Mazda CX 7. Manual — part 387
GLASS/WINDOWS/MIRRORS
09-12–35
09-12
POWER OUTER MIRROR SWITCH INSPECTION
id091200802400
1. Inspect for continuity between the power outer mirror switch terminals using an ohmmeter.
• If not as indicated in the table, replace the power outer mirror switch.
End Of Sie
WM: REARVIEW MIRROR
REARVIEW MIRROR REMOVAL
id091200806800
1. Insert a flathead screwdriver between the mirror
and the base.
2. Push the base pin down to remove the rearview
mirror.
End Of Sie
: Continuity
OPERATION
UP
LH
RH
DOWN
LEFT
RIGHT
UP
DOWN
LEFT
RIGHT
3D
3F
3G
3H
1C
1M
3B
acxuuw00001655
*
*
*
3B
3D
3F
3G
3H
3B
3H
3G
3F
3D
1C
1M
1I
1M
1N
1K
1L
1J
1A
1E
1F
1C
1D 1B
1G
1H
LH
RH
POWER OUTER MIRROR
SWITCH
UP
DOWN
LEFT
RIGHT
MIRROR GLASS
ADJUSTMENT SWITCH
LEFT/RIGHT SELECTION
SWITCH
acxuuw00002228
BASE
BASE PIN
BASE
REARVIEW MIRROR
acxuuw00001667
GLASS/WINDOWS/MIRRORS
09-12–36
REARVIEW MIRROR INSTALLATION
id091200806700
1. Install the rearview mirror onto the base.
End Of Sie
BASE REMOVAL
id091200803200
1. Remove the rearview mirror. (See 09-12-35 REARVIEW MIRROR REMOVAL.)
2. Wind each end of a wire around a bar.
Warning
• Using the piano wire with bare hands can
cause injury. Always wear gloves when
using the piano wire.
Note
• Use a long sawing action to spread the work
over the whole length of the piano wire to
prevent it from breaking.
3. Fix one end of the piano wire, and while pulling
the other end, cut the sealant to remove the base.
End Of Sie
BASE INSTALLATION
id091200803300
1. Cut away all of the original sealant using a razor.
Warning
• Using a razor with bare hands can cause injury. Always wear gloves when using a razor.
2. Clean and degrease the ceramic coating on the glass and the base.
Caution
• Keep the area free of dirt and grease, and do not touch the surface. Otherwise, the primer may not
properly bond to the surface of the glass.
3. Apply primer to the bonding area of the glass and the base.
4. Use only glass primer on the glass, and body primer on the base. Allow the primer to dry for approx. 30 min.
5. Apply 3.0 mm {0.12 in} layer of sealant to the
base.
BASE
REARVIEW MIRROR
acxuuw00001668
PIANO WIRE
acxuuw00001981
NOZZLE
SEALANT
BASE
3.0 mm
{0.12 in}
acxuuw00001982
GLASS/WINDOWS/MIRRORS
09-12–37
09-12
6. Center the base in the ceramic coating and press
it onto the glass.
7. Use isopropyl alcohol to remove any excess
repair sealant.
Hardening time of sealant
8. Install the rearview mirror.
End Of Sie
Temperature
Surface
hardening time
Time required
until car can be
put into service
5
°C {41 °F}
Approx. 1.5 h
Approx. 12 h
20
°C {68 °F}
Approx. 1 h
Approx. 4 h
35
°C {95 °F}
Approx. 10 min
Approx. 2 h
CERAMIC COATING
BASE
5 mm
{0.2 in}
acxuuw00001983
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст