of the
rear seat fixed cross member hook 13. Finally, remove
the rear seat cushion.
Remarks: Mounting bolt (2) refers to the rear seat backrest (1)
mounting bolt.
Installation
Special Note: Different metals making direct contact
will accelerate corrosion. Make sure to use the correct
fastening piece to avoid premature corrosion.
1. Hang hook 12 behind the seat cushion on the fixed
cross member hook 13, and then press the hook under
the cushion into clamping frame 9.
2. Install the rear fixed cross member (7) and mounting
bolt (8) of the rear seat on the vehicle body.
3. Install the mounting bolts (6) of the 60% rear seat
backrest (4).
4. Install the mounting bolts (5) of the 40% rear seat
backrest (3).
1
2
3
4
5
6
7
8
9
10
9
2
1
5
6
8
8
11
12
GWFLORID Maintenance Manual
268
Sunroof Assembly
Components
N·m
: Specified torque
Sunroof panel
Sunroof window weatherstrip
Movable sun visor
Slider
Upper trim strip
Lower trim strip
Roof drip channel
Guide device latch hook
End piece
Guide rail assembly
Bolt
Spring
Wind guard
Bolt
Rear guide device
Air guide plate
Spacing tube
Drive device
4.5
3.5
269
Vehicle Body
Fault classification
Fault symptom
Fault diagnosis
Fault maintenance
Window panel
motion failure
Window panel (sunroof)
cannot open, rise, or close
from its initial position
Check if anything is blocking the guide rail
for window panel movement. Check whether
the mechanism moves smoothly or stiffly.
Check whether the mechanism is broken.
Check whether the guide rail is deformed.
Check whether the motor works normally.
Replace the sunroof guide rail assem-
bly. Replace the motor.
The window panel can-
not close while half-
opened or half-tilted
Diagnosis: Check whether there are oddities
impeding the window panel's movement .
Check whether the wind guard or rear roof
drip channel is arched or deformed.
Clean the objects and close the sun-
roof by force when the jam protection
function is started, then open it again
for operation. Replace the wind guard
and rear roof drip channel.
Sun visor push/pull
fault
Sun visor cannot open
or close normally
Check whether the guide rail for the sun visor
is blocked by oddities. Check whether the sun
visor bracket is broken.
Clean the oddities in the guide rail.
Change the sun visor. Change the sun
visor bracket.
The sun visor cannot open
and close completely
Check whether the front part of sun visor
arches. Check whether the sun visor lever has
been broken off.
Replace the sun visor. Replace the
sun visor lever.
Sunroof leakage fault Sunroof leakage
Check the clearance between the window
panel and the car roof hatch.
Adjust and enlarge the window panel
weatherstrip.
Check whether a build up of sand or dust ex-
ists on the surface of window panel weather-
strip.
Clean the weatherstrip surface and
car roof hatch.
Check the sealing conditions between the
guide rail & front roof drip channel and rear
roof drip channel.
Replace the sunroof guide rail assem-
bly.
Check whether the front roof drip channel
and rear roof drip channel are broken.
Replace the sunroof guide rail assem-
bly or rear roof drip channel.
Abnormal noise
There is abnormal noise
when closing the sunroof
(1) Check the positioning of the closed win-
dow panel.
(2) Check whether the wind deflector spring is
in the right position.
(3) Check whether the rear roof drip channel's
fixed spring has broken off.
(4) Check whether the wind deflector buffer
rubber block has broken off.
(1) Adjust the window panel's position.
(2) Place the wind deflector spring in
the right position .
(3) Re-install the fixed spring.
(4) Re-install the rubber block.
There is abnormal
noise when the sun-
roof is operating
(1) Check whether the motor is working nor-
mally.
(2) Check whether oddities exist in the guide
rail for mechanism movement .
(3) Check the grease's conditions on the mov-
ing components .
(4) Check whether the moving components
are broken.
(1) Replace the motor.
(2) Clean out any contamination.
(3) Lubricate the components.
(4) Replace the components or the
sunroof guide rail assembly.
Troubleshooting
Sunroof assembly removal
1. Remove the ceiling.
2. Disconnect and pull the connector of the sunroof ac-
tuator out.
3. Pull the four sunroof drainage pipes out (positions indi-
cated by the arrows in the diagram).
4. Remove the sunroof.
Remove the bolt and plastic gasket, and carry the sunroof
assembly out of car with the help of an assistant.
Sunroof
assembly
Mounting bolt
Drive device
Plastic gasket
Drainage pipe port
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст