Mazda CX 7. Manual — part 380

GLASS/WINDOWS/MIRRORS

09-12–7

09-12

10. Remove the rear power window regulator through

the speaker installation hole.

11. Install in the reverse order of removal.

Caution

• Make sure the cable does not unspool

from the drum housing when installing.

End Of Sie

WM: WINDOW MOTOR

POWER WINDOW MOTOR REMOVAL/INSTALLATION

id091200803700

1. Fully lower the rear door glass.
2. Disconnect the negative battery cable.
3. Remove the following parts:

Front door

• Inner garnish (See.09-17-20 INNER GARNISH REMOVAL/INSTALLATION)

• Front door trim (See.09-17-20 FRONT DOOR TRIM REMOVAL/INSTALLATION)

Rear door

• Sail garnish (See.09-17-12 SAIL GARNISH REMOVAL/INSTALLATION)

• Rear door trim (See.09-17-23 REAR DOOR TRIM REMOVAL/INSTALLATION)

4. Remove the bolts.
5. Remove the power window motor from the power

window regulator.

6. Disconnect the power window motor connector.
7. Install in the reverse order of removal.

Note

• When installing the power window motor to

the power window regulator drum, the drum
housing tabs may detach from the door
module. If this happens, insert a hand
through the speaker installation hole to
engage the drum housing tabs, and install
the power window motor to the drum while
supporting the drum housing.

End Of Sie

POWER WINDOW MOTOR INSPECTION

id091200800800

Front Side

1. Apply battery positive voltage and connect the

ground to power window motor terminals E and F,
and then inspect the power window motor
operation.

• If the power window motor does not operate

as indicated in the table, replace it.

Caution

• If the power window motor temperature is

high, the motor may not rotate due to the
motor internal bimetal function. Leave it
untouched for about 3 min to cool it
down, then reinspect.

2. Connect the battery positive voltage to power window motor terminal D and connect terminal C to ground.
3. Operate the power window motor and measure the voltage at terminals A and B.

• If there is any malfunction, replace the power window motor.

Voltage

• Pulse: max. 12 V/min. 0 V

REAR POWER WINDOW
REGULATOR

acxuuw00001471

POWER WINDOW
MOTOR

POWER WINDOW
MOTOR CONNECTOR

6.2—8.2 N·m
{64—83 kgf·cm,
55—72 in·lbf}

BOLT

acxuuw00001506

Operation

Terminal

F

E

Open

B+

Ground

Close

Ground

B+

F

A

C

E

B

D

F

M

E

B

A

D

C

acxuuw00001507

GLASS/WINDOWS/MIRRORS

09-12–8

Rear Side

1. Apply battery positive voltage and connect the

ground to the power window motor terminals, and
then inspect the power window motor operation.

• If the power window motor does not operate

as indicated in the table, replace it.

Caution

• If the power window motor temperature is

high, the motor may not rotate due to the
motor internal bimetal function. Leave it
untouched for about 3 min to cool it
down, then reinspect.

End Of Sie

WM: WINDOW SWITCH

POWER WINDOW MAIN SWITCH REMOVAL/INSTALLATION

id091200801900

1. Disconnect the negative battery cable.
2. Remove the inner garnish. (See 09-17-20 INNER GARNISH REMOVAL/INSTALLATION.)
3. Remove the front door trim. (See 09-17-20 FRONT DOOR TRIM REMOVAL/INSTALLATION)
4. Disconnect the power door mirror switch connector and the power window main switch connector.
5. Remove the screws, then the power window main

switch.

6. Install in the reverse order of removal.

End Of Sie

POWER WINDOW MAIN SWITCH INSPECTION

id091200802000

Note

• Before proceeding with diagnosis of malfunctioning power windows, ensure the POWER WINDOW

INITIALIZATION PROCEDURE has been performed.

Driver’s Side

1. Measure the voltage at each terminal (other than terminals 1M and 2A).

• If the voltage is not as specified in the Terminal Voltage Table, inspect the parts under “inspection item(s)”

and related wiring harnesses.

2. Disconnect the negative battery cable.
3. Inspect the power window main switch connector for continuity at terminal 1M and 2A.
4. If the system does not work properly even though

the inspection items or related wiring harnesses
do not have any malfunction, replace the power
window main switch.

Operation

Terminal

F

E

Open

B+

Ground

Close

Ground

B+

M

*

*

E

*

*

F

F

E

acxuuw00001511

SCREW

POWER WINDOW
MAIN SWITCH

acxuuw00001170

POWER WINDOW MAIN SWITCH

HARNESS-SIDE CONNECTOR

1I

1M

1N

1K

1C

1A

1B

1D

1F

1E

1L

2A

2B

2C

2D

1G

1H

1J

acxuuw00001261

GLASS/WINDOWS/MIRRORS

09-12–9

09-12

Terminal

Signal name

Connected to

Measured condition

Voltage (V)/

Continuity

Inspection item (s)

1C

ACC

MIRROR 7.5 A

Ignition switch is at ACC
position

B+

• Inspect MIRROR 7.5 A

fuse

• Related wiring

harnesses

Ignition switch is at LOCK
position

1.0 or less

1E

IG 1

IG KEY1 15 A fuse

Ignition switch is at ON
position

B+

• Inspect IG KEY1 15 A

fuse

• Related wiring

harnesses

Ignition switch is at LOCK
position

1.0 or less

1F

Power-cut

signal

Power window

subswitch

Ignition switch at ON and
power-cut switch at UNLOCK

B+

• Power window

subswitch(See09-12-11
POWER WINDOW
SUBSWITCH
INSPECTION)

• Related wiring

harnesses

1G

Communicati

on

Power window

subswitch

—

—

—

1H

Communicati

on

BCM

—

—

—

1I

Close output

Power window motor

While door glass is opening

1.0 or less

• Power window motor

(See09-12-7 POWER
WINDOW MOTOR
INSPECTION.)

• Related wiring

harnesses

While door glass is closing

B+

1K

Open output

Power window motor

While door glass is opening

B+

• Power window motor

(See09-12-7 POWER
WINDOW MOTOR
INSPECTION.)

• Related wiring

harnesses

While door glass is closing

1.0 or less

1M

GND

Body ground

Under any condition: Inspect
for continuity to ground

Continuity

detected

• GND

1N

Power supply

P/W 30 A fuse

Under any condition

B+

• P/W 30 A fuse

• Related wiring

harnesses

2A

Sensor

ground

Power window motor

Under any condition: inspect
for continuity to ground

Continuity

detected

• Power window motor

(See09-12-7 POWER
WINDOW MOTOR
INSPECTION.)

• Related wiring

harnesses

2B

Power supply

Power window motor

While IG ON or IG OFF timer
works

B+

• Power window motor

(See09-12-7 POWER
WINDOW MOTOR
INSPECTION.)

• Related wiring

harnesses

2C

Pulse 1

Power window motor

Door glass is not in motion

0 or B+

• Power window motor

(See09-12-7 POWER
WINDOW MOTOR
INSPECTION.)

• Related wiring

harnesses

Door glass is in motion

Alternates

between 0

and B+

2D

Pulse 2

Power window motor

Door glass is in motion

Alternates

between 0

and B+

• Power window motor

(See09-12-7 POWER
WINDOW MOTOR
INSPECTION.)

• Related wiring

harnesses

Door glass is not in motion

0 or B+

GLASS/WINDOWS/MIRRORS

09-12–10

Rear Side

1. Remove the power window main switch. (See09-12-8 POWER WINDOW MAIN SWITCH REMOVAL/

INSTALLATION.)

2. When inspecting the rear, turn the power-cut switch UNLOCK.
3. Inspect for continuity between the power window main switch terminals.

• If not as specified, replace the power window main switch.

End Of Sie

1B

1M

1L

1J

Rear right

Switch position

Terminal

: Continuity

CLOSED

OFF

OPEN

1B

1A

1D

1M

Rear left

Switch position

Terminal

: Continuity

CLOSED

OFF

OPEN

REAR RIGHT

REAR LEFT

P/W CM

CLOSE

OPEN

AU

T

O

CLOSE

OPEN

AU

T

O

PO

WER-CUT

SWITCH

CONJUNCTION

CIRCUIT

CLOSE
RELAY

OPEN
RELAY

CLOSE

OPEN

CLOSE

OPEN

1A

2B

2D

1M

1N

1E

1H

1D

1J

1K

1L

1I

2C

2A

1C

1B

1F

1G

1I

1M

1N

1K

2B 2A

2C

1L

2D

1J

1A

1E

1F

1C

1D 1B

1G

1H

acxuuw00001301