Mazda CX 7. Manual — part 374
BODY PANELS
09-10–3
09-10
FRONT BUMPER DISASSEMBLY/ASSEMBLY
id091000800400
1. Remove the front fog light. (Vehicles with front fog lights) (See 09-18-9 FRONT FOG LIGHT REMOVAL/
INSTALLATION.)
2. Remove the radiator grille. (See 09-16-11 RADIATOR GRILLE REMOVAL/INSTALLATION.)
3. Disassemble in the order indicated in the table.
4. Assemble in the reverse order of disassembly.
End Of Sie
2
9
10
11
7
8
5
6
16
4
12
3
15
14
13
17
18
1
TAB A
TAB B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
FRONT FOG LIGHT
HOLE COVER
FRONT BUMPER
FASCIA
A
A
A
A
A
A
A
A
acxuuw00001308
1
Front fog light hole cover (Vehicles with front fog
lights)
2
Front fog light hole cover (Vehicles without front fog
lights)
3
Screw A
4
Front bumper retainer
5
Screw B
6
Clip nut A
7
Fastener A
8
Screw C
9
Fastener B
10
Front airdam skirt
11
Clip nut B
12
Front bumper mesh
13
Seal plate
14
Fastener C
15
Seal rubber
16
Screw D
17
Air duct
18
Furnt bumper fascia
BODY PANELS
09-10–4
FRONT BUMPER REINFORCEMENT REMOVAL/INSTALLATION
id091000800600
1. Disconnect the negative battery cable.
2. Remove the front bumper. (See 09-10-2 FRONT BUMPER REMOVAL/INSTALLATION.)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
End Of Sie
REAR BUMPER REMOVAL/INSTALLATION
id091000800700
1. Disconnect the negative battery cable.
2. Remove the rear combination light. (See 09-18-11 REAR COMBINATION LIGHT REMOVAL/INSTALLATION.)
3. Remove the screw and fastener.
4. Splash shield, detach tabs A, and then remove
the splash shield.
1
Fastener A
2
Front energy-absorbing foam
3
Fastener B
4
Seal plate
5
Bolt A
6
Bolt B
7
Front bumper reinforcement
A
A
5
5
5
5
7
2
3
4
3
4
56.1—78.5 N·m
{5.72—8.00 kgf·m, 41.4—57.8 ft·lbf}
6
1
7.8—11.8 N·m
{79.5—120.3 kgf·cm, 69.0—104.4 in·lbf}
acxuuw00001309
TAB A
SCREW
SCREW
FASTENER
SPLASH SHIELD
A
A
A
A
acxuuw00001310
BODY PANELS
09-10–5
09-10
5. Remove in the order indicated in the table.
6. Install in the reverse order of removal.
Rear Bumper Removal Note
1. Pull the rear bumper ends (wheel arch) outward
(1) to disengage from the bumper slider.
Caution
• When disengaging the rear bumper from
the bumper slider, the rear bumper could
fall and be damaged. Secure the rear
bumper so that it does not fall.
2. Remove the rear bumper (2).
Rear Bumper Installation Note
1. Spread the rear bumper ends apart.
2. Assemble the rear bumper to the body.
3. Press the rear bumper connecting area into the body to engage with the bumper slider.
End Of Sie
1
Fastener
2
Screw
3
Rear bumper
(See 09-10-5 Rear Bumper Removal Note)
(See 09-10-5 Rear Bumper Installation Note)
1
3
1
A
A
2
1
TAB
REAR BUMPER
acxuuw00001311
(1)
(1)
(2)
BUMPER SLIDER
REAR BUMPER
acxuuw00001312
BODY PANELS
09-10–6
REAR BUMPER DISASSEMBLY/ASSEMBLY
id091000800800
1. Disassemble in the order indicated in the table.
2. Assemble in the reverse order of disassembly.
Reflector Removal Note
1. Remove the screw.
2. Pull off the reflector from the rear bumper in the
direction shown by the arrow.
End Of Sie
REAR BUMPER REINFORCEMENT REMOVAL/INSTALLATION
id091000800900
1. Disconnect the negative battery cable.
2. Remove the rear combination light. (See 09-18-5 FRONT COMBINATION LIGHT REMOVAL/INSTALLATION.)
3. Remove the rear bumper. (See 09-10-4 REAR BUMPER REMOVAL/INSTALLATION.)
4. Remove the fasteners, then remove the energy-
absorbing foam.
5. Remove the nuts, then remove the rear bumper
reinforcement.
6. Install in the reverse order of removal.
End Of Sie
WM: FRONT FENDER PANEL
1
Locator pin
2
Screw A
3
Rear reflector
(See 09-10-6 Reflector Removal Note)
4
Bumper guard
5
Screw B
6
Rear bumper fascia
1
4
5
4
2
6
3
2
PUSH
TAB
acxuuw00001313
PUSH
SCREW
REFLECTOR
TAB
acxuuw00001314
ENERGY-ABSORBING
FOAM
FASTENER
NUT
N·m {kgf·m, ft·lbf}
37.3—52.0
{3.81—5.30,
27.6—38.3}
37.3—52.0
{3.81—5.30,
27.6—38.3}
NUT
REAR BUMPER
REINFORCEMENT
acxuuw00001315
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст