Mazda CX 7. Manual — part 193
ALL WHEEL DRIVE (AWD)
03-19–3
03-19
End Of Sie
AWD CONTROL MODULE REMOVAL/INSTALLATION
id031900800300
1. Disconnect the negative battery cable.
2. Remove the lower panel (Driver’s side). (See 09-17-9 LOWER PANEL REMOVAL/INSTALLATION.)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
.
AWD CM Removal Note
1. Push up the AWD CM slightly, and remove it.
End Of Sie
WM: COUPLING COMPONENT
P
AWD solenoid
(-)
Output AWD solenoid
Voltage
Ignition key ON
B+
• AWD solenoid
• Inspect related
harness
Ignition key OFF
1.0 or below
Terminal
Signal
Input/
output
Connected
to
Measuring
item
Test condition
Voltage (V)/
Continuity
Inspection location
in case of failure
N·m { kgf· cm, in·lbf}
3
1
2
8.8—12.7
{90—129 , 78—112}
acxuuw00001972
1
Bolt
2
AWD CM
(See 03-19-3 AWD CM Removal Note.)
3
Connector
AWD CM
acxuuw00001973
1871-1U-06B(03-19).fm 3 ページ 2006年3月15日 水曜日 午前11時9分
ALL WHEEL DRIVE (AWD)
03-19–4
COUPLING COMPONENT REMOVAL/INSTALLATION
id031900800400
1. Drain the rear differential oil into a container.
2. Remove the main silencer and middle pipe. (See 01-15-2 EXHAUST SYSTEM REMOVAL/INSTALLATION[L3
WITH TC].)
3. Remove the propeller shaft. (See 03-15-3 PROPELLER SHAFT REMOVAL/INSTALLATION.)
4. Remove in the order indicated in the table.
5. Install in the reverse order of removal.
6. Add rear differential oil. (See 03-14-2 DIFFERENTIAL OIL REPLACEMENT.)
.
Coupling Component Removal Note
1. Support the coupling unit with a transmission jack.
2. Cut away the coupling unit using an oil pan seal
cutter.
SEALANT
1
2
3
N·m {kgf·m, ft·lbf}
75.5—102
{7.70—10.4,
55.7—75.2}
75.5—102
{7.70—10.4,
55.7—75.2}
22.6—26.4
{2.31—2.69,
16.7—19.4}
acxuuw00001974
1
AWD solenoid connector
2
Bolt
3
Coupling component
(See 03-19-4 Coupling Component Removal Note)
(See 03-19-5 Coupling Component Installation
Note)
OIL PAN
SEAL CUTTER
acxuuw00001441
1871-1U-06B(03-19).fm 4 ページ 2006年3月15日 水曜日 午前11時9分
ALL WHEEL DRIVE (AWD)
03-19–5
03-19
Coupling Component Installation Note
Note
• Clean away the old sealant before applying the new sealant.
• Install the coupling unit within 10 min after applying sealant.
• Allow the sealant to set at least 30 min after installation before filling the differential with the specified oil.
1. Apply sealant to the coupling case surface that contacts the rear differential case.
2. Install the coupling unit to the rear differential so
that the two tabs on the coupling unit engage the
rear differential grooves (two locations).
Tightening torque
22.6— 26.4 N·m {2.4— 2.6 kgf·m, 16.7— 19.4
ft·lbf}
End Of Sie
COUPLING COMPONENT DISASSEMBLY
id031900800500
Warning
• The engine stand is equipped with a self-lock mechanism, however, if the coupling unit is in a
tilted condition, the self-lock mechanism could become inoperative. If the coupling unit
unexpectedly rotates it could cause injury, therefore do not maintain the coupling unit in a tilted
condition. When turning the coupling unit, grasp the rotation handle firmly.
.
GROOVE
REAR DIFFERENTIAL
COUPLING UNIT
TAB
acxuuw00001442
SST
SST
SST
SST
9
8
7
5
4
3
1
2
10
6
acxuuw00001443
1
Locknut
(See 03-19-6 Locknut Disassembly Note)
2
Washer
3
Companion flange
(See 03-19-6 Companion Flange Disassembly
Note)
1871-1U-06B(03-19).fm 5 ページ 2006年3月15日 水曜日 午前11時9分
ALL WHEEL DRIVE (AWD)
03-19–6
Locknut Disassembly Note
1. Assemble the SSTs to the engine stand.
2. Install the coupling unit to the SSTs as shown.
3. Secure the companion flange using the SST, and
remove the locknut.
Companion Flange Disassembly Note
1. Remove the companion flange using the SST.
4
Output shaft
(See 03-19-7 Output Shaft Disassembly Note)
5
Coupling component
6
Oil seal
7
Shim
8
Snap ring
9
Bearing
(See 03-19-7 Bearing Disassembly Note)
10
Coupling case
49 L027 0A2
49 0107 680A
acxuuw00001444
49 L027 0A2
acxuuw00002359
49 S120 710
acxuuw00001446
49 0839 425C
acxuuw00002356
1871-1U-06B(03-19).fm 6 ページ 2006年3月15日 水曜日 午前11時9分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст