Mazda CX 7. Manual — part 312
ON-BOARD DIAGNOSTIC
08-02–43
08-02
DTC B2445, U2018
id080200802800
Diagnostic procedure
DTC
B2445
Passenger-side side air bag sensor No.1 (internal circuit abnormal)
U2018
Passenger-side side air bag sensor No.1 (communication error)
DETECTION
CONDITION
Warning
• Detection conditions are for understanding the DTC outline before performing an inspection.
Performing an inspection according to only the detection conditions may cause injury due to
an operating error, or damage the system. When performing an inspection, always follow the
inspection procedure.
• Malfunction in the wiring harness between the passenger-side side air bag sensor and SAS control
module
• Malfunction in the passenger-side side air bag sensor circuit
POSSIBLE
CAUSE
• Open or short circuit in the wiring harness between the passenger-side side air bag sensor and SAS
control module
• Passenger-side side air bag sensor malfunction
• SAS control module malfunction
STEP
INSPECTION
ACTION
1
INSPECT PASSENGER-SIDE SIDE AIR BAG
SENSOR NO. 1 CONNECTOR
Warning
• Handling the air bag system
components improperly can
accidentally deploy the air bag
modules and pre-tensioner seat belts,
which may seriously injure you. Read
the service warnings and cautions
before handling the air bag system
components.
(See 08-10-3 AIR BAG SYSTEM
SERVICE WARNINGS.)
(See 08-10-5 AIR BAG SYSTEM
SERVICE CAUTIONS.)
• Turn the ignition switch to the LOCK position.
• Disconnect the negative battery cable and
wait for 1 min or more.
• Remove the B-pillar lower trim (passenger-
side).
(See 09-17-16 B-PILLAR LOWER TRIM
REMOVAL/INSTALLATION.)
• Disconnect the passenger-side side air bag
sensor No. 1 connector.
• Is there any malfunction of the passenger-
side side air bag sensor No. 1 connector?
Yes
Replace the air bag wiring harness.
No
Go to the next step.
A
B
SAS CONTROL MODULE WIRING
HARNESS-SIDE CONNECTOR
PASSENGER-SIDE SIDE AIR BAG SENSOR NO.1
WIRING HARNESS-SIDE CONNECTOR
2A
2B
2C
2D
2E
2F
2G
2H
2I
2J
2L
2M
2O
2P
2R
2S
2T
2U
2V
2W
2Y
2X
2Z
2AA
1871-1U-06B(08-02).fm 43 ページ 2006年3月15日 水曜日 午前11時33分
ON-BOARD DIAGNOSTIC
08-02–44
End Of Sie
2
INSPECT WIRING HARNESS BETWEEN
PASSENGER-SIDE SIDE AIR BAG SENSOR
NO.1 AND SAS CONTROL MODULE
• Turn the ignition switch to the LOCK position.
• Disconnect the negative battery cable and
wait for 1 min or more.
• Remove the column cover. (See 09-17-8
COLUMN COVER REMOVAL/
INSTALLATION.)
• Disconnect the clock spring connector.
• Remove the glove compartment. (See 09-17-
8 GLOVE COMPARTMENT REMOVAL/
INSTALLATION.)
• Disconnect the passenger-side air bag
module connector.
• Disconnect the driver and passenger-side
seat connectors.
• Remove the C-pillar trim. (See 09-17-17 C-
PILLAR TRIM REMOVAL/INSTALLATION.)
• Remove the D-pillar trim. (See 09-17-18 D-
PILLAR TRIM REMOVAL/INSTALLATION.)
• Disconnect the driver and passenger-side
curtain air bag module connector.
• Remove the B-pillar lower trim. (See 09-17-
16 B-PILLAR LOWER TRIM REMOVAL/
INSTALLATION.)
• Disconnect the driver and passenger-side
pre-tensioner seat belt connectors.
• Disconnect the passenger-side side air bag
sensor No.1 connector.
• Remove the console. (See 09-17-13
CONSOLE REMOVAL/INSTALLATION.)
• Disconnect the SAS control module
connector.
• Connect the negative battery cable.
• Inspect the wiring harnesses between SAS
control module connector terminal 2C and
passenger-side side air bag sensor No.1
connector terminal A, SAS control module
connector terminal 2B and passenger-side
side air bag sensor No.1 connector terminal
B for the following:
— Short to ground
— Short to power supply
— Open circuit
• Is the wiring harness normal?
Yes
Go to the next step.
No
Replace the air bag wiring harness.
3
INSPECT SAS CONTROL MODULE
• Turn the ignition switch to the LOCK position.
• Disconnect the negative battery cable and
wait for 1 min or more.
• Connect the SAS control module connector.
• Connect the passenger-side side air bag
sensor No.1 connector.
• Turn the ignition switch to the ON position.
• Are DTCs B2445 and/or U2018 indicated?
Yes
Replace the SAS control module.
(See 08-10-10 SAS CONTROL MODULE REMOVAL/
INSTALLATION.)
No
DTC troubleshooting completed.
STEP
INSPECTION
ACTION
1871-1U-06B(08-02).fm 44 ページ 2006年3月15日 水曜日 午前11時33分
ON-BOARD DIAGNOSTIC
08-02–45
08-02
DTC B2477
id080200810500
Diagnostic procedure
End Of Sie
DTC B2773, B2774, B2775, B2776
id080200802900
DTC B2477
Configuration error
DETECTION
CONDITION
Warning
• Detection conditions are for understanding the DTC outline before performing an inspection.
Performing an inspection according to only the detection conditions may cause injury due to
an operating error, or damage the system. When performing an inspection, always follow the
inspection procedure.
• SAS control module configuration has not been performed correctly.
POSSIBLE
CAUSE
• SAS control module configuration error
• SAS control module malfunction
STEP
INSPECTION
ACTION
1
INSPECT SAS CONTROL MODULE
• Using the M-MDS, perform SAS control
moduleconfiguration.
• Is DTC B2477 indicated?
Yes
Replace the SAS control module.
(See 08-10-10 SAS CONTROL MODULE REMOVAL/
INSTALLATION.)
No
DTC troubleshooting completed.
DTC
B2773
Driver-side curtain air bag module circuit resistance low
B2774
Driver-side curtain air bag module circuit resistance high
B2775
Driver-side curtain air bag module circuit short to body ground
B2776
Driver-side curtain air bag module circuit short to power supply
DETECTION
CONDITION
Warning
• Detection conditions are for understanding the DTC outline before performing an inspection.
Performing an inspection according to only the detection conditions may cause injury due to
an operating error, or damage the system. When performing an inspection, always follow the
inspection procedure.
• Abnormal resistance (other than 1.4— 3.9 ohms) detected in the driver-side curtain air bag module
circuit
• Malfunction in the wiring harness between the driver-side curtain air bag module and SAS control
module
POSSIBLE
CAUSE
• Open or short circuit in the wiring harness between the driver-side curtain air bag module and SAS
control module
• Driver-side curtain air bag module malfunction
• SAS control module malfunction
A
B
DRIVER-SIDE CURTAIN AIR BAG MODULE
WIRING
HARNESS-SIDE
CONNECTOR
1871-1U-06B(08-02).fm 45 ページ 2006年3月15日 水曜日 午前11時33分
ON-BOARD DIAGNOSTIC
08-02–46
Diagnostic procedure
End Of Sie
STEP
INSPECTION
ACTION
1
INSPECT DRIVER-SIDE CURTAIN AIR BAG
MODULE
• Using the M-MDS, verify the following PID/
DATA monitor.
(See 08-02-8 PID/DATA MONITOR TABLE.)
— RES_CAB_D
• Is the resistance of the driver-side curtain air
bag module normal?
— Resistance: 1.4— 3.9 ohms
Yes
Replace the SAS control module.
(See 08-10-10 SAS CONTROL MODULE REMOVAL/
INSTALLATION.)
No
Go to the next step.
2
INSPECT DRIVER-SIDE CURTAIN AIR BAG
MODULE CONNECTOR
Warning
• Handling the air bag system
components improperly can
accidentally deploy the air bag
modules and pre-tensioner seat belts,
which may seriously injure you. Read
the service warnings and cautions
before handling the air bag system
components.
(See 08-10-3 AIR BAG SYSTEM
SERVICE WARNINGS.)
(See 08-10-5 AIR BAG SYSTEM
SERVICE CAUTIONS.)
• Turn the ignition switch to the LOCK position.
• Disconnect the negative battery cable and
wait for 1 min or more.
• Remove the C-pillar trim. (See 09-17-17 C-
PILLAR TRIM REMOVAL/INSTALLATION.)
• Remove the D-pillar trim. (See 09-17-18 D-
PILLAR TRIM REMOVAL/INSTALLATION.)
• Disconnect the driver-side curtain air bag
module connector.
• Is there any malfunction of the driver-side
curtain air bag module connector?
Yes
Replace the air bag wiring harness.
No
Go to the next step.
3
VERIFY WHETHER MALFUNCTION IS IN
DRIVER-SIDE CURTAIN AIR BAG MODULE
OR RELATED WIRING HARNESS
• Connect the leads of the SST (Fuel and
thermometer checker) or apply 2-ohm
resistance to driver-side curtain air bag
module connector terminals A and B.
• Set the resistance of the SST (Fuel and
thermometer checker) to the 2-ohm
position.
• Connect the negative battery cable.
• Turn the ignition switch to the ON position.
• Are DTCs B2773, B2774, B2775 and/or
B2776 indicated?
Yes
Replace the air bag wiring harness, then go to the next
step.
No
Replace the driver-side curtain air bag module.
(See 08-10-8 CURTAIN AIR BAG MODULE REMOVAL/
INSTALLATION.)
4
INSPECT SAS CONTROL MODULE
• Turn the ignition switch to the LOCK position.
• Disconnect the negative battery cable and
wait for 1 min or more.
• Connect the driver-side curtain air bag
module connector.
• Turn the ignition switch to the ON position.
• Are DTCs B2773, B2774, B2775 and/or
B2776 indicated?
Yes
Replace the SAS control module.
(See 08-10-10 SAS CONTROL MODULE REMOVAL/
INSTALLATION.)
No
DTC troubleshooting completed.
1871-1U-06B(08-02).fm 46 ページ 2006年3月15日 水曜日 午前11時33分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст