Mazda 6. Manual — part 231
ENGINE SPEED SENSING POWER STEERING
N–7
N
STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION
A6E661432010W02
Warning
• Handling the air bag module improperly can accidentally deploy the air bag module, which may
seriously injure you. Read AIR BAG SYSTEM WARNINGS before handling the air bag module. (See
1. Remove in the order indicated in the table.
2. Install in the reverse order of removal.
3.
.
A6E0612W017
1
T–120 DRIVER-SIDE AIR BAG MODULE
)
2
Locknut
3
N–8 Steering Wheel Removal Note
)
N–8 Steering Wheel Installation Note
4
Column cover
5
6
Combination switch
7
Lower panel
8
Steering shaft
(See
N–8 Steering Shaft Installation Note
9
Joint cover
10
Dust cover
11
Steering lock mounting bolts
(See
N–8 Steering Lock Mounting Bolts Removal
)
(See
N–8 Steering Lock Mounting Bolts Installation
)
12
Steering lock component
N–8
ENGINE SPEED SENSING POWER STEERING
Steering Wheel Removal Note
Caution
• Do not try to remove the steering wheel by hitting the shaft with a hammer. The column will
collapse.
1. Set the vehicle in the straight-ahead position.
2. Remove the steering wheel using a suitable puller.
Steering Lock Mounting Bolts Removal Note
1. Make a groove in the heads of the steering lock
mounting bolts using a chisel and a hammer.
2. Remove the bolts using a screwdriver.
3. Disassemble the steering lock component.
Steering Lock Mounting Bolts Installation Note
1. Assemble the steering lock component to the steering shaft.
2. Verify that the lock operates correctly.
3. Install new steering lock mounting bolts.
4. Tighten the bolts until the heads break off.
Steering Shaft Installation Note
Caution
• Do not apply a shock in the axial direction of the shaft.
1. Lock the tilt lever.
2. Tighten bolt A.
3. Tighten nut B.
4. Tighten nut C.
Steering Wheel Installation Note
1. Set the wheels in the straight-ahead position, and install the steering wheel.
End Of Sie
A6E0612W018
A6E0612W020
A6E0612W103
ENGINE SPEED SENSING POWER STEERING
N–9
N
STEERING SHAFT INSPECTION
A6E661432100W01
1. Inspect the following.
(1) Column bearing for damage
(2) Steering shaft length
• Replace the steering shaft component as
necessary.
Length
211.6 mm {8.3 in}
2. Inspect the tilt and telescope operation
(1) Verify that the adjusting lever moves smoothly
from unlock position to lock position.
(2) Verify that the steering shaft is fixed firmly
when the adjusting lever is locked.
• Replace the steering shaft component as
necessary.
End Of Sie
A6E0612W022
A6E0612W023
N–10
ENGINE SPEED SENSING POWER STEERING
STEERING GEAR AND LINKAGE REMOVAL/INSTALLATION
A6E661432960W01
Caution
• Performing the following procedures without first removing the ABS wheel-speed sensor may
possibly cause an open circuit in the harness if it is pulled by mistake. Before performing the
following procedures, remove the ABS wheel-speed sensor (axle side) and fix it to an appropriate
place where the sensor will not be pulled by mistake while servicing the vehicle.
1. Remove in the order indicated in the table.
2. Install in the reverse order of removal.
3. After installation, inspect the toe-in. (See
.
A6E0612W108
1
Bolt (intermediate shaft)
(See
N–11 Bolt (Intermediate Shaft) Removal Note
)
(See
N–12 Bolt (Intermediate Shaft) Installation
)
2
Cotter pin
3
Nuts (tie-rod end ball joint)
4
Tie-rod end ball joint
(See
N–11 Tie-rod End Ball Joint Removal Note
5
Pressure pipe
6
Return pipe
7
Steering gear and linkage
(See
N–11 Steering Gear and Linkage Removal
)
(See
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст