Mazda 6. Manual — part 99
TOWING
GI–27
GI
FRONT
1. Remove the towing eyelet and the lug wrench from the trunk.
2. Wrap a screwdriver or similar tool with a soft cloth to prevent damage to the painted bumper and open the cap
located on the front bumper, below the left headlight.
Caution
• The cap cannot be completely removed.
Do not use excessive force as it may
damage the cap or scratch the painted
bumper surface.
3. Securely install the towing eyelet using the lug
wrench.
4. Hook the towing rope to the towing eyelet.
Caution
• If the towing eyelet is not securely
tightened, it may loosen or disengage
from the bumper when towing the
vehicle. Make sure that the towing eyelet
is securely tightened to the bumper.
REAR
End Of Sie
A6E2024W004
A6E2024W002
A6E2024W003
A6E2024W001
GI–28
IDENTIFICATION NUMBER LOCATIONS
VEHICLE IDENTIFICATION NUMBER(VIN)
A6E202600010W01
End Of Sie
ENGINE IDENTIFICATION NUMBER
A6E202600010W02
End Of Sie
IDENTIFICATION NUMBER LOCATIONS
A6E2026W004
A6E2026W001
NEW STANDARDS
GI–29
GI
NEW STANDARDS
A6E202800020W01
• Following is a comparison of the previous standard and the new standard.
NEW STANDARDS
New Standard
Previous Standard
Remark
Abbrevi-
ation
Name
Abbrevi-
ation
Name
AP
Accelerator Pedal
—
Accelerator Pedal
ACL
Air Cleaner
—
Air Cleaner
A/C
Air Conditioning
—
Air Conditioning
BARO
Barometric Pressure
—
Atmospheric Pressure
B+
Battery Positive Voltage
Vb
Battery Voltage
—
Brake Switch
—
Stoplight Switch
—
Calibration Resistor
—
Corrected Resistance
#6
CMP sensor Camshaft Position Sensor
—
Crank Angle Sensor
CAC
Charge Air Cooler
—
Intercooler
CLS
Closed Loop System
—
Feedback System
CTP
Closed Throttle Position
—
Fully Closed
CPP
Clutch Pedal Position
—
Idle Switch
CIS
Continuous Fuel Injection System
—
Clutch Position
CS sensor
Control Sleeve Sensor
CSP sensor Control Sleeve Position Sensor
#6
CKP sensor Crankshaft Position Sensor
—
Crank Angle Sensor 2
DLC
Data Link Connector
—
Diagnosis Connector
DTM
Diagnostic Test Mode
—
Test Mode
#1
DTC
Diagnostic Trouble Code(s)
—
Service Code(s)
DI
Distributor Ignition
—
Spark Ignition
DLI
Distributorless Ignition
—
Direct Ignition
EI
Electronic Ignition
—
Electronic Spark Ignition
#2
ECT
Engine Coolant Temperature
—
Water Thermo
EM
Engine Modification
—
Engine Modification
—
Engine Speed Input Signal
—
Engine RPM Signal
EVAP
Evaporative Emission
—
Evaporative Emission
EGR
Exhaust Gas Recirculation
—
Exhaust Gas Recirculation
FC
Fan Control
—
Fan Control
FF
Flexible Fuel
—
Flexible Fuel
4GR
Fourth Gear
—
Overdrive
—
Fuel Pump Relay
—
Circuit Opening Relay
#3
FSO
solenoid
Fuel Shut Off Solenoid
FCV
Fuel Cut Valve
#6
GEN
Generator
—
Alternator
GND
Ground
—
Ground/Earth
HO2S
Heated Oxygen Sensor
—
Oxygen Sensor
With heater
IAC
Idle Air control
—
Idle Speed Control
—
IDM Relay
—
Spill Valve Relay
#6
—
Incorrect Gear Ratio
—
—
—
Injection Pump
FIP
Fuel Injection Pump
#6
—
Input/Turbine Speed Sensor
—
Pulse Generator
IAT
Intake Air Temperature
—
Intake Air Thermo
KS
Knock Sensor
—
Knock Sensor
MIL
Malfunction Indicator Lamp
—
Malfunction Indicator Light
MAP
Manifold Absolute Pressure
—
Intake Air Pressure
MAF sensor Mass Air Flow Sensor
—
Airflow Sensor
MFL
Multiport Fuel Injection
—
Multiport Fuel Injection
OBD
On-Board Diagnostic
—
Diagnosis/SelfDiagnosis
OL
Open Loop
—
Open Loop
GI–30
NEW STANDARDS
#1 : Diagnostic trouble codes depend on the diagnostic test mode
#2 : Controlled by the PCM
#3 : In some models, there is a fuel pump relay that controls pump speed. That relay is now called the fuel pump
relay (speed).
#4 : Device that controls engine and powertrain
#5 : Directly connected to exhaust manifold
#6 : Part name of diesel engine
End Of Sie
—
Output Speed Sensor
—
Vehicle Speed Sensor 1
OC
Oxidation Catalytic Converter
—
Catalytic Converter
O2S
Oxygen Sensor
—
Oxygen Sensor
PNP
Park/Neutral Position
—
Park/Neutral Range
—
PCM Control Relay
—
Main Relay
#6
PSP
Power Steering Pressure
—
Power Steering Pressure
PCM
Powertrain Control Module
ECU
Engine Control Unit
#4
—
Pressure Control Solenoid
—
Line Pressure Solenoid Valve
PAIR
Pulsed Secondary Air Injection
—
Secondary Air Injection System
Pulsed
injection
—
Pump Speed Sensor
—
NE Sensor
#6
AIR
Secondary Air Injection
—
Secondary Air Injection System
Injection
with air
pump
SAPV
Secondary Air Pulse Valve
—
Reed Valve
SFI
Sequential Multipoint Fuel Injection
—
Sequential Fuel Injection
—
Shift Solenoid A
—
12 Shift Solenoid Valve
—
Shift A Solenoid Valve
—
Shift Solenoid B
—
23 Shift Solenoid Valve
—
Shift B Solenoid Valve
—
Shift Solenoid C
—
34 Shift Solenoid Valve
3GR
Third Gear
—
3rd Gear
TWC
Three Way Catalytic Converter
—
Catalytic Converter
TB
Throttle Body
—
Throttle Body
TP sensor
Throttle Position Sensor
—
Throttle Sensor
TCV
Timer Control Valve
TCV
Timing Control Valve
#6
TCC
Torque Converter Clutch
—
Lockup Position
TCM
Transmission (Transaxle) Control
Module
—
ECAT Control Unit
—
Transmission (Transaxle) Fluid
Temperature Sensor
—
ATF Thermosensor
TR
Transmission (Transaxle) Range
—
Inhibitor Position
TC
Turbocharger
—
Turbocharger
VSS
Vehicle Speed Sensor
—
Vehicle Speed Sensor
VR
Voltage Regulator
—
IC Regulator
VAF sensor Volume Air Flow Sensor
—
Air flow Sensor
WUTWC
Warm Up Three Way Catalytic
Converter
—
Catalytic Converter
#5
WOT
Wide Open Throttle
—
Fully Open
New Standard
Previous Standard
Remark
Abbrevi-
ation
Name
Abbrevi-
ation
Name
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст