Mazda CX 7. Manual — part 373
SYMPTOM TROUBLESHOOTING [CAR-NAVIGATION SYSTEM]
09-03H–13
09-03H
*
: It is used for symptom troubleshooting. (Troubleshooting index No. 5 and No. 8)
Finishing Procedure For Diagnostic Function
1. Turn the ignition switch to the LOCK position.
2. Turn the ignition switch to the ACC or ON position.
3. Return to the normal screen.
End Of Sie
8
Microphone input level
judging
Indicate the test result.
• Blue indicator: The sound is inputted from the microphone properly.
• Gray indicator: The sound is inputted from the microphone improperly.
9
Microphone level
Indicate the input level of microphone by bar graph.
No.
Display item
Description
1871-1U-06B(09-03H).fm 13 ページ 2006年3月15日 水曜日 午前11時47分
BODY PANELS
09-10–1
09-10
09-10
BODY PANELS
FUEL-FILLER LID
REMOVAL/INSTALLATION . . . . . . . . . 09-10–1
FUEL-FILLER LID
ADJUSTMENT . . . . . . . . . . . . . . . . . . . 09-10–1
FRONT BUMPER
REMOVAL/INSTALLATION. . . . . . . . . . 09-10–2
Front Bumper Removal Note . . . . . . . . 09-10–2
Front Bumper Installation Note . . . . . . 09-10–2
FRONT BUMPER
DISASSEMBLY/ASSEMBLY . . . . . . . . 09-10–3
FRONT BUMPER REINFORCEMENT
REMOVAL/INSTALLATION . . . . . . . . . 09-10–4
REAR BUMPER
REMOVAL/INSTALLATION . . . . . . . . . 09-10–4
Rear Bumper Removal Note . . . . . . . . 09-10–5
Rear Bumper Installation Note . . . . . . . 09-10–5
REAR BUMPER
DISASSEMBLY/ASSEMBLY . . . . . . . . . 09-10–6
Reflector Removal Note . . . . . . . . . . . . 09-10–6
REAR BUMPER REINFORCEMENT
REMOVAL/INSTALLATION . . . . . . . . . . 09-10–6
FRONT FENDER PANEL
REMOVAL/INSTALLATION . . . . . . . . . . 09-10–7
LOCATION INDEX . . . . . . . . . . . . . . . . . . 09-10–8
HOOD REMOVAL/INSTALLATION . . . . . 09-10–9
HOOD ADJUSTMENT . . . . . . . . . . . . . . . 09-10–10
Gap Adjustment . . . . . . . . . . . . . . . . . . 09-10–10
Height Adjustment. . . . . . . . . . . . . . . . . 09-10–11
SHROUD PANEL
REMOVAL/INSTALLATION . . . . . . . . . . 09-10–12
Upper Mount Rubber Bracket . . . . . . . . 09-10–12
COWL PANEL
REMOVAL/INSTALLATION . . . . . . . . . . 09-10–13
End of Toc
WM: FUEL-FILLER LID
FUEL-FILLER LID REMOVAL/INSTALLATION
id091000800100
1. Remove the bolts..
2. Remove the fuel-filler lid
3. Install in the reverse order of removal.
4. Adjust the fuel-filler lid. (See 09-10-1 FUEL-
FILLER LID ADJUSTMENT.)
End Of Sie
FUEL-FILLER LID ADJUSTMENT
id091000800200
1. Measure the gap and height difference between the fuel-filler lid and the body.
2. Loosen the fuel-filler lid installation bolts and
adjust the fuel-filler lid.
Clearance
a: 1.7— 3.7 mm {0.07— 0.14 in}
b: -0.5— 1.5 mm {-0.01— 0.05 in}
3. Tighten the bolts.
End Of Sie
WM: BUMPER
FUEL-FILLER LID
3.9—5.9 N·m
{39.8—60.1 kgf·cm,
34.6—52.2 in·lbf}
BOLT
acxuuw00001304
SEC. A—A
A
A
a
b
acxuuw00001305
BODY PANELS
09-10–2
FRONT BUMPER REMOVAL/INSTALLATION
id091000800300
1. Disconnect the negative battery cable.
2. Remove in the order indicated in the table.
3. Disconnect the front fog light connector. (Vehicles
with front fog lights)
4. Install in the reverse order of removal.
5. Adjust the front fog light aiming for vehicles with
front fog lights. (See 09-18-9 FRONT FOG LIGHT
AIMING.)
Front Bumper Removal Note
1. Pull the front bumper ends (wheel arch) outward
(1) to disengage from the bumper slider.
Caution
• When disengaging the front bumper from
the bumper slider, the front bumper could
fall and be dameged. Secure the front
bumper so that it does not fall.
2. Remove the front bumper from the body.
Front Bumper Installation Note
1. Spread the front bumper ends apart.
2. Assemble the front bumper to the body.
3. Press the front bumper connecting area into the body to engage with the bumper slider.
End Of Sie
1
Screw A
2
Bolt
3
Fastener A
4
Fastener B
5
Fastener C
6
Screw B
7
Front bumper
(See 09-10-2 Front Bumper Removal Note)
(See 09-10-2 Front Bumper Installation Note)
1
7
6
5
3
2
1
6.9—9.8 N·m {70.3—99.9
kgf·cm, 61.1—86.7 in·lbf}
4
6
5
acxuuw00001306
BUMPER SLIDER
FRONT
BUMPER
(1)
(1)
acxuuw00001307
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст