Great Wall Florid. Manual — part 60
GWFLORID Maintenance Manual
238
5. Install the rear door lock assembly.
Install the assembled assembly, tighten the lock mounting
screws (pay attention to put the outwardly open swing arm
lever clip of the lock onto the outer opened fork of the out-
side handle framework), and then insert the wire harness
plug-in into the door lock socket.
6. Install the cable buckle.
7. Install the inside handle.
Clamp the inside handle clip to the door inner decoration
board, and then firmly press the inside handle clip dowel pin
into the mounting hole.
8. Install the rear door outside handle decorative cap, and
tighten the decorative cap mounting bolt.
9. Install the inside handle screw.
When the door cylinder panel assembly is installed, tighten
the inside handle's mounting screw.
10. Install the rear door lock latch.
11. For rear door lock removal, please simply reverse the
installation steps.
Door lock fork
Inside handle dowel pin
Inside handle clip
Mounting screw
Door lock inside handle
Rear door lock latch
Q2580822
239
Vehicle Body
Trunk door lock installation and removal
1. Install the trunk door outside handle.
Install the trunk door outside handle assembly, tighten the
mounting screw, and install the wire harness plug-in.
Trunk Door Lock Assembly
Components
2. Install the trunk door main lock assembly.
Install the trunk door main lock assembly, and tighten the
mounting screw.
3. Install the trunk lock latch.
4. For trunk lock removal, please simply reverse the
installation steps.
Trunk door lock assembly
Q1460620 (Q402) F3
Trunk door lock latch
Q2580820 + Q141F32
Q1840616F3
Trunk door outside handle assembly
Connect the central door lock controller
Connect the door lamp indicator
Q1460620 (Q402) F3
Connect the door
lamp indicator
Connect the central door
lock controller
Q1840616F3
GWFLORID Maintenance Manual
240
Wiper arm and vent panel removal and in-
stallation
1. Remove the bolt cover of the wiper arm.
2. Remove the retaining bolt of the wiper arm.
3. Wobble the wiper arm to remove it.
Wiper Arm and Vent Panel Assembly
Components
4. Take off the rear weatherstrip of the engine hood from
the vent panel.
5. Remove the screws from the two ends of vent panel.
6. Remove the expansion button in the middle of the right
and left vent panels.
7. For wiper arm and vent panel Installation, please simply
reverse the removal steps.
Right wiper arm
Left wiper arm
Wiper arm bolt cover
Wiper arm bolt
Left vent panel
Right vent panel
Engine hood rear weatherstrip
Screw
Screw
Wiper arm bolt cover
Wiper arm bolt
Wiper arm
Engine hood rear
weatherstrip
Vent panel expansion button
Screw
241
Vehicle Body
Front & Rear Window Glasses
Windshield removal
1. Use steel wire to strip the glass sealant from the four
sides of the windshield.
2. Remove the windshield and trim strip from the vehicle.
3. Remove the trim strip and inner rearview mirror from
the windshield.
4. Use a blade to remove the glass sealant on the end of
the glass.
5. Use a polisher to remove the glass sealant on the glass
window frame, and polish clean the glass sealant.
Rear window glass removal
1. Disconnect the battery's negative cable.
2. Disconnect the defogger electrical connector of the
rear window.
3. Use steel wire to strip the glass sealant off the rear
window glass.
4. Remove the rear window glass.
5. Use a blade to remove the glass sealant.
6. Use a polisher to remove the glass sealant on the
glass frame.
Rear window glass installation
1. Coat glass sealant primer on the rear door's sheet
metal seam and rear window glass.
2. Coat the rear window glass with glass sealant, glass
sealant height is 10±2 mm.
3. Install the rear window glass.
4. Use adhesive tape fix the rear window glass and back
door, and fix the rear window glass.
5. Connect the defogger electrical connector of the rear
window.
6. Connect battery's negative cable.
7. Remove the tape after the glass sealant has been on
24 hours.
Windshield installation
1. Install the trim strip and inner rearview mirror on the
windshield.
2. Coat the windshield frame and its edge with primer.
3. Use a glue gun to coat the windshield with glass
sealant, glass sealant height is 10±2 mm.
4. Use adhesive tape fix the windshield and the
windshield's outside sheet metal.
5. Remove the tape after the glass sealant has solidified
for 24 hours.
Windshield
Windshield trim strip
Inner rearview
mirror
Defogger electrical connector
Rear window glass
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст