Mazda 6. Manual — part 317
T–28
EXTERIOR LIGHTING SYSTEM
5. Set the headlights 3 m {10 ft} from the wall.
6. While adjusting one headlight, mask the other.
7. Start the engine to charge the battery.
8. Turn on the high-beam headlights.
9. Set the headlight leveling switch to 0 position.
10. Adjust the headlights by turning the adjusting
screws as shown in the figure. Loosen the screws
first, then tighten them.
Note
• If the adjusting screws are tightened first,
then loosened, they will continue to loosen
when the vehicle is in motion and may cause
the headlights to become misaligned.
End Of Sie
HEADLIGHT BULB REMOVAL/INSTALLATION
A6E811251030W02
Low-beam
Halogen type
1. Disconnect the negative battery cable.
2. Remove the fasteners, then pull back the mudguard.
3. Remove in the order indicated in the table.
Caution
• A halogen bulb generates extremely high
heat when it is used. If the surface of the
bulb is soiled, excessive heat will build
up and the light's life will be shortened.
When replacing the bulb, hold the metal
flange, not the glass.
4. Install in the reverse order of removal.
Headlight bulb removal note
1. Release the bulb pressing wire to remove the headlight bulb.
A6E8112W157
A6E8112W124
A6E8112W136
1
Cover
2
Connector
3
)
A6E8112W105
EXTERIOR LIGHTING SYSTEM
T–29
T
Discharge type
Caution
• Incorrect servicing of the discharge headlights could result in electrical shock. Before servicing
the discharge headlights, always refer to the “Discharge headlight service warnings.” (See
DISCHARGE HEADLIGHT SERVICE WARNINGS
)
1. Disconnect the negative battery cable.
2. Remove the fasteners, then pull back the mudguard.
3. Remove in the order indicated in the table.
Caution
• A bulb generates extremely high heat
when it is used. If the surface of the bulb
is soiled, excessive heat will build up and
the light's life will be shortened. When
replacing the bulb, hold the metal flange,
not the glass.
4. Install in the reverse order of removal.
High-beam
1. Disconnect the negative battery cable.
2. Remove in the order indicated in the table.
Caution
• A halogen bulb generates extremely high
heat when it is used. If the surface of the
bulb is soiled, excessive heat will build
up and the light's life will be shortened.
When replacing the bulb, hold the metal
flange, not the glass.
3. Install in the reverse order of removal.
Headlight bulb removal note
1. Release the bulb pressing wire to remove the headlight bulb.
End Of Sie
1
Cover
2
Connector
3
Bulb cover
4
Discharge headlight bulb
A6E8112W106
1
Cover
2
Connector
3
Headlight bulb (See
)
A6E8112W107
T–30
EXTERIOR LIGHTING SYSTEM
DISCHARGE HEADLIGHT CONTROL UNIT REMOVAL/INSTALLATION
A6E811251030W03
Caution
• Incorrect servicing of the discharge headlight control unit could result in electrical shock. Before
servicing the discharge headlight control unit, always refer to the “Discharge headlight service
warnings.” (See
T–25 DISCHARGE HEADLIGHT SERVICE WARNINGS
• When replacing the discharge headlight control unit, configuration procedure must be done
before removing the auto leveling control unit. After replacing the discharge headlight control unit,
perform the headlight zeroset for auto leveling control unit.
1. Configurate the discharge headlight control unit (when only replacing it). (See
)
2. Disconnect the negative battery cable.
3. Remove the front combination light. (See
T–26 FRONT COMBINATION LIGHT REMOVAL/INSTALLATION
4. Remove in the order indicated in the table.
5. Install in the reverse order of removal.
6. Perform the headlight zeroset for the discharge
headlight control unit (when only replacing it).
(See
)
End Of Sie
AUTO LEVELING CONTROL UNIT CONFIGURATION
A6E811251030W04
1. Connect the SST (WDS or equivalent) to the
DLC-2.
2. Input vehicle information following the directions
on the screen.
3. Select “Module programming”.
4. Select “Programmable module installation”.
5. When performing configuration corresponding to
each auto leveling control unit, select the following
items and perform procedures according to
directions on the screen.
Items
• Main: “LHID”
• Sub: “RHID”
6. Retrieve DTCs by the WDS or equivalent, then verify that there is no DTC present.
• If DTC is present, perform applicable DTC inspection.
End Of Sie
1
Bolt
2
Discharge headlight control unit
A6E8112W141
DLC-2
A6E3970W002
EXTERIOR LIGHTING SYSTEM
T–31
T
HEADLIGHT ZEROSET
A6E811251030W05
Note
• When the configuration is not set for the auto leveling control unit, headlight zeroset cannot be executed.
1. Adjust the tire air pressure to the specification.
2. Position the unloaded vehicle on a flat, level surface.
3. Connect the SST (WDS or equivalent) to the DLC-2.
4. Turn the ignition switch to ON position.
5. Turn on the headlights (low-beam).
6. Input the vehicle information following the directions on the screen.
7. Confirm that the WDS or equivalent identifies the vehicle, and select “Datelogger”.
8. After the screen appears, select “LHID” under “Modules” from the cascading menu.
9. After the next screen appears, select “CALAXLSN#”.
10. On the graphic display that appears, press the
icon near the top right of the screen indicated by a
1 in the figure.
11. After the next screen appears, press the icon
indicated by a 2 in the figure.
12. After pressing the icon indicated by the 2, press
the icon indicated by a 3 or 4 in the figure to
execute the zeroset setting.
Note
• Pressing an icon indicated by 3 or 4 once
will execute the headlight zeroset setting.
13. After executing the headlight zeroset setting,
perform an on-board diagnostic test and verify
that no DTCs are displayed.
14. Perform the headlight aiming adjustment. (See
End Of Sie
A6E8112W158
A6E8112W159
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст