Mazda CX 7. Manual — part 267
AUTOMATIC TRANSAXLE SHIFT MECHANISM
05-18–3
05-18
3. Remove the clip of the selector lever base plate,
then remove the interlock cable from the U-
groove.
4. Remove the interlock cable from the selector
lever.
5. Remove the lock unit from the bracket.
6. Verify that the marking on the slider pin is
positioned as shown in the figure.
7. Push the interlock cable.
CLIP
INTERLOCK
CABLE
acxuuw00000403
BRACKET
LOCK UNIT
acxuuw00000404
MARKING
SLIDER PIN
acxuuw00000405
INTERLOCK CABLE
acxuuw00000406
1871-1U-06B(05-18).fm 3 ページ 2006年3月15日 水曜日 午前11時23分
AUTOMATIC TRANSAXLE SHIFT MECHANISM
05-18–4
8. Insert the a 1.5mm {0.059 in} round bar or similar
into hole A with the slider pin fully pushed in.
9. Fully pull the end of the interlock cable.
10. Push the a 1.5mm {0.059 in} round bar or similar
into hole B and hole C of the lock unit until it
passes through.
11. Disconnect the brake switch connector.
12. Remove the brake switch. (See04-11-6 BRAKE
PEDAL REMOVAL/INSTALLATION.)
13. Install a new brake switch. (See04-11-6 BRAKE
PEDAL REMOVAL/INSTALLATION.)
Caution
• Do not connect the brake switch
connector until the interlock cable
adjustment is completed.
14. Install the lock unit to the bracket. (See05-18-10 Interlock Cable Installation Note.)
15. Rotate the slider pin to release the lock and verify that it slides freely.
16. Verify that the slider pin contacts the brake pedal
stopper rubber and rotate the slider pin to lock.
SLIDER PIN
INTERLOCK
CABLE
BRAKE SWITCH
A
B
C
LOCK UNIT
acxuuw00000407
INTERLOCK CABLE
acxuuw00000408
SLIDER PIN
INTERLOCK
CABLE
BRAKE SWITCH
A
B
C
LOCK UNIT
acxuuw00000407
MARKING
SLIDER PIN
UNLOCK
LOCK
acxuuw00000409
1871-1U-06B(05-18).fm 4 ページ 2006年3月15日 水曜日 午前11時23分
AUTOMATIC TRANSAXLE SHIFT MECHANISM
05-18–5
05-18
17. Install the interlock cable end to the interlock link
on the selector lever.
18. Fit the interlock cable in the U-groove in the
selector lever base plate and install the clip.
19. Press the interlock cable lock piece in until it is
locked.
Caution
• Applying a load to the interlock cable
while pressing the lock piece in can
affect the lock unit operation.
20. Remove the a 1.5mm {0.059 in} round bar or
similar from the lock unit holes A, B, and C.
21. Connect the brake switch connector with the
brake pedal released.
Caution
• The clearance between the brake switch
and the brake pedal is automatically
adjusted to the correct amount when the
brake switch connector is connected
after the brake switch has been properly
installed. If the brake switch is not
properly installed or the connector is
connected before installation, the
clearance may be incorrect, causing a brake light malfunction. Therefore, always verify that the
brake switch is properly installed before connecting the connector.
• Once the brake switch clearance has automatically been adjusted, it cannot be adjusted again.
Therefore, replace the switch with a new one when replacing the power brake unit or the pedal, or
performing any procedure that changes the pedal stroke.
22. Inspect shift lock operation. (See05-18-2 SHIFT-LOCK INSPECTION.)
End Of Sie
WM: SELECTOR LEVER COMPONENT
CLIP
INTERLOCK
CABLE
acxuuw00000403
LOCK PIECE
INTERLOCK CABLE
UNLOCK
LOCK
acxuuw00000410
SLIDER PIN
INTERLOCK
CABLE
BRAKE SWITCH
A
B
C
LOCK UNIT
acxuuw00000407
1871-1U-06B(05-18).fm 5 ページ 2006年3月15日 水曜日 午前11時23分
AUTOMATIC TRANSAXLE SHIFT MECHANISM
05-18–6
SELECTOR LEVER INSPECTION
id051800800500
1. Turn the ignition switch to the ON position. (engine OFF)
2. With the brake pedal depressed, verify that there
is a “click” at each range when shifted.
3. Verify that the selector lever can be shifted.
4. Verify that there is a “click” at each position when
shifted from P position to M range.
5. Verify that the positions of the selector lever and
the indicator are aligned.
• If there is any malfunction, adjust the TR
switch. (See05-17-25 TCM REMOVAL/
INSTALLATION[AW6A-EL, AW6AX-EL].)
6. Verify that the vehicle operates in each selected
range.
End Of Sie
SELECTOR LEVER COMPONENT INSPECTION
id051800800600
1. Disconnect the negative battery cable.
2. Remove the center console.
3. Remove the dashboard completely. (See 09-17-4 DASHBOARD REMOVAL/INSTALLATION.)
4. Disconnect the selector lever component connector.
5. Inspect for continuity at the selector lever
component.
• If there is any malfunction, adjust the selector
cable. (See 05-18-7 SELECTOR CABLE
ADJUSTMENT.)
End Of Sie
OPERATION WHEN
BRAKE PEDAL IS
DEPRESSED
OPERATION WHEN
BRAKE PEDAL IS
RELEASED
acxuuw00000411
SELECTOR INDICATOR LIGHT
acxuuw00000412
E
C
A
F
D
B
acxuuw00002533
Selector lever
position/range
Connector terminal
: Continuity
A
B
C
D
E
F
M range
Other
center M
- M
+ M
D6U518ZW7002
1871-1U-06B(05-18).fm 6 ページ 2006年3月15日 水曜日 午前11時23分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст