Mazda CX 7. Manual — part 382
GLASS/WINDOWS/MIRRORS
09-12–15
09-12
DOOR GLASS POSITION CHANGE PROCEDURE
id091200803600
Note
• After performing the following procedure, verify that the two-step down function operates normally and the
door glass position has changed. If the two-step down function does not operate or the door glass position
has not changed, the procedure was not performed properly. Repeat the procedure from the beginning.
End Of Sie
WM: WINDOW GLASS
Start
1.
Turn the ignition switch to ON position.
2.
Perform auto close once.
3.
Perform auto open two times.
4.
Perform auto close three times.
Note
The door glass is fully closed when the above
procedure is completed.
Start the following procedure within 43 s.
Door glass position change completed.
1. Turn the ignition switch to ON position.
2. Perform auto close once.
3.
Perform auto open two times.
4.
Perform auto close three times.
Start the following procedure within 43 s.
Perform within 5 s.
Turn the ignition switch to OFF position.
1. Turn the ignition switch to ON position.
2. Adjust the door glass position from the fully closed position by
moving the power window main switch up or down.
(Approximately 20
—
100 mm {0.79
—
3.40 in})
Note
The door glass position from the fully closed position is the
change in distance.
The change in distance is approx. 20 mm {0.79 in} when
the door glass is opened less than 20 mm {0.79 in}, and
approximately 100 mm {3.40 in} when the door glass is
opened more than 100 mm {3.40 in}.
3. Turn the ignition switch to OFF position.
Perform within 5 s.
Note
The two-step down function will not operate during the
following procedure:
acxuuw00001671
GLASS/WINDOWS/MIRRORS
09-12–16
WINDSHIELD REMOVAL
id091200801300
1. Disconnect the negative battery cable.
2. Remove the following parts:
(1) Windshield wiper arm and blade (See 09-19-3 WINDSHIELD WIPER ARM AND BLADE REMOVAL/
INSTALLATION.)
(2) Cowl grille (See 09-16-11 COWL GRILLE REMOVAL/INSTALLATION.)
(3) Rearview mirror (See 09-12-35 REARVIEW MIRROR REMOVAL.)
(4) Sunvisor (See 09-17-26 SUNVISOR REMOVAL/INSTALLATION.)
(5) Map light (See 09-18-22 MAP LIGHT REMOVAL/INSTALLATION.)
(6) A-pillar trim (See 09-17-15 A-PILLAR TRIM REMOVAL/INSTALLATION.)
(7) Assist handle (See 09-17-27 ASSIST HANDLE REMOVAL/INSTALLATION.)
3. Set the headliner out of the way.
4. Apply protective tape along the edge of the body.
Note
• Overlap and adhere the protective tape to
the corners to prevent damage.
5. Remove the windshield molding by pulling it
outward.
Note
• If the windshield molding is difficult to
remove, warm the windshield molding using
a hot air blower.
• The windshield molding is a replacement
part.
Not Reusing Windshield
Note
• For the areas of the sealant that are difficult to cut, use the piano wire and follow the procedure under
“Reusing Windshield”.
1. Cut out the sealant all around the glass using a
sealant remover.
2. Remove the windshield.
PROTECTIVE TAPE
A
A
GLASS SIDE
BODY SIDE
SEC. A—A
acxuuw00001530
49 G050 1A0
SEALANT
REMOVER
acxuuw00001522
GLASS/WINDOWS/MIRRORS
09-12–17
09-12
Reusing Windshield
Warning
• Using the piano wire with bare hands can cause injury. Always wear gloves when using the piano
wire.
Note
• Before removing the windshield from the body, mark the position of the windshield by affixing tape to the
windshield and body panel.
1. Avoiding the pin on the inside of the vehicle, insert
the piano wire which has been cut to sufficient
length.
2. Wind each end of the piano wire around a bar.
Note
• Use a long sawing action to spread the work
over the whole length of the piano wire to
prevent it from breaking due to localized
heating.
3. Secure one end of the piano wire, and while
pulling the other end, cut the sealant around the
windshield.
4. Pinch the pin from the inside of the vehicle and
detach it.
5. Remove the windshield.
6. If the pin is damaged, remove the pin.
Note
• Before removing the pin from the windshield
glass, place an alignment mark on the
windshield.
End Of Sie
WINDSHIELD INSTALLATION
id091200801400
Warning
• Using a razor with bare hands can cause injury. Always wear gloves when using a razor.
Caution
• If a door is opened or closed when all the window glass is closed, the resulting change in air
pressure could cause the sealant to crack preventing the proper installation of the glass. Keep the
door glass opened until the windshield installation is completed.
1. Remove the sealant along the perimeter of the glass using a cutting a razor. (When reusing the glass)
2. Clean and degrease an approx. 50 mm {1.97 in} wide strip along the perimeter of the windshield.
3. Inspect the glass for cracks. If it is cracked, chamfer it using sandpaper.
PIN
PIN
acxuuw00001531
SEALANT
PROTECTIVE TAPE
PIANO WIRE
acxuuw00001532
PIANO WIRE
acxuuw00001524
GLASS/WINDOWS/MIRRORS
09-12–18
4. Align the marks made before removal and install
the pin to the windshield referring to the figure.
(when reusing the glass, and the pin was
removed)
5. Install the windshield molding.
6. Use glass primer on the glass, then allow it to dry
for approx. 30 min.
Caution
• To prevent weakening of the primer
adhesion, keep the bonding surface free
of dirt, moisture, and grease. Do not
touch the surface with your hand.
Note
• Make sure to apply primer to the hollowed
marks in the ceramic coating.
7. Cut away the old sealant using a razor or scraper
so that 1— 2 mm {0.04— 0.07 in} thickness of
sealant remains along the perimeter of the frame.
8. If the sealant has come off completely in any one
place, apply some primer after degreasing, and
allow it approx. 30 min to dry. Then apply 2 mm
{0.08 in} thickness of new sealant.
Caution
• To prevent weakening of the primer
adhesion, keep the bonding surface free
of dirt, moisture, and grease. Do not
touch the surface with your hand.
A
A
HOLLOWED MARK IN THE
CERAMIC COATING
PIN
SEC. A—A
mm {in}
acxuuw00001540
A
A
SEC. A—A
WINDSHIELD MOLDING
acxuuw00001541
A
C
C
B
B
A
PRIMER
SEC. A—A
SEC. B—B
SEC. C—C
9.5 {0.37 }
9.5 {0.37 }
9.5 {0.37 }
mm {in}
acxuuw00001542
acxuuw00001543
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст