Mazda CX 7. Manual — part 268
AUTOMATIC TRANSAXLE SHIFT MECHANISM
05-18–7
05-18
SELECTOR CABLE ADJUSTMENT
id051800800700
1. Remove the center console.
2. Shift the selector lever to P position.
3. Unlock the lock piece of the selector cable
(selector lever side) in the order shown in the
figure.
4. Verify that the manual shaft is in P position.
5. Lock the lock piece of the selector cable (selector
lever side) in the order shown in the figure.
6. Install the center console.
7. Shift the selector lever from P position to M range,
and make sure that there are no other
components in that area to interfere with the lever.
End Of Sie
SELECTOR LEVER COMPONENT REMOVAL/INSTALLATION
id051800800800
1. Disconnect the negative battery cable.
2. Remove the following parts.
(1) Battery and battery tray
(2) Air cleaner component (See 01-13-5 INTAKE AIR SYSTEM REMOVAL/INSTALLATION[L3 WITH TC].)
(3) Selector lever knob
(4) Center console
(5) Driver side under panel
(6) Accelerator pedal (See 01-13-17 ACCELERATOR PEDAL REMOVAL/INSTALLATION[L3 WITH TC].)
3. Remove in the order shown in the figure.
1
2
acxuuw00000413
1
2
acxuuw00000414
1871-1U-06B(05-18).fm 7 ページ 2006年3月15日 水曜日 午前11時23分
AUTOMATIC TRANSAXLE SHIFT MECHANISM
05-18–8
4. Install in the reverse order of removal.
.
A
A
9
8
7
5
4
3
6
1
2
SELECTOR LEVER KNOB
6.9—9.8 N·m
{71—99 kgf·cm, 62—86 in·lbf}
16—22 {1.7—2.2, 12—16}
N·m {kgf·m, ft·lbf}
acxuuw00000415
1
Column cover
2
Clip
3
Indicator panel
4
Clip
5
Interlock cable
(See05-18-10 Interlock Cable Installation Note.)
6
Clip
7
Clip
8
Selector cable
(See05-18-9 Selector Cable Removal Note.)
(See05-18-9 Selector Cable Installation Note.)
9
Selector lever component
1871-1U-06B(05-18).fm 8 ページ 2006年3月15日 水曜日 午前11時23分
AUTOMATIC TRANSAXLE SHIFT MECHANISM
05-18–9
05-18
Selector Cable Removal Note
1. Remove the clip.
2. Remove the selector cable.
3. Remove the selector cable from the cable
bracket.
Selector Cable Installation Note
1. Install the selector cable and clip to the bracket as
shown in the figure.
Note
• Steps 2 and 3 are for the selector cable
replacement only.
2. Verify that the selector lever is in the P position.
3. Lock the lock piece of the selector cable (selector
lever side) in the order shown in the figure.
TCM
CLIP
MANUAL
SHAFT
LEVER
SELECTOR
CABLE
acxuuw00000416
CLIP
SELECTOR
CABLE
CABLE
BRACKET
acxuuw00002399
CLIP
SELECTOR
CABLE
CABLE
BRACKET
acxuuw00002400
1
2
acxuuw00000419
1871-1U-06B(05-18).fm 9 ページ 2006年3月15日 水曜日 午前11時23分
AUTOMATIC TRANSAXLE SHIFT MECHANISM
05-18–10
4. Verify that the manual shaft is in the P position.
Caution
• Bending the selector cable in the manner
shown in the figure will damage the cable
and it may become loose when shifted.
When installing the selector cable, hold it
straight.
5. Install the clip as shown in the figure.
Note
• Install the selector lever to the manual shaft
lever with the clip side of the selector cable
end facing up.
6. Install the selector lever to the manual shaft lever
so that no load acts on the selector cable.
7. Confirm that the tip of the manual shaft lever
projects out of the end of the selector cable.
8. Securely install the selector cable to the selector
cable bracket.
Interlock Cable Installation Note
1. Push the interlock cable.
2. Verify that the marking on the slider pin is
positioned as shown in the figure.
DO NOT BEND
acxuuw00000432
CLIP
acxuuw00000433
SELECTOR CABLE
MANUAL SHAFT LEVER
CLIP
UPWARD
acxuuw00000422
INTERLOCK CABLE
acxuuw00000423
BRACKET
LOCK UNIT
acxuuw00000424
1871-1U-06B(05-18).fm 10 ページ 2006年3月15日 水曜日 午前11時23分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст