Mazda CX 7. Manual — part 311
ON-BOARD DIAGNOSTIC
08-02–39
08-02
Diagnostic procedure
STEP
INSPECTION
ACTION
1
INSPECT CRASH ZONE SENSOR
Warning
• Handling the air bag system
components improperly can
accidentally deploy the air bag
modules and pre-tensioner seat belts,
which may seriously injure you. Read
the service warnings and cautions
before handling the air bag system
components.
(See 08-10-3 AIR BAG SYSTEM
SERVICE WARNINGS.)
(See 08-10-5 AIR BAG SYSTEM
SERVICE CAUTIONS.)
• Turn the ignition switch to the LOCK position.
• Disconnect the negative battery cable and
wait for 1 min or more.
• Disconnect the crash zone sensor connector.
• Is there any malfunction of the crash zone
sensor connector?
Yes
Replace the air bag wiring harness.
No
Go to the next step.
2
INSPECT WIRING HARNESS BETWEEN
CRASH ZONE SENSOR AND SAS CONTROL
MODULE
• Turn the ignition switch to the LOCK position.
• Disconnect the negative battery cable and
wait for 1 min or more.
• Remove the column cover. (See 09-17-8
COLUMN COVER REMOVAL/
INSTALLATION.)
• Disconnect the clock spring connector.
• Remove the glove compartment.(See 09-17-
8 GLOVE COMPARTMENT REMOVAL/
INSTALLATION.)
• Disconnect the passenger-side air bag
module connector.
• Disconnect the driver and passenger-side
seat connectors.
• Remove the C-pillar trim. (See 09-17-17 C-
PILLAR TRIM REMOVAL/INSTALLATION.)
• Remove the D-pillar trim. (See 09-17-18 D-
PILLAR TRIM REMOVAL/INSTALLATION.)
• Disconnect the driver and passenger-side
curtain air bag module connector.
• Remove the B-pillar lower trim. (See 09-17-
16 B-PILLAR LOWER TRIM REMOVAL/
INSTALLATION.)
• Disconnect the driver and passenger-side
pre-tensioner seat belt connectors.
• Remove the console. (See 09-17-13
CONSOLE REMOVAL/INSTALLATION.)
• Disconnect the SAS control module
connector.
• Disconnect the crash zone sensor connector.
• Connect the negative battery cable.
• Inspect the wiring harnesses between SAS
control module terminal 1C and crash zone
sensor terminal A, SAS control module
terminal 1B and crash zone sensor terminal
B for the following:
— Short to ground
— Short to power supply
— Open circuit
• Is the wiring harness normal?
Yes
Replace the crash zone sensor, then go to the next step.
(See 08-10-10 CRASH ZONE SENSOR REMOVAL/
INSTALLATION.)
No
Replace the air bag wiring harness.
1871-1U-06B(08-02).fm 39 ページ 2006年3月15日 水曜日 午前11時33分
ON-BOARD DIAGNOSTIC
08-02–40
End Of Sie
DTC B2444, U2017
id080200802700
3
INSPECT SAS CONTROL MODULE
• Turn the ignition switch to the LOCK position.
• Disconnect the negative battery cable and
wait for 1 min or more.
• Connect the SAS control module connector.
• Connect the crash zone sensor connector.
• Turn the ignition switch to the ON position.
• Is DTC B2296 indicated?
Yes
Replace the SAS control module.
(See 08-10-10 SAS CONTROL MODULE REMOVAL/
INSTALLATION.)
No
DTC troubleshooting completed.
STEP
INSPECTION
ACTION
DTC
B2444
Driver-side side air bag sensor No.1 (internal circuit abnormal)
U2017
Driver-side side air bag sensor No.1 (communication error)
DETECTION
CONDITION
Warning
• Detection conditions are for understanding the DTC outline before performing an inspection.
Performing an inspection according to only the detection conditions may cause injury due to
an operating error, or damage the system. When performing an inspection, always follow the
inspection procedure.
• Malfunction in the wiring harness between the driver-side side air bag sensor No.1 and SAS control
module
• Malfunction in the driver-side side air bag sensor circuit
POSSIBLE
CAUSE
• Open or short circuit in the wiring harness between the driver-side side air bag sensor No.1 and SAS
control module
• Driver-side side air bag sensor malfunction
• SAS control module malfunction
A
B
SAS CONTROL MODULE WIRING
HARNESS-SIDE CONNECTOR
DRIVER-SIDE SIDE AIR BAG SENSOR NO.1
WIRING HARNESS-SIDE CONNECTOR
2A
2B
2C
2D
2E
2F
2G
2H
2I
2J
2L
2M
2O
2P
2R
2S
2T
2U
2V
2W
2Y
2X
2Z
2AA
1871-1U-06B(08-02).fm 40 ページ 2006年3月15日 水曜日 午前11時33分
ON-BOARD DIAGNOSTIC
08-02–41
08-02
Diagnostic procedure
STEP
INSPECTION
ACTION
1
INSPECT DRIVER-SIDE SIDE AIR BAG
SENSOR NO. 1 CONNECTOR
Warning
• Handling the air bag system
components improperly can
accidentally deploy the air bag
modules and pre-tensioner seat belts,
which may seriously injure you. Read
the service warnings and cautions
before handling the air bag system
components.
(See 08-10-3 AIR BAG SYSTEM
SERVICE WARNINGS.)
(See 08-10-5 AIR BAG SYSTEM
SERVICE CAUTIONS.)
• Turn the ignition switch to the LOCK position.
• Disconnect the negative battery cable and
wait for 1 min or more.
• Remove the B-pillar lower trim (driver-side).
(See 09-17-16 B-PILLAR LOWER TRIM
REMOVAL/INSTALLATION.)
• Disconnect the driver-side side air bag
sensor No. 1 connector.
• Is there any malfunction of the driver-side
side air bag sensor No. 1 connector?
Yes
Replace the air bag wiring harness.
No
Go to the next step.
1871-1U-06B(08-02).fm 41 ページ 2006年3月15日 水曜日 午前11時33分
ON-BOARD DIAGNOSTIC
08-02–42
End Of Sie
2
INSPECT WIRING HARNESS BETWEEN
DRIVER-SIDE SIDE AIR BAG SENSOR NO.1
AND SAS CONTROL MODULE
• Turn the ignition switch to the LOCK position.
• Disconnect the negative battery cable and
wait for 1 min or more.
• Remove the column cover. (See 09-17-8
COLUMN COVER REMOVAL/
INSTALLATION.)
• Disconnect the clock spring connector.
• Remove the glove compartment.(See 09-17-
8 GLOVE COMPARTMENT REMOVAL/
INSTALLATION.)
• Disconnect the passenger-side air bag
module connector.
• Disconnect the driver and passenger-side
seat connectors.
• Disconnect the driver and passenger-side
curtain air bag module connector.
• Remove the B-pillar lower trim. (See 09-17-
16 B-PILLAR LOWER TRIM REMOVAL/
INSTALLATION.)
• Disconnect the driver and passenger-side
pre-tensioner seat belt connectors.
• Disconnect the driver-side side air bag
sensor No.1 connector.
• Remove the console. (See 09-17-13
CONSOLE REMOVAL/INSTALLATION.)
• Disconnect the SAS control module
connector.
• Connect the negative battery cable.
• Inspect the wiring harnesses between SAS
control module connector terminal 2AA and
driver-side side air bag sensor No.1
connector terminal A, SAS control module
connector terminal 2Z and driver-side side
air bag sensor No.1 connector terminal B for
the following:
— Short to ground
— Short to power supply
— Open circuit
• Is the wiring harness normal?
Yes
Go to the next step.
No
Replace the air bag wiring harness.
3
INSPECT SAS CONTROL MODULE
• Turn the ignition switch to the LOCK position.
• Disconnect the negative battery cable and
wait for 1 min or more.
• Connect the SAS control module connector.
• Connect the driver-side side air bag sensor
No.1 connector.
• Turn the ignition switch to the ON position.
• Are DTCs B2444 and/or U2017 indicated?
Yes
Replace the SAS control module.
(See 08-10-10 SAS CONTROL MODULE REMOVAL/
INSTALLATION.)
No
DTC troubleshooting completed.
STEP
INSPECTION
ACTION
1871-1U-06B(08-02).fm 42 ページ 2006年3月15日 水曜日 午前11時33分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст