Mazda CX 7. Manual — part 431
ENTERTAINMENT
09-20–15
09-20
Accessory Socket Removal Note
1. While pressing a tape-wrapped flathead
screwdriver against the cap projection, pull the
accessory socket outward.
Cap Removal Note
1. While pressing the tabs, pull the cap outwards.
End Of Sie
ACCESSORY SOCKET INSPECTION
id092000800500
1. Connect a tester as shown in the figure and verify
that there is continuity.
• If the continuity cannot be verified, replace the
accessory socket.
End Of Sie
ACCESORY
SOCKET
CAP
PROJECTION
HOLE COVER
acxuuw00001015
TAB
TAB
acxuuw00001016
C
B
*
B
C
TERMINAL B
TERMINAL C
B6U0920W005
1871-1U-06B(09-20).fm 15 ページ 2006年3月15日 水曜日 午後12時49分
POWER SYSTEMS
09-21–1
09-21
09-21
POWER SYSTEMS
POWER SYSTEM LOCATION INDEX . . 09-21–1
FUSE SERVICE CAUTIONS . . . . . . . . . . 09-21–1
IGNITION SWITCH
REMOVAL/INSTALLATION. . . . . . . . . . 09-21–2
IGNITION SWITCH INSPECTION . . . . . . 09-21–2
KEY REMINDER SWITCH
REMOVAL/INSTALLATION. . . . . . . . . . 09-21–2
KEY REMINDER SWITCH
INSPECTION . . . . . . . . . . . . . . . . . . . . . 09-21–3
STEERING LOCK UNIT INSPECTION . . 09-21–3
Terminal Voltage Table (Reference) . . . 09-21–3
RELAY LOCATION . . . . . . . . . . . . . . . . . . 09-21–4
RELAY INSPECTION . . . . . . . . . . . . . . . . 09-21–4
Relay type . . . . . . . . . . . . . . . . . . . . . . . 09-21–4
Type A . . . . . . . . . . . . . . . . . . . . . . . . . . 09-21–5
Type B . . . . . . . . . . . . . . . . . . . . . . . . . . 09-21–5
End of Toc
WM: POWER SUPPLY SYSTEM
POWER SYSTEM LOCATION INDEX
id092100800700
.
End Of Sie
WM: FUSE
FUSE SERVICE CAUTIONS
id092100800400
Caution
• Determine and correct the cause of the burnt fuse before replacing it with the specified type. If the
fuse is replaced before doing this, it may burn again.
End Of Sie
WM: IGNITION SWITCH
5
4
3
1
2
acxuuw00002092
1
Main fuse block
(See 09-21-4 RELAY LOCATION.)
(See 09-21-4 RELAY INSPECTION.)
2
Relay block
(See 09-21-4 RELAY LOCATION.)
(See 09-21-4 RELAY INSPECTION.)
3
Ignition switch
(See 09-21-2 IGNITION SWITCH REMOVAL/
INSTALLATION)
(See 09-21-2 IGNITION SWITCH INSPECTION.)
4
Key reminder switch
(See 09-21-2 KEY REMINDER SWITCH
REMOVAL/INSTALLATION)
(See 09-21-3 KEY REMINDER SWITCH
INSPECTION.)
5
Steering lock unit
(See 09-21-3 STEERING LOCK UNIT
INSPECTION.)
1871-1U-06B(09-21).fm 1 ページ 2006年3月15日 水曜日 午後2時47分
POWER SYSTEMS
09-21–2
IGNITION SWITCH REMOVAL/INSTALLATION
id092100800200
1. Disconnect the negative battery cable.
2. Remove the column cover. (See 09-17-8 COLUMN COVER REMOVAL/INSTALLATION.)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
End Of Sie
IGNITION SWITCH INSPECTION
id092100800100
1. Verify that the continuity between the ignition
switch terminals is as indicated in the table.
• If not as indicated in the table, replace the
ignition switch.
End Of Sie
WM: KEY REMINDER SWITCH
KEY REMINDER SWITCH REMOVAL/INSTALLATION
id092100801000
1. Disconnect the negative battery cable.
2. Remove the column cover. (See 09-17-8 COLUMN COVER REMOVAL/INSTALLATION.)
3. Disconnect the key reminder switch connector.
4. Remove the key reminder switch.
5. Install in the reverse order of removal.
End Of Sie
1
Connector
2
Screw
3
Ignition switch
1
2
3
acxuuw00002093
A
B
D
C
E
F
START
START
LOCK
LOCK
ACC
ACC
C
D
E
F
A
B
ON
ON
acxuuw00002094
LOCK
ACC
ON
START
B
A
E
F
D
C
Ignition key
position
Terminal
: Continuity
acxuuw00002095
KEY REMINDER
SWITCH
STEERING LOCK
acxuuw00002096
1871-1U-06B(09-21).fm 2 ページ 2006年3月15日 水曜日 午後2時47分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст