Mazda 6. Manual — part 291
OUTSIDE MIRROR
S–59
S
Cover Disassembly Note
1. Pull off the mirror holder tab with a screwdriver
and press the mirror cover tab downward.
Outside Mirror Glass Assembly Note
1. Press the mirror into the base so that the pin does
not dislodge.
End Of Sie
POWER OUTSIDE MIRROR INSPECTION
A6E773269110W03
1. Disconnect the power outside mirror connector.
2. Apply battery positive voltage to the power
outside mirror terminals and inspect the operation
of the power outside mirror.
• If not as specified, replace the power outside
mirror.
3. Inspect for continuity between the power outside
mirror heater terminals.
• If not as specified, replace the power outside
mirror.
End Of Sie
A6E7732W004
A6E7732W005
Mirror operation
Terminal
B+
GND
Up
B
D
Down
D
B
Left
F
D
Right
D
F
A6E7732W007
A6E7732W009
A6E7732W010
S–60
OUTSIDE MIRROR
POWER OUTSIDE MIRROR SWITCH REMOVAL/INSTALLATION
A6E773266600W01
1. Disconnect the negative battery cable.
2. Remove the front door trim.
3. Remove the screws and the power outside mirror
switch.
4. Install in the reverse order of removal.
End Of Sie
POWER OUTSIDE MIRROR SWITCH INSPECTION
A6E773266600W02
1. Inspect for continuity between the power outside
mirror switch terminals using an ohmmeter.
• If not as specified, replace the power outside
mirror switch.
End Of Sie
A6E7732W008
A6E7732W001
A6E7734W003
REARVIEW MIRROR
S–61
S
REARVIEW MIRROR REMOVAL
A6E773469220W01
1. Insert a screwdriver between the mirror and the
base.
2. Push the base pin down to remove the rearview
mirror.
End Of Sie
REARVIEW MIRROR INSTALLATION
A6E773469220W02
1. Install the rearview mirror onto the base.
End Of Sie
BASE REMOVAL
A6E773469240W01
1. Remove the rearview mirror.
2. Wind each end of a wire around a bar.
Warning
• Using a SST (piano wire) with bare hands
can cause injury. Always wear gloves
when using a SST (piano wire).
Note
• Use a long sawing action to spread the work
over the whole length of the SST (piano
wire) to prevent it from breaking.
3. Saw through the sealant to remove the base.
End Of Sie
REARVIEW MIRROR
A6E7734W001
A6E7734W002
A6E7734W006
S–62
REARVIEW MIRROR
BASE INSTALLATION
A6E773469240W02
1. Cut away all of the original sealant using a razor.
2. Clean and degrease the ceramic coating on the glass and the base.
3. Apply primer to the bonding area of the glass and the base.
Caution
• Keep the area free of dirt and grease, and do not touch the surface or the primer may not properly
bond to the surface of the glass.
4. Apply a height of 3.0 mm {0.12 in} sealant to the
base.
Note
• Use only glass primer on the glass, and
body primer on the base. Allow the primer to
dry for approximately 30 minutes.
5. Center the base in the ceramic coating and press
it onto the glass.
6. Use isopropyl alcohol to remove any excess
repair sealant.
Hardening time of sealant
7. Install the rearview mirror.
End Of Sie
Temperature
Surface
hardening time
Time required
until vehicle can
be put into
service
5
°C {41 °F}
Approx. 1.5 h
Approx. 12 h
20
°C {68 °F}
Approx. 1 h
Approx. 4 h
35
°C {95 °F}
Approx. 10 min.
Approx. 2 h
A6E7734W004
A6E7734W005
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст