Mazda CX 7. Manual — part 386
GLASS/WINDOWS/MIRRORS
09-12–31
09-12
FILAMENT INSPECTION
id091200801000
1. Turn the ignition switch to the ON position.
2. Turn the rear window defroster switch on.
Caution
• Directly touching the rear window
defroster filament with the lead of the
tester could damage it. Wrap aluminum
foil around the end of the lead and
inspect the filament by touching it with
the foil.
3. Connect the positive lead of the tester to the
positive side of each filament and the negative
lead to ground.
4. Gradually slide the positive lead from the positive
side to the negative side and verify that the
voltage decreases accordingly.
• If the voltage changes rapidly, the filament
has a malfunction. Repair the filament.
End Of Sie
FILAMENT REPAIR
id091200801100
1. Clean the filament using isopropyl alcohol.
2. Attach tape to both sides of the filament.
3. Using a small brush or marking pen, apply silver
paint.
4. After 2— 3 min, carefully remove the tape without
damaging the applied area.
Caution
• Do not operate the rear window defroster
until the paint is completely dry. It may
cause other malfunctions if it is used
before the paint is dry.
5. Dry the repaired part according to the following
procedure.
• When the room temperature is 25 °C {77 °F} ,
leave it as it is for 24 h.
• When a hot air blower is used, dry with the 150 °C {302 °F} air for 30 min.
End Of Sie
WM: OUTER MIRROR
Measured part
Voltage (Reference)
(1) to (2)
Approx. 11 V to 0 V
LEAD OF VOLTMETER
PUSH
ALUMINUM FOIL
FILAMENT
acxuuw00001514
POSITIVE
SIDE
NEGATIVE
SIDE
(1)
(2)
acxuuw00001515
SECTION TO BE REPAIRED
BROKEN FILAMENT
TAPE
acxuuw00001516
GLASS/WINDOWS/MIRRORS
09-12–32
POWER OUTER MIRROR REMOVAL/INSTALLATION
id091200802500
1. Disconnect the negative battery cable.
2. Remove the inner garnish. (See 09-17-20 INNER GARNISH REMOVAL/INSTALLATION.)
3. Remove the front door trim. (See 09-17-20 FRONT DOOR TRIM REMOVAL/INSTALLATION.)
4. Disconnect the power outer mirror connector.
5. Remove the bolts.
6. Push the power outer mirror against the vehicle
and detach the tab while lifting the mirror up to
remove.
7. Install in the reverse order of removal.
End Of Sie
OUTER MIRROR GLASS REMOVAL
id091200802600
1. Press area A of the mirror glass so that area B
moves outward.
2. Detach pin A while lifting up the inside of the
mirror glass holder.
3. Pull the mirror glass holder and remove pins B.
4. Disconnect the connectors. (vehicles with heated
outer mirrors)
5. Remove the mirror glass holder and the outer
mirror glass as a single unit.
End Of Sie
POWER OUTER MIRROR
CONNECTOR
TAB
BOLT
3.5—5.0 N·m
{36—50 kgf·cm,
31—44 in·lbf}
acxuuw00001657
OUTER MIRROR GLASS
A
B
acxuuw00001658
PIN A
PIN B
PIN B
MIRROR GLASS HOLDER
A
A
B
B
B
B
OUTER MIRROR
GLASS
CONNECTOR
acxuuw00001659
GLASS/WINDOWS/MIRRORS
09-12–33
09-12
OUTER MIRROR GLASS INSTALLATION
id091200802700
1. Connect the connectors. (vehicles with heated outer mirrors)
2. Press part A on the outer mirror glass and install
pin A
3. Press part B on the outer mirror glass and install
pins B.
End Of Sie
OUTER MIRROR GARNISH REMOVAL
id091200802800
1. Remove the outer mirror glass from the outer mirror. (See 09-12-32 OUTER MIRROR GLASS REMOVAL.)
2. Pinch the clip ends using pincers and detach the
clips by pushing them forward.
3. Grasp the upper side of the outer mirror garnish
and remove it by pulling it in the direction of the
arrow.
End Of Sie
OUTER MIRROR GARNISH INSTALLATION
id091200802900
1. Position the outer mirror garnish against the
mirror body in the direction of the arrow shown in
the figure, and insert the outer mirror garnish clips
(6 locations) into the mirror body.
2. Install the outer mirror garnish so that there are
no gaps around the component.
End Of Sie
PIN A
PIN B
PIN B
MIRROR GLASS HOLDER
A
A
B
B
B
B
OUTER MIRROR
GLASS
CONNECTOR
acxuuw00001660
MIRROR BODY
CLIP
OUTER MIRROR GARNISH
acxuuw00001661
MIRROR
BODY
CLIP
OUTER MIRROR
GARNISH
acxuuw00001663
GLASS/WINDOWS/MIRRORS
09-12–34
POWER OUTER MIRROR INSPECTION
id091200803000
1. Apply battery positive voltage to the power outer
mirror terminals and inspect the operation of the
power outer mirror.
• If not as specified, replace the power outer
mirror.
2. Inspect for continuity between the power outer
mirror heater terminals.
• If not as specified, replace the power outer
mirror.
End Of Sie
WM: MIRROR SWITCH
POWER OUTER MIRROR SWITCH REMOVAL/INSTALLATION
id091200802300
Note
• The power outer mirror switch is integrated with the power window main switch.
1. Disconnect the negative battery cable.
2. Remove the inner garnish. (See 09-17-20 INNER GARNISH REMOVAL/INSTALLATION.)
3. Remove the front door trim. (See 09-17-20 FRONT DOOR TRIM REMOVAL/INSTALLATION)
4. Disconnect the power door mirror switch connector and the power window main switch connector.
5. Remove the screws, then the power outer mirror
switch.
6. Install in the reverse order of removal.
End Of Sie
Mirror operation
terminal
B+
GND
Up
A
B
Down
B
A
Left
C
B
Right
B
C
B
C
A
M
M
LEFT/RIGHT
ADJUSTMENTMOTOR
UP/DOWN
ADJUSTMENT MOTOR
A
G
C
I
B
*
*
*
acxuuw00001664
G
I
A
G
C
I
B
*
*
*
acxuuw00001665
: Continuity
Mirror operation
Heater
Terminal
I
G
acxuuw00001666
SCREW
POWER OUTER
MIRROR SWITCH
acxuuw00002430
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст