Mazda 6. Manual — part 338
CRUISE CONTROL SYSTEM
T–111
T
Terminal Voltage Table (Reference)
Terminal
Signal
Connected to
Test condition
Voltage (V)
/Continuity
Action
A
Vehicle speed
• DSC HU/CM
(with DSC)
• ABS (ABS/
TCS) HU/CM
(with ABS
(ABS/TCS))
1. Ignition switch at ON
position and cruise control
main switch held at on.
2. Front tire rotating
Alternates
below 1.0
and 5
• Inspect METER IG 15
A fuse
• Inspect DSC HU/CM
• Inspect ABS (ABS /
TCS) HU/CM
(See
• Inspect related
harness
B
—
—
—
—
—
C
Brake switch on/off
Brake switch
Depress brake pedal
B+
• Inspect brake switch
• Inspect related
harness
Replace brake pedal
Below 1.0
D
—
—
—
—
—
E
O/D control
(ATX only)
PCM
Ignition switch at ON position
B+
• Inspect PCM
• Inspect related
harness
F
MTX
Clutch
switch on/off Clutch switch
Inspect for
continuity to
ground
Depress
crutch switch
Yes
• Inspect clutch switch
• Inspect related
harness
Other
No
ATX
Selector
lever
position
TR switch
Inspect for
continuity to
ground
Selector lever
at N or P
position
Yes
• Inspect TR switch
TRANSAXLE RANGE
(TR) SWITCH
INSPECTION
• Inspect starter
• Inspect related
harness
Other
No
G
Cruise set indicator
light output
Cruise set
indicator light
Ignition switch at ON position
B+
• Inspect METER IG 15
A fuse
• Inspect instrument
cluster
• Inspect related
harness
Ignition switch at LOCK
position or ACC position
Below 1.0
H
Cruise main
indicator light
output
Cruise main
indicator light
Under any condition: inspect
for continuity to ground
Yes
• Inspect instrument
cluster
• Inspect related
harness
I
Cruise actuator
ground
GND
Under any condition: inspect
for continuity to ground
Yes
• Inspect GND
A6E8128W013
T–112
CRUISE CONTROL SYSTEM
End Of Sie
ACTUATOR CABLE REMOVAL
A6E812866311W01
1. Remove the plug hole plate.
2. Remove the cover from the cruise actuator. (See
T–110 CRUISE ACTUATOR REMOVAL/INSTALLATION
3. Remove the installation nut and pull the cruise actuator toward you.
4. Move the throttle, and remove the end fitting of
the actuator cable from the throttle.
5. Squeeze the hooks of the grommet, and remove
the actuator cable.
J
Cruise control
switch position
Cruise control
switch
Inspect for
resistance
Cruise control
main switch
held at on
0 ohm
• Inspect cruise control
• Inspect related
harness
SET/COAST
switch held at
on
Approx. 680
ohms
RESUME/
ACCEL switch
held at on
Approx.
2200 ohms
CANCEL
switch held at
on
Approx. 120
ohms
K
Brake switch on/off
Brake switch 2
Ignition switch
at ON position
Depress brake
pedal
Below 1.0
• Inspect brake switch 2
• Inspect related
harness
Other
B+
L
IG1
METER IG 15 A
fuse
Ignition switch at ON position
B+
• Inspect METER IG 15
A fuse
• Inspect related
harness
Ignition switch at LOCK
position or ACC position
Below 1.0
Terminal
Signal
Connected to
Test condition
Voltage (V)
/Continuity
Action
A6E8128W007
CRUISE CONTROL SYSTEM
T–113
T
6. Remove the actuator cable from the bracket
7. Remove the end fitting of the actuator cable from
the cruise actuator.
8. Squeeze the hooks of the grommet, and remove
it from the cruise actuator.
9. Remove the actuator cable.
End Of Sie
A6E8128W004
A6E8128W005
A6E8128W008
T–114
CRUISE CONTROL SYSTEM
ACTUATOR CABLE INSTALLATION
A6E812866311W02
1. Slide the lock lever in the direction shown by the
arrow to unlock the adjuster.
2. Turn the ratchet ring to release lock in the
direction shown by the arrow.
3. Install the actuator cable to the cruise actuator.
Caution
• Due to the possibility of actuator cable
damage, make sure there is no twisting in
the cable when installing.
4. Install the cruise actuator. (See
5. Pass the actuator cable under the accelerator
cable.
6. Install the actuator cable to the bracket.
A6E8128W009
A6E8128W010
A6E8128W005
A6E8128W004
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст