Great Wall Florid. Manual — part 65
GWFLORID Maintenance Manual
258
7. Disconnect the wire harness of the left & right fog lamps.
8. Remove the bumper attachments.
Remove the front bumper plastic support and energy absorb-
ing block from the vehicle body respectively.
9. Remove the bumper bracket.
Screw off the cross slot & concave hexagon head self-tapping
screw and large washer subassembly (Q2756319+Q422) on the
left / right side mounting bracket of the front bumper, and pull
the left / right side mounting bracket out.
Front bumper body
Front bumper body
Front bumper energy
absorbing block
Front bumper plastic
support
Front bumper left side mounting bracket
Cross slot & concave
hexagon head self-
tapping screw and large
washer subassembly
259
Vehicle Body
Rear Bumper
Components
Rear bumper removal
1. Remove the trim panel.
Screw off the cross slot & concave hexagon head self-tap-
ping screw and large washer subassembly, which are on the
rear bumper's left & right trim panel, the rear bumper trim
panel buckle, and the expansion button whose bottom is con-
nected with the bumper body. Then pull the left & right trim
panel of the rear bumper off.
1
13
9
5
3
12
7
4
14
16
15
11
18
6
1
1
1
13
13
13
11
17
3
2
10
8
Rear bumper body
Rear bumper left side trim panel
Cross slot & con-
cave hexagon head
self-tapping screw
and large washer
subassembly
Rear bumper trim
panel buckle
Expansion button
1. Cross slot & concave hexagon head self-tapping screw and large
washer subassembly
2. Rear mounting bracket LH of the rear bumper
3. Rear bumper mounting bolt
4. Hexagon nut for flange face
5. Rubber cushion of the rear bumper central mounting bracket
6. Rear bumper central mounting bracket bolt
7. Central left mounting bracket of the rear bumper
8. Central right mounting bracket of the rear bumper
9. Rear mounting bracket RH of the rear bumper
10. Front mounting bracket RH of the rear bumper
11. Rear bumper trim panel buckle
12. Rear bumper right trim panel
13. Expansion button
14. Rear bumper body
15. Rear bumper plastic buffer anchor
16. Rear bumper drawbar close lid
17. Rear bumper left trim panel
18. Front mounting bracket LH of the rear bumper
GWFLORID Maintenance Manual
260
2. Remove the nut and gasket.
Screw off the hexagon nut for flange face from the rear bum-
per left & right side central mounting bolt, and the rubber
cushion of the rear bumper left & right side central mounting
bracket.
3. Remove the expansion button connecting the left &
right side bracket below the rear bumper and vehicle
body.
4. Remove the bumper mounting bolt.
Screw off the rear bumper mounting bolt connecting the left
& right side above the rear bumper and vehicle body.
5. Pull the bumper out.
Pull the rear bumper out of the left & right side bracket of
the rear bumper, and make the central part of the rear bum-
per slide out along the rear bumper central mounting bracket
bolt.
6. Remove the three rear bumper plastic buffer anchor
from the rear impact beam.
Rear bumper body
Rear bumper body
Rear bumper body
Rear bumper body
Rear bumper
Rear bumper plastic buffer anchor
Central left mounting
bracket of the rear bumper
Rear mounting bracket
LH of the rear bumper
Front mounting bracket
LH of the rear bumper
Rear bumper central
mounting bracket bolt
Rear bumper mounting bolt
Expansion button
Hexagon nut for flange face
Rubber cushion of the
rear bumper central
mounting bracket
261
Vehicle Body
7. Remove the front bracket.
Screw off the cross slot & concave hexagon head self-tap-
ping screw and large washer subassembly on the left & right
front mounting bracket of the rear bumper, and pull the left
& right front mounting bracket of rear bumper out.
8. Remove the rear bracket.
Screw off the cross slot & concave hexagon head self-tap-
ping screw and large washer subassembly on the left & right
rear mounting bracket of the rear bumper, and pull off the
left & right rear mounting bracket of the rear bumper.
Engine hood lock cable removal and installa-
tion
Removal
1. Open the engine hood.
2. Remove the engine hood release lever from the dash-
board.
3. Remove the cable from the engine hood release lever
4. Remove the bolts and engine hood lock latch release
mechanism.
5. Remove the cable from the engine hood lock latch re-
lease mechanism assembly.
Installation
Areas of Importance: Different metals making direct
contact will accelerate corrosion. Make sure to use the
correct fastening piece to avoid premature corrosion.
1. Install the cable onto the engine hood lock latch re-
lease mechanism assembly.
2. Install the engine hood lock latch release mechanism
assembly with the bolts.
3. Install the cable onto the engine hood lock latch re-
lease lever.
4. Install the engine hood release lever onto the dash-
board.
Rear bumper body
Rear bumper body
Rear mounting bracket LH of the rear bumper
Cross slot & concave hexagon head self-
tapping screw and large washer subassembly
Front mount-
ing bracket LH of
the rear bumper
Cross slot & concave
hexagon head self-tap-
ping screw and large
washer subassembly
Engine hood
lock latch release
mechanism
Cable
Bolt
Dashboard
Release lever
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст