Mazda 6. Manual — part 331
T–84
WARNING AND INDICATOR SYSTEM
OIL PRESSURE SWITCH INSPECTION
A6E811818500W01
1. Verify that the oil pressure warning light illuminates when the ignition switch is at ON position.
2. Verify that the oil pressure warning light goes off when the engine is started.
• If the oil pressure warning light does not illuminate or remains illuminated, inspect the related wiring
harness.
— If the related wiring harness are normal, inspect the oil pressure. (See
• If the oil pressure is normal, replace the oil pressure switch.
End Of Sie
HORN REMOVAL/INSTALLATION
A6E811866790W01
1. Disconnect the negative battery cable.
2. Bend the mud guard.
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
End Of Sie
INFORMATION DISPLAY REMOVAL/INSTALLATION
A6E811855000W01
1. Disconnect the negative battery cable.
2. Remove the center panel module. (See
T–96 CENTER PANEL MODULE REMOVAL/INSTALLATION
3. Remove the LCD unit. (with car-navigation system) (See
T–98 LCD UNIT REMOVAL/INSTALLATION
.)
4. Remove the center box. (without car-navigation system)
5. Remove in the order indicated in the table.
6. Install in the reverse order of removal.
Information Display Removal Note
1. Squeeze the tabs of information display and pull it forward to it.
End Of Sie
1
Bolt
2
Connector
3
Horn
A6E8118W001
1
Short harness
2
Information display
(See
T–84 Information Display Removal Note
3
LCD unit (with car-navigation system)
Center box (without car-navigation system)
A6E8118W008
THEFT-DETERRENT SYSTEM
T–85
T
BONNET SWITCH INSPECTION
A6E812001084W01
Note
• Bonnet switch has a built-in bonnet lock.
1. Open the bonnet.
2. Disconnect the negative battery cable.
3. Remove the radiator grille.
4. Disconnect the bonnet switch connector.
5. Check the continuity between the bonnet switch
terminals A and B using an ohmmeter.
• If there is continuity, replace the bonnet
switch.
6. Lock the bonnet lock using a flat-head
screwdriver or equivalent as shown.
7. Check the no continuity between the bonnet
switch terminals A and B using an ohmmeter.
• If there is no continuity, replace the bonnet
switch.
Caution
• After the inspection, unlock the bonnet
lock. If closing the bonnet with the
bonnet lock locked, the bonnet lock and/
or bonnet striker may be broken.
End Of Sie
THEFT-DETERRENT SYSTEM
A6E8120W002
A6E8120W003
T–86
THEFT-DETERRENT SYSTEM
THEFT-DETERRENT CONTROL MODULE REMOVAL/INSTALLATION
A6E812067790W01
1. Disconnect the negative battery cable.
2. Remove the center panel module. (See
T–96 CENTER PANEL MODULE REMOVAL/INSTALLATION
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
End Of Sie
THEFT-DETERRENT CONTROL MODULE INSPECTION
A6E812067790W02
1. Remove the theft-deterrent control module without disconnecting the connectors.
2. Measure the voltage at the theft-deterrent control module terminals as indicated below.
3. Disconnect the theft-deterrent control module connector before inspecting for continuity at terminals L, Q, S, T,
and V.
4. If not as specified, inspect the parts listed under “Action.”
• If the parts and wiring harnesses are okay but the system still does not work properly, replace the
theft-deterrent control module.
Terminal Voltage Table (Reference)
1
Screw
2
Connector
3
Theft-deterrent control module
A6E8120W001
Terminal
Signal
Connected to
Test condition
Voltage (V)/
continuity
Action
A
—
—
—
—
—
B
IG1
METER IG 15 A
fuse
Ignition switch at ON
position
B+
• Inspect ignition switch
(See
• Inspect METER IG 15 A
fuse
• Inspect related harness
Ignition switch at
LOCK or ACC position
Below 1.0
C
Power supply
ROOM 15 A fuse
Under any condition
B+
• Inspect ROOM 15 A fuse
• Inspect related harness
D
—
—
—
—
—
E
—
—
—
—
—
F
Intruder sensor power
supply
Intruder sensor
Theft-deterrent system
pre-arming or arming
B+
• Inspect related harness
Other
Below 1.0
G
Security light on/off
Security light
Security light on
Below 2.0
• Inspect security light
• Inspect related harness
Security light off
B+
H
Hazard warning signal
output
Flasher unit
Theft-deterrent system
alarm: Active
Alternates
between
below 1.0
and B+
• Inspect flasher unit
(See
• Inspect related harness
Theft-deterrent system
alarm: Other
B+
A6E8120W004
THEFT-DETERRENT SYSTEM
T–87
T
I
Theft-deterrent siren
on/off
Theft-deterrent
siren
Theft-deterrent system
alarm: Active
Alternates
between
below 1.0
and B+
• Inspect related harness
Theft-deterrent system
alarm: Other
B+
J
• Theft-deterrent
system recognition
signal output
• Keyless entry
system operation
signal input
Door lock timer unit Under any condition
B+
• Inspect door lock timer
)
• Inspect related harness
K
Horn on/off
Horn relay
Theft-deterrent system
alarm: Other
B+
• Inspect horn relay
(See
)
• Inspection related
harness
Theft-deterrent system
alarm: Active
Alternates
between
below 1.0
and B+
L
Theft-deterrent control
module ground
GND
Under any condition:
inspect for continuity
to ground
Yes
• Inspect GND
M
Key reminder switch
on/off
Key reminder
switch
Key reminder switch
on (key inserted)
B+
• Inspect key reminder
switch
(See
)
• Inspect related harness
Key reminder switch
off (key removed)
Below 1.0
N
—
—
—
—
—
O
Intruder sensor on/off
Intruder sensor
Theft-deterrent system
pre-arming or arming
Alternates
between
below 1.0
and B+
• Inspect related harness
P
—
—
—
—
—
Q
Bonnet open/closed
Bonnet switch
Bonnet switch on:
inspect for continuity
to ground
Yes
• Inspect bonnet switch
(See
)
• Inspect related harness
Bonnet switch off:
inspect for continuity
to ground
No
R
Trunk compartment
light switch/cargo
compartment light
switch on/off
• Trunk
compartment
light switch
• Cargo
compartment
light switch
Trunk compartment
light switch/cargo
compartment light
switch on
Below 1.0
• Inspect trunk
compartment light switch
(See
COMPARTMENT LIGHT
SWITCH INSPECTION
)
• Inspect cargo
compartment light switch
(See
COMPARTMENT LIGHT
SWITCH INSPECTION
)
• Inspect related harness
Trunk compartment
light switch/cargo
compartment light
switch off
B+
S
Door open/closed
Door switch
Any door open:
inspect for continuity
to ground
Yes
• Inspect door switch
(See
)
• Inspect related harness
All doors closed:
inspect for continuity
to ground
No
Terminal
Signal
Connected to
Test condition
Voltage (V)/
continuity
Action
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст