Mazda CX 7. Manual — part 272
POWER STEERING
06-14–5
06-14
10. Remove the SSTs. Install and tighten the pressure pipe to the specified torque.
Tightening torque
29.4— 44.1 N·m {3.0— 4.4 kgf·m, 22— 32 ft·lbf}
11. Bleed the air from the system.
End Of Sie
WM: STEERING WHEEL AND COLUMN
STEERING WHEEL AND COLUMN INSPECTION
id061400800300
Steering Wheel Play Inspection
1. With the wheels in the straight-ahead position, gently turn the steering wheel to the left and right and verify that
the play is within the specification.
• If the play exceeds the specification, either the steering joints are worn or the backlash of the steering gear
is excessive. Correct as necessary.
Steering wheel play
0— 30 mm {0— 1.18 in}
Steering Wheel Looseness Inspection
1. Move the steering wheel as shown in the figure to
inspect for column bearing wear, steering shaft
joint play, steering wheel looseness, and column
looseness.
• Repair or replace as necessary.
Steering Wheel Effort Inspection
1. Inspect the following points:
• Tire size and tire pressure
• Fluid level
• Drive belt deflection
2. With the vehicle on a hard, level surface, put the wheels in the straight-ahead position.
3. Remove the air bag module.
Warning
• Handling the air bag module improperly can accidentally deploy the air bag module, which may
seriously injure you. Read AIR BAG SYSTEM WARNINGS before handling the air bag module. (See
08-10-3 AIR BAG SYSTEM SERVICE WARNINGS.) (See 08-10-5 AIR BAG SYSTEM SERVICE
CAUTIONS.)
4. Start the engine and warm the power steering fluid to 50— 60
°C {122— 140 °F}.
5. Measure the steering wheel effort using a torque
wrench.
• If not within the specification, verify the
following:
— No air in steering system
— No fluid leakage at hose or connectors
— Function of oil pump and steering gear
Steering wheel effort (reference value)
7.8 N·m {80 kgf·cm, 69 in·lbf} max.
Note
• To determine whether the steering effort is
satisfactory or not, perform the inspection on
another vehicle of the same model and under the same conditions, and compare the results.
• The steering wheel effort varies with conditions as shown below.
— Road conditions, such as dry or wet, and asphalt or concrete.
— Tire conditions, such as brand, wear, and tire pressure.
acxuuw00002353
acxuuw00002354
1871-1U-06B(06-14).fm 5 ページ 2006年3月15日 水曜日 午前11時25分
POWER STEERING
06-14–6
End Of Sie
STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION
id061400800400
Warning
• Handling the air bag module improperly can accidentally deploy the air bag module, which may
seriously injure you. Read AIR BAG SYSTEM WARNINGS before handling the air bag module. (See
08-10-3 AIR BAG SYSTEM SERVICE WARNINGS.) (See 08-10-5 AIR BAG SYSTEM SERVICE
CAUTIONS.)
1. Remove in the order indicated in the table.
2. Install in the reverse order of removal.
3. If the steering lock component of a vehicle equipped with the advanced keyless system is replaced, perform the
following procedure after installation.
• Without immobilizer system
— Steering lock unit programming (See 09-14-35 STEERING LOCK UNIT ID CODE
REGISTRATION[ADVANCED KEYLESS SYSTEM].)
• With immobilizer system
— Immobilizer system resetting (See 09-14-11 IMMOBILIZER SYSTEM COMPONENT REPLACEMENT/
KEY ADDITION AND CLEARING[ADVANCED KEYLESS SYSTEM].) (See 09-14-20 IMMOBILIZER
SYSTEM COMPONENT REPLACEMENT/KEY ADDITION AND CLEARING[KEYLESS ENTRY
SYSTEM].)
.
1
2
6
7
3
4
8
5
R
10
11
12
9
39.2
—
49.0
{4.0
—
4.9, 30
—
36}
15.7
—
22.5
{1.7
—
2.2,
11.6
—
16.5}
18.6
—
26.5
{1.9
—
2.7,
14
—
19}
N·m {kgf·m, ft·lbf}
R
8.8
—
12.8 N·m
{89.8
—
130.5 kgf·cm, 77.8
—
113.2 in·lbf}
13
acxuuw00000494
1
Air bag module
(See 08-10-6 DRIVER-SIDE AIR BAG MODULE
REMOVAL/INSTALLATION.)
2
Locknut
3
Steering wheel
(See 06-14-7 Steering Wheel Removal Note.)
(See 06-14-8 Steering Wheel Installation Note.)
4
Column cover
(See 09-17-8 COLUMN COVER REMOVAL/
INSTALLATION.)
5
Combination switch
(See 09-18-13 COMBINATION SWITCH
REMOVAL/INSTALLATION.)
6
Lower panel
(See 09-17-9 LOWER PANEL REMOVAL/
INSTALLATION.)
1871-1U-06B(06-14).fm 6 ページ 2006年3月15日 水曜日 午前11時25分
POWER STEERING
06-14–7
06-14
Steering Wheel Removal Note
Caution
• Do not try to remove the steering wheel by hitting the shaft with a hammer. The column will
collapse.
1. Set the vehicle in the straight-ahead position.
2. Remove the steering wheel using a suitable puller.
Steering Lock Mounting Bolts Removal Note
1. Make a groove in the heads of the steering lock
mounting bolts using a chisel and a hammer.
2. Remove the bolts using a screwdriver.
3. Disassemble the steering lock component.
Key Cylinder (Without Advanced Keyless System) Removal Note
1. Turn the key to the ACC position.
2. Push the pin and remove the outer cylinder.
Steering Lock Mounting Bolts Installation Note
1. Assemble the steering lock component to the steering shaft.
2. Verify that the lock operates correctly.
3. Install new steering lock mounting bolts.
4. Tighten the bolts until the heads break off.
7
Joint cover
8
Steering shaft
(See 06-14-8 Steering Shaft Installation Note.)
9
Dust cover
10
Steering lock mounting bolts
(See 06-14-7 Steering Lock Mounting Bolts
Removal Note.)
(See 06-14-7 Steering Lock Mounting Bolts
Installation Note.)
11
Steering lock component
12
Ignition switch
(See 09-21-2 IGNITION SWITCH REMOVAL/
INSTALLATION.)
13
Key cylinder (Without advanced keyless system)
(See06-14-7 Key Cylinder (Without Advanced
Keyless System) Removal Note.)
acxuuw00000495
PIN
acxuuw00001910
acxuuw00000496
1871-1U-06B(06-14).fm 7 ページ 2006年3月15日 水曜日 午前11時25分
POWER STEERING
06-14–8
Steering Shaft Installation Note
Caution
• Do not apply a shock in the axial direction of the shaft.
1. Lock the tilt lever.
2. Tighten nut A.
3. Tighten nut B.
4. Tighten bolt C.
Steering Wheel Installation Note
1. Make sure the wheels in the straight-ahead position, and install the steering wheel.
End Of Sie
WM: STEERING SHAFT
STEERING SHAFT INSPECTION
id061400800600
1. Inspect the following.
(1) Column bearing for damage
(2) Steering shaft length
• Replace the steering shaft component as
necessary.
Steering shaft length
211.6 mm {8.3 in}
2. Inspect the tilt and telescope operation.
(1) Verify that the adjusting lever moves smoothly
from unlock position to lock position.
(2) Verify that the steering shaft is fixed firmly
when the adjusting lever is locked.
• Replace the steering shaft component as
necessary.
End Of Sie
WM: STEERING GEAR AND LINKAGE
C
A
B
acxuuw00000497
E6U612ZW7013
LOCKED
UNLOCKED
ADJUSTING LEVER
B6U0612W008
1871-1U-06B(06-14).fm 8 ページ 2006年3月15日 水曜日 午前11時25分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст