Mazda 6. Manual — part 337
AUDIO AND NAVIGATION SYSTEM
T–107
T
CENTER ROOF ANTENNA REMOVAL/INSTALLATION
A6E812466939W01
1. Disconnect the negative battery cable.
2. Remove the headliner. (See
S–96 HEADLINER REMOVAL/INSTALLATION
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
5. After installation, verify that the rubber of the
center roof antenna is installed to the roof panel
with no space between them.
End Of Sie
CENTER ROOF ANTENNA INSPECTION
A6E812466939W02
1. Verify that there is no continuity between the
center roof antenna terminals A and C using an
ohmmeter.
2. Inspect for continuity between the center roof
antenna terminals using an ohmmeter.
• If not as specified, replace the center roof
antenna.
End Of Sie
GLASS ANTENNA INSPECTION
A6E812466931W01
1. Inspect the glass antenna for damage visually.
2. Inspect for continuity between the glass antenna
terminals using an ohmmeter.
• If not as specified, repair the glass antenna.
(See
.)
End Of Sie
1
Antenna rod
2
Antenna feeder
3
Nut
4
Center roof antenna
A6E8124W023
A6E8124W048
A6E8124W031
A6E8124W030
A6E8124W031
T–108
AUDIO AND NAVIGATION SYSTEM
GPS ANTENNA REMOVAL/INSTALLATION
A6E812466936W01
1. Disconnect the negative battery cable.
2. Remove the instrument cluster.
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
End Of Sie
ANTENNA FEEDER LOCATION
A6E812466941W01
.
End Of Sie
1
Connector
2
GPS antenna
A6E8124W022
A6E8124W038
1
Front antenna feeder
2
Rear antenna feeder No.1
3
Rear antenna feeder No.2
4
With center roof antenna
5
With glass antenna
AUDIO AND NAVIGATION SYSTEM
T–109
T
FRONT ANTENNA FEEDER INSPECTION
A6E812466941W02
1. Verify that there is no continuity between the front
antenna feeder terminals A and B using an
ohmmeter.
2. Inspect for continuity between the front antenna
feeder terminals using an ohmmeter.
• If not as specified, replace the instrument
panel harness.
End Of Sie
REAR ANTENNA FEEDER INSPECTION
A6E812466942W01
1. Verify that there is no continuity between antenna feeder terminals A and B using an ohmmeter.
2. Inspect for continuity between the antenna feeder terminals using an ohmmeter.
• If not as specified, replace the rear harness.
End Of Sie
A6E8124W039
A6E8124W047
A6E8124W042
A6E8124W047
T–110
CRUISE CONTROL SYSTEM
CRUISE ACTUATOR REMOVAL/INSTALLATION
A6E812866310W01
1. Disconnect the negative battery cable.
2. Remove in the order indicated in the table.
3. Install in the reverse order of removal.
Cover Removal Note
1. Unclamp the clips of the heater hoses at the front
of the cover.
End Of Sie
CRUISE ACTUATOR INSPECTION
A6E812866310W02
1. Disconnect the cruise actuator connector.
2. Measure the voltage, continuity and resistance at the cruise actuator terminals as indicated below.
• If not as specified, inspect the parts listed under “Action.”
• If the parts and wiring harnesses are okay but the system still does not work properly, replace the cruise
actuator.
CRUISE CONTROL SYSTEM
1
Cover
(See
2
Nut
3
Connector
4
Actuator cable
(See
)
(See
T–114 ACTUATOR CABLE INSTALLATION
)
5
Screw
6
Bracket
7
Cruise actuator
A6E8128W001
A6E8128W002
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст