Mazda 6. Manual — part 290
MOLDING
S–55
S
FRONT BELTLINE MOLDING REMOVAL
A6E773050640W01
Note
• When removing the front beltline molding, the clip may be damaged. If the clip is damaged, replace it with
a new one.
1. Pull the A section upward and remove the clip.
2. Rotate the B section of the front beltline molding
in direction (2), along the direction (1) shown in
the figure and remove it from the body.
End Of Sie
FRONT BELTLINE MOLDING INSTALLATION
A6E773050640W02
1. Press the clip into the body.
2. Press in the B section of the front beltline molding
along the direction (1) shown in the figure to
attach it to the body.
Note
• If the front beltline molding is difficult to
attach, apply soapy water.
End Of Sie
MOLDING
A6E7730W001
A6E7730W003
S–56
MOLDING
REAR BELTLINE MOLDING REMOVAL
A6E773050660W01
Note
• When removing the rear beltline molding, the clip may be damaged. If the clip is damaged, replace it with
a new one.
1. Pull the A section upward and remove the clip.
2. Rotate the B section of the front beltline molding
in direction (2), along the direction (1) shown in
the figure and remove it from the body.
3. Pull the C section upward and remove the clip.
Then remove the front beltline molding.
End Of Sie
REAR BELTLINE MOLDING INSTALLATION
A6E773050660W02
1. Press the clip at the C section into the body.
2. Press in the B section of the rear beltline molding
along the direction (1) to attach it to the body.
3. Press the clip at the A section in and attach the
rear beltline molding.
Note
• If the rear beltline molding is difficult to
attach, apply soapy water.
End Of Sie
A6E7730W004
A6E7730W005
MOLDING
S–57
S
ROOF MOLDING REMOVAL
A6E773050620W01
1. Detach the clips which secure A and B sections of
roof molding, using a screwdriver or equivalent
tool.
2. While pulling the roof molding up, detach the fit
for the T stat of the A section and the roof molding
and then remove the roof molding.
End Of Sie
ROOF MOLDING INSTALLATION
A6E773050620W02
1. Attach the roof molding to the T stud at the A
section.
2. Press in the roof molding along the direction (1)
shown in the figure and attach it to the clip A at
the B section.
3. Hook the roof molding to the clip B at the C
section, press it in, and attach the roof molding to
the clip B.
4. Press the roof molding along the direction (2)
shown in the figure and attach it to the clip A at
the B section.
5. Attach the roof molding to the T stud at the D
section.
End Of Sie
A6E7730W007
A6E7730W006
S–58
OUTSIDE MIRROR
POWER OUTSIDE MIRROR REMOVAL/INSTALLATION
A6E773269110W01
1. Disconnect the negative battery cable.
2. Remove the inner garnish.
3. Remove the front door trim.
4. Disconnect the power outside mirror connector.
5. Remove the screws and the mirror retention clips.
6. Remove the power outside mirror.
7. Install in the reverse order of removal.
End Of Sie
POWER OUTSIDE MIRROR DISASSEMBLY/ASSEMBLY
A6E773269110W02
1. Disassemble in the order indicated in the table.
2. Assemble in the reverse order of disassembly.
Outside Mirror Glass Disassembly Note
1. Press area A of the glass so that area B moves
toward you.
2. Insert a screwdriver into the notch and remove
the glass from the mirror base.
OUTSIDE MIRROR
A6E7732W006
1
Outside mirror glass
(See
S–58 Outside Mirror Glass Disassembly Note
(See
S–59 Outside Mirror Glass Assembly Note
)
2
Connector (with heated outside mirror)
3
Cover
(See
4
Outside mirror holder
A6E7732W002
A6E7732W003
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст