Mazda CX 7. Manual — part 167
REAR SUSPENSION
02-14–9
02-14
2. Remove the rear lateral link.
3. Install the rear lateral link shown in the figure.
4. Inspect the rear wheel alignment. (See 02-11-4
REAR WHEEL ALIGNMENT.)
End Of Sie
WM: REAR UPPER ARM
75.5—102
{7.70—10.4,
55.7—75.2}
N·m {kgf·m, ft·lbf}
REAR LATERAL LINK
acxuuw00001684
FRONT
FRONT
A
A
SECTION A-A
acxuuw00001685
1871-1U-06B(02-14).fm 9 ページ 2006年3月15日 水曜日 午前11時1分
REAR SUSPENSION
02-14–10
REAR UPPER ARM REMOVAL/INSTALLATION
id021400800800
1. Raise the trailing link to the unloaded condition
with the jack.
Note
• Jacking up the rear suspension to the no-
occupant position will lighten the force on the
bushing and make it easier to perform the
procedure.
2. Remove the rear upper arm.
3. Install the rear upper arm.
4. Inspect the rear wheel alignment. (See 02-11-4 REAR WHEEL ALIGNMENT.)
End Of Sie
WM: REAR STABILIZER
JACK
acxuuw00001978
75.5—102
{7.70—10.4,
55.7—75.2}
N·m {kgf·m, ft·lbf}
REAR UPPER ARM
acxuuw00001683
1871-1U-06B(02-14).fm 10 ページ 2006年3月15日 水曜日 午前11時1分
REAR SUSPENSION
02-14–11
02-14
REAR STABILIZER REMOVAL/INSTALLATION
id021400800500
1. Remove in the order indicated in the table.
2. Install in the reverse order of removal.
.
Rear Stabilizer Installation Note
1. Install the rear stabilizer so that the side with the
wider marking area points towards the right side
of the vehicle.
43.1—60.8
{4.40—6.19,
31.8—44.8}
43.1—60.8
{4.40—6.19,
31.8—44.8}
43.1—60.8
{4.40—6.19,
31.8—44.8}
N·m {kgf·m, ft·lbf}
RUBBER
GREASE
GREASEGREASE
3
4
1
2
acxuuw00001686
1
Stabilizer control link
(See 02-14-12 Stabilizer Control Link Installation
Note.)
2
Stabilizer bracket
3
Bushing
(See 02-14-12 Bushing Installation Note.)
4
Rear stabilizer
(See 02-14-11 Rear Stabilizer Installation Note.)
FRONT
MARKING
RH
LH
20
10
acxuuw00001795
1871-1U-06B(02-14).fm 11 ページ 2006年3月15日 水曜日 午前11時1分
REAR SUSPENSION
02-14–12
Bushing Installation Note
1. Align the outer side of the marking with the
stabilizer bushing.
Stabilizer Control Link Installation Note
1. Install the control link with white marking to the
left side of the vehicle.
End Of Sie
WM: STABILIZER CONTROL LINK (FRONT/REAR)
STABILIZER CONTROL LINK INSPECTION
id021400800300
1. Remove the stabilizer control link from the vehicle. (See 02-14-11 REAR STABILIZER REMOVAL/
INSTALLATION.)
2. Inspect for bending and damage.
3. Measure the ball joint starting torque.
(1) Rock the ball joint stud side to side 10 times.
(2) Rotate the ball joint stud 10 times.
(3) Measure the starting torque using a suitable
Allen socket and a torque wrench.
Rear stabilizer control link ball joint starting
torque
0.2— 0.8 N·m {2.1— 8.1 kgf·cm, 1.8— 7.0
in·lbf}
End Of Sie
WM: REAR TRAILING LINKS
TRAILING LINK REMOVAL/INSTALLATION[2WD]
id0214008001a1
Caution
• Performing the following procedures without first removing the ABS wheel-speed sensor may
possibly cause an open circuit in the harness if it is pulled by mistake. Before performing the
following procedures, remove the ABS wheel-speed sensor (axle side) and fix it to an appropriate
place where the sensor will not be pulled by mistake while servicing the vehicle.
1. Remove the middle pipe. (See 01-15-2 EXHAUST SYSTEM REMOVAL/INSTALLATION[L3 WITH TC].)
2. Remove the rear stabilizer. (See 02-14-11 REAR STABILIZER REMOVAL/INSTALLATION.)
3. Remove the rear coil spring. (See 02-14-6 REAR COIL SPRING REMOVAL/INSTALLATION.)
4. Remove in the order indicated in the table.
5. Install in the reverse order of removal.
6. Inspect the rear wheel alignment. (See 02-11-4 REAR WHEEL ALIGNMENT.)
RH
FRONT
MARKING
BUSHING
acxuuw00001796
LH
RH
WHITE MARKING
acxuuw00001797
ampjjw00002979
1871-1U-06B(02-14).fm 12 ページ 2006年3月15日 水曜日 午前11時1分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст