Mazda 6. Manual — part 225
M–10
REAR AXLE
WHEEL HUB, HUB SPINDLE REMOVAL/INSTALLATION
A6E631405000W02
Caution
• Performing the following procedures without first removing the ABS wheel-speed sensor may
possibly cause an open circuit in the harness if it is pulled by mistake. Before performing the
following procedures, remove the ABS wheel-speed sensor (body side) and fix it to an appropriate
place where the sensor will not be pulled by mistake while the vehicle is being serviced.
1. Remove in the order indicated in the table.
2. Install in the reverse order of removal.
.
Locknut Removal Note
1. Knock the crimped portion of the locknut outward
using a small cape chisel and a hammer.
2. Lock the hub by applying the brakes.
3. Remove the locknut.
A6E0312W078
1
Hub cap
2
Locknut
(See
)
(See
M–11 Locknut Installation Note
3
Parking brake cable
4
Brake caliper component
5
Disc plate
(See
6
Wheel hub component
7
Wheel hub
8
Hub bolt
(See
(See
M–7 Hub Bolt Installation Note
)
9
ABS sensor rotor (with ABS)
(See
M–11 ABS Sensor Rotor Removal Note
(See
M–11 ABS Sensor Rotor Installation Note
10
Dust cover
11
Hub spindle
A6E0312W021
REAR AXLE
M–11
M
ABS Sensor Rotor Removal Note
Note
• The sensor rotor does not need to be removed unless it is being replaced.
1. Remove the sensor rotor using a chisel.
ABS Sensor Rotor Installation Note
Caution
• Position the SST so that marking B faces the bottom.
1. Set the SST as shown in the figure.
2. Press on the new sensor rotor using the SST and
a press.
Locknut Installation Note
1. Install a new locknut and stake it as shown.
End Of Sie
A6E6314W001
A6E0313W011
A6E0313W012
A6E0313W013
M–12
DRIVE SHAFT
JOINT SHAFT PRE-INSPECTION
A6E631625700W01
1. Verify that the joint shaft is not twisted or cracked.
• Replace it as necessary.
2. Turn the joint shaft by hand and verify that the
bearing rotates smoothly and freely.
• Replace it as necessary.
End Of Sie
JOINT SHAFT REMOVAL/INSTALLATION
A6E631625700W02
Caution
• Performing the following procedures without first removing the ABS wheel-speed sensor may
possibly cause an open circuit in the harness if it is pulled by mistake. Before performing the
following procedures, remove the ABS wheel-speed sensor and fix it to an appropriate place
where the sensor will not be pulled by mistake while the vehicle is being serviced.
1. Drain the transaxle oil. (See
K–13 AUTOMATIC TRANSAXLE FLUID (ATF) REPLACEMENT
.)
2. Remove the ABS sensor. (See
P–32 FRONT ABS WHEEL-SPEED SENSOR REMOVAL/INSTALLATION
.)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
.
DRIVE SHAFT
A6E0313W015
A6E0313W016
DRIVE SHAFT
M–13
M
Brake Caliper Component Removal Note
1. Suspend the caliper aside with wire.
Wheel Hub, Steering Knuckle and Drive Shaft Removal Note
Caution
• The sharp edges of the joint shaft can slice or puncture the oil seal. Be careful when removing the
joint shaft from the transaxle.
1. Pull the joint shaft straight out.
2. Install the SST into the transaxle to hold the side
gears after the joint shaft is removed.
1
N–11 Tie-rod End Ball Joint Removal Note
2
bolt
3
Lower arm (front, rear) ball joint
(See
)
)
4
Stabilizer control link
5
M–13 Brake Caliper Component Removal
6
Disk plate
(See
)
7
Wheel hub, steering knuckle and drive shaft
(See
M–13 Wheel Hub, Steering Knuckle and Drive
8
Joint shaft bracket bolt
9
Joint shaft
10
Clip
(See
)
A6E0313W056
A6E0313W019
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст