Mazda CX 7. Manual — part 166
REAR SUSPENSION
02-14–5
02-14
Nut Removal Note
1. Support the rear axle with the jack.
2. Remove the service hole cover on the trunk side
trim.
3. Remove the nuts.
End Of Sie
REAR SHOCK ABSORBER INSPECTION
id021400801400
1. Inspect the rear shock absorber in the same way as the front shock absorber. (See 02-14-5 REAR SHOCK
ABSORBER INSPECTION.)
End Of Sie
REAR SHOCK ABSORBER DISPOSAL
id021400801500
1. Dispose the rear shock absorber in the same way as the front shock absorber. (See 02-14-5 REAR SHOCK
ABSORBER DISPOSAL.)
End Of Sie
WM: REAR COIL SPRING
JACK
acxuuw00001975
SERVICE HOLE
COVER
acxuuw00001719
1871-1U-06B(02-14).fm 5 ページ 2006年3月15日 水曜日 午前11時1分
REAR SUSPENSION
02-14–6
REAR COIL SPRING REMOVAL/INSTALLATION
id021400800700
1. Remove the middle pipe. (See 01-15-2 EXHAUST SYSTEM REMOVAL/INSTALLATION[L3 WITH TC].)
2. Remove the rear stabilizer. (See 02-14-11 REAR STABILIZER REMOVAL/INSTALLATION.)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
5. Inspect the rear wheel alignment. (See 02-11-4 REAR WHEEL ALIGNMENT.)
.
Bolt (Rear Lower Arm Outer Side) Removal Note
1. Raise the rear trailing link to the unloaded
condition with a jack.
2. Loosen the inner and outer bolts of the lateral link.
3. Loosen the outer bolt of the upper arm.
C
C
B
A
B
A
2
1
3
75.5—102
{7.70—10.4, 55.7—75.2}
N·m {kgf·m, ft·lbf}
acxuuw00001681
1
Bolt (rear lower arm outer side)
(See 02-14-6 Bolt (Rear Lower Arm Outer Side)
Removal Note)
2
Rear coil spring
(See 02-14-7 Rear Coil Spring Installation Note)
3
Upper spring seat rubber
JACK
acxuuw00001976
1871-1U-06B(02-14).fm 6 ページ 2006年3月15日 水曜日 午前11時1分
REAR SUSPENSION
02-14–7
02-14
4. Support the lower arm with a jack.
5. Loosen the inner bolt of the lower arm.
6. Remove the outer bolt of the lower arm.
7. Jack down slowly and remove the coil spring.
Warning
• Removing the coil spring is dangerous.
The coil spring could fly off, the cause
serious injury or death.
Rear Coil Spring Installation Note
1. Position the jack under the lower arm and jack up slowly.
Warning
• Installing the coil spring is dangerous. The coil spring could fly off, and cause serious injury or
death.
2. Install the lower arm (outer side) bolt.
3. Raise the rear trailing link to the unloaded condition with a jack.
4. Tighten the outer bolt of the upper arm.
Tightening torque
• 75.5— 102 N·m {10.0— 12.2 kgf·m, 72.3— 75.2 ft·lbf}
5. Tighten the inner and outer bolts of the lateral link.
Tightening torque
• 75.5— 102 N·m {10.0— 12.2 kgf·m, 72.3— 75.2 ft·lbf}
End Of Sie
WM: REAR LOWER ARM
JACK
acxuuw00002442
1871-1U-06B(02-14).fm 7 ページ 2006年3月15日 水曜日 午前11時1分
REAR SUSPENSION
02-14–8
REAR LOWER ARM REMOVAL/INSTALLATION
id021400800900
1. Remove the middle pipe. (See 01-15-2 EXHAUST SYSTEM REMOVAL/INSTALLATION[L3 WITH TC].)
2. Remove the rear stabilizer. (See 02-14-11 REAR STABILIZER REMOVAL/INSTALLATION.)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
5. Inspect the rear wheel alignment. (See 02-11-4 REAR WHEEL ALIGNMENT.)
.
End Of Sie
WM: REAR LATERAL LINKS
REAR LATERAL LINK REMOVAL/INSTALLATION
id021400801200
1. Raise the rear trailing link to the unloaded
condition with a jack.
Note
• Jacking up the rear suspension to the no-
occupant position will lighten the force on the
bushing and make it easier to perform the
procedure.
A
A
B
B
3
1
2
4
80—100
{8.16—10.1, 60.0—73.7}
75.5—102
{7.70—10.4,
55.7—75.2}
N·m {kgf·m, ft·lbf}
acxuuw00001682
1
Rear coil spring component
(See 02-14-6 REAR COIL SPRING REMOVAL/
INSTALLATION.)
2
Bolt (rear lower arm inner side)
3
Rear lower arm
4
Bound stopper
JACK
acxuuw00001977
1871-1U-06B(02-14).fm 8 ページ 2006年3月15日 水曜日 午前11時1分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст