Mazda CX 7. Manual — part 339
ON-BOARD DIAGNOSTIC [MULTIPLEX COMMUNICATION SYSTEM]
09-02D–13
09-02D
Climate Control Unit
Note
• There is no DTC in the climate control unit that determines signal quality between it and the information
display. Due to this, determine the malfunction location using the DTC on the information display.
1. Inspect the display of DTC U0155 using the M-MDS. (See 09-02D-7 DTC TABLE[MULTIPLEX
COMMUNICATION SYSTEM].)
2. Referring to the following table, determine the malfunctioning part of the CAN system.
×: Normal
— : Communication error
Car- navigation Unit/Audio Unit (Base Module)
Note
• There is no DTC in the car-navigation unit/audio unit (base module) that determines signal quality
between it and the information display. Due to this, determine the malfunction location using the DTC on
the information display.
1. Referring to the following table, determine the malfunctioning part of the CAN system.
×: Normal
— : Communication error
Information display
1. Inspect the display of DTC U0166, U0181 and/or U0184 using the input/output check mode. (See 09-22-15
INFORMATION DISPLAY INPUT/OUTPUT CHECK MODE.)
2. Referring to the following table, determine the malfunctioning part of the CAN system.
×: Normal
— : Communication error
Module
Communication status
Malfunction location
Instrument cluster
Information display
Climate control
unit
— —
• Wiring harness O
• Climate control unit
—
×
• Wiring harness N
• Instrument cluster
×
—
• Wiring harness Q
• Wiring harness S
• Information display
Module
Communication status
Malfunction location
Information display
Car-navigation unit
Audio unit (base module)
—
• Wiring harness P
• Wiring harness Q
• Wiring harness S
• Car-navigation unit
• Audio unit (base module)
• Information display
Module
Communication status
Malfunction location
Climate control unit
Car-navigation unit
Audio unit (base module)
Instrument cluster
Information
display
— — —
• Wiring harness Q
• Wiring harness S
• Information display
—
×
×
• Wiring harness O
• Climate control unit
×
—
×
• Wiring harness P
• Car-navigation unit
• Audio unit (base
module)
×
×
—
• Wiring harness N
• Instrument cluster
1871-1U-06B(09-02D).fm 13 ページ 2006年3月15日 水曜日 午前11時40分
ON-BOARD DIAGNOSTIC [MULTIPLEX COMMUNICATION SYSTEM]
09-02D–14
Repair Procedure
1. Inspect the connector of malfunctioning module.
• If there is any malfunction, repair or replace the connector.
2. Inspect the malfunctioning wiring harnesses as follow:
• If there is any malfunction, repair or replace the wiring harnesses.
• If there is no malfunction, replace the malfunctioning module.
— Short to GND
— Short to power supply
— Twisted pair short each other
— Open circuit
3. Make sure to reconnect all disconnected connectors.
4. Clear the CAN system related DTCs using the M-MDS.
5. Verify if the CAN system related DTCs are displayed using the M-MDS.
• If the same following DTCs are present, replace the malfunctioning module.
— U0073 (PCM, TCM, DSC HU/CM, AWD control module, BCM, SAS control module, keyless control
module, instrument cluster)
— U0516 (Climate control unit)
— U2516 (Instrument cluster, information display)
— 16:Er12 (Audio unit (base module))
• If other DTC is present, perform the appropriate DTC inspection. (See 09-02D-7 DTC TABLE[MULTIPLEX
COMMUNICATION SYSTEM].)
End Of Sie
DTC U0073[MULTIPLEX COMMUNICATION SYSTEM]
id0902e6824800
DTC
U0073
PCM
TCM
DSC HU/CM
AWD control module
BCM
SAS control module
Keyless control module
Instrument cluster
CAN system communication error
DETECTION
CONDITION
Warning
• Detection conditions are for understanding the DTC outline before performing an inspection.
Performing an inspection according to only detection conditions may cause injury due to
operating error, or damage the system. When performing an inspection, always follow the
inspection procedure.
• CAN system related harness malfunction
• Related module communication error
POSSIBLE
CAUSE
• Open or short circuit in wiring harness
• Malfunction of connectors between PCM, TCM, DSC HU/CM, AWD control module, BCM, SAS control
module, keyless control module, instrument cluster
• PCM malfunction
• TCM malfunction
• DSC HU/CM malfunction
• AWD control module malfunction
• BCM malfunction
• SAS control module malfunction
• Keyless control module malfunction
• Instrument cluster malfunction
1871-1U-06B(09-02D).fm 14 ページ 2006年3月15日 水曜日 午前11時40分
ON-BOARD DIAGNOSTIC [MULTIPLEX COMMUNICATION SYSTEM]
09-02D–15
09-02D
Diagnostic procedure
End Of Sie
STEP
INSPECTION
ACTION
1
INSPECT CAN SYSTEM-RELATED DTC
• Are any DTCs other than the following
displayed?
— U0073
Yes
Determine malfunctioning part in CAN system.
(See 09-02D-8 PROCEDURES FOR DETERMINING THE
LOCATION OF A MALFUNCTION[MULTIPLEX
COMMUNICATION SYSTEM])
No
Go to the next step.
2
INSPECT CONNECTOR
• Inspect the connector of the module that
outputs the DTC.
• Is it normal?
Yes
Go to the next step.
No
Repair or replace the connector, then go to Step 4.
3
INSPECT WIRING HARNESSES
• Inspect for the following malfunctioning
wiring harnesses:
— Short to GND
— Short to power supply
— Twisted pair short each other
— Open circuit
• Is there any malfunction?
Yes
Repair or replace the wiring harness, then go to the next
step.
No
Go to the next step.
4
VERIFY TROUBLESHOOTING COMPLETED
• Make sure to reconnect all disconnected
connectors.
• Clear the DTC using the M-MDS.
• Is the same DTC present?
Yes
Replace the module that outputs the DTC, then retry this
step.
No
Troubleshooting completed.
DTC
U0073
PCM
TCM
DSC HU/CM
AWD control module
BCM
SAS control module
Keyless control module
Instrument cluster
CAN system communication error
F
E
2R
2T
3X
3W
5L
5I
DLC-2
1AI
1AM
3X
3W
G
H
PCM
TCM
BCM
BCM
X
W
DSC HU/CM
KEYLESS
CONTROL
MODULE
2E
2F
SAS
CONTROL
MODULE
AWD
CNTROL
MODULE
A14
A6
INSTRUMENT
CLUSTER
FRONT HARNESS
EMISSION HARNESS
INSTRUMENT PANEL
HARNESS
:
:
CAN_H
CAN_L
REAR HARNESS
1871-1U-06B(09-02D).fm 15 ページ 2006年3月15日 水曜日 午前11時40分
ON-BOARD DIAGNOSTIC [MULTIPLEX COMMUNICATION SYSTEM]
09-02D–16
DTC U0516, U2516, 16:Er12[MULTIPLEX COMMUNICATION SYSTEM]
id0902e6837100
Diagnostic procedure
End Of Sie
DTC
U0516
Climate control unit
CAN system communication error
U2516
Information display
Instrument cluster
16:Er12
Audio unit (base
module)
DETECTION
CONDITION
Warning
• Detection conditions are for understanding the DTC outline before performing an inspection.
Performing an inspection according to only detection conditions may cause injury due to
operating error, or damage the system. When performing an inspection, always follow the
inspection procedure.
• CAN system related harness malfunction
• Related module communication error
POSSIBLE
CAUSE
• Open or short circuit in wiring harness
• Malfunction of connectors between information display, audio unit (base module), climate control unit
and instrument cluster
• Climate control unit malfunction
• Information display malfunction
• Audio unit (base module) malfunction
• Instrument cluster malfunction
STEP
INSPECTION
ACTION
1
INSPECT CAN SYSTEM-RELATED DTC
• Are any DTCs other than the following
displayed?
— U0516
— U2516
— 16:Er12
Yes
Determine malfunctioning part in CAN system.
(See 09-02D-8 PROCEDURES FOR DETERMINING THE
LOCATION OF A MALFUNCTION[MULTIPLEX
COMMUNICATION SYSTEM].)
No
Go to the next step.
2
INSPECT CONNECTOR
• Inspect the connector of the module that
outputs the DTC.
• Is it normal?
Yes
Go to the next step.
No
Repair or replace the connector, then go to Step 4.
3
INSPECT WIRING HARNESSES
• Inspect for the following malfunctioning
wiring harnesses:
— Short to GND
— Short to power supply
— Twisted pair short each other
— Open circuit
• Is there any malfunction?
Yes
Repair or replace the wiring harness, then go to the next
step.
No
Go to the next step.
4
VERIFY TROUBLESHOOTING COMPLETED
• Make sure to reconnect all disconnected
connectors.
• Clear the DTC using the M-MDS.
• Is the same DTC present?
Yes
Replace the module that outputs the DTC, then retry this
step.
No
Troubleshooting completed.
:
:
2X
2V
B
A
L
K
2O
2P
1O
1Q
CAN_H
CAN_L
DLC-2
J
I
INSTRUMENT
CLUSTER
CLIMATE
CONTROL UNIT
AUDIO
AMPLIFIER
INFORMATION
DISPLAY
AUDIO UNIT
(BASE MODULE)
INSTRUMENT PANEL
HARNESS
REAR HARNESS
1871-1U-06B(09-02D).fm 16 ページ 2006年3月15日 水曜日 午前11時40分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст