Mazda CX 7. Manual — part 335
ON-BOARD DIAGNOSTIC [IMMOBILIZER SYSTEM (KEYLESS ENTRY SYSTEM)]
09-02C–11
09-02C
SECURITY LIGHT 15, DTC B1601/P1260[IMMOBILIZER SYSTEM (KEYLESS ENTRY SYSTEM)]
id0902e5801100
Diagnostic Procedure
End Of Sie
SECURITY LIGHT: 15
The instrument cluster has detected unregistered key ID number.
DTC: B1601/P1260
DETECTION CONDITION
• The instrument cluster has detected unregistered key ID number.
POSSIBLE CAUSE
• No keys have been registered after replacing the instrument cluster.
• Unregistered key used
• Attempt made to register a ninth key
• Instrument cluster malfunction
STEP
INSPECTION
ACTION
1
VERIFY NUMBER OF REGISTERED KEYS
• Using the M-MDS, perform the PID/data monitor
inspection and confirm the number of registered
keys.
(See 09-02C-4 PID/DATA MONITOR
TABLE[IMMOBILIZER SYSTEM (KEYLESS
ENTRY SYSTEM)].)
• Are one or more keys registered?
Yes
Go to the next step.
No
Go to Step 3.
2
VERIFY NUMBER OF REGISTERED KEYS
• Using the M-MDS, perform the PID/data monitor
inspection and confirm the number of registered
keys.
(See 09-02C-4 PID/DATA MONITOR
TABLE[IMMOBILIZER SYSTEM (KEYLESS
ENTRY SYSTEM)].)
• Are eight keys registered?
Yes
Using the M-MDS, clear the key ID numbers as
necessary, then go to the next step.
No
Go to the next step.
3
INSPECT INSTRUMENT CLUSTER
• Using the M-MDS, register the key ID number.
(See 09-14-20 IMMOBILIZER SYSTEM
COMPONENT REPLACEMENT/KEY ADDITION
AND CLEARING[KEYLESS ENTRY SYSTEM].)
Note
• Two or more keys must be registered to
start the engine.
• Using the registered key, turn the ignition switch
to the ON position.
• Is the DTC displayed again?
— Security light: 15
— M-MDS: B1601/P1260
Yes
Replace the instrument cluster and perform the
resetting procedure for the immobilizer system when
replacing the instrument cluster.
(See 09-22-2 INSTRUMENT CLUSTER REMOVAL/
INSTALLATION.)
(See 09-14-20 IMMOBILIZER SYSTEM COMPONENT
REPLACEMENT/KEY ADDITION AND
CLEARING[KEYLESS ENTRY SYSTEM].)
No
DTC troubleshooting completed.
1871-1U-06B(09-02C).fm 11 ページ 2006年3月15日 水曜日 午前11時39分
ON-BOARD DIAGNOSTIC [IMMOBILIZER SYSTEM (KEYLESS ENTRY SYSTEM)]
09-02C–12
SECURITY LIGHT 16, DTC U2510/P1260, U1147/P1260[IMMOBILIZER SYSTEM (KEYLESS ENTRY SYSTEM)]
id0902e5801200
Diagnostic Procedure
End Of Sie
SECURITY LIGHT 21, DTC B1213/P1260[IMMOBILIZER SYSTEM (KEYLESS ENTRY SYSTEM)]
id0902e5801300
Diagnostic Procedure
SECURITY
LIGHT: 16
DTC: U2510/P1260
Communication error between the instrument cluster and the PCM (no response)
DTC: U1147/P1260
Communication error between the instrument cluster and the PCM (mismatched
conditions)
DETECTION CONDITION
Instrument cluster DTC: U2510
• Communication error between the instrument cluster and the PCM (no response)
Instrument cluster DTC: U1147
• Communication error between the instrument cluster and the PCM (mismatched
conditions)
POSSIBLE CAUSE
• Malfunction in the wiring harness (CAN line) between the instrument cluster and the
PCM
• PCM malfunction
• Instrument cluster malfunction
STEP
INSPECTION
ACTION
1
VERIFY DTC
• Are either U1900 or U0073, or both, displayed,
by either the instrument cluster or the PCM, or
both?
Yes
Perform troubleshooting according to the corresponding
DTC inspection.
(See 09-02D-14 DTC U0073[MULTIPLEX
COMMUNICATION SYSTEM].)
No
Replace the instrument cluster and perform the
resetting procedure for the immobilizer system when
replacing the instrument cluster.
(See 09-22-2 INSTRUMENT CLUSTER REMOVAL/
INSTALLATION.)
(See 09-14-20 IMMOBILIZER SYSTEM COMPONENT
REPLACEMENT/KEY ADDITION AND
CLEARING[KEYLESS ENTRY SYSTEM].)
Go to the next step.
2
VERIFY DTC
• Using the registered key, turn the ignition switch
to the ON position.
• Is the DTC displayed?
— Security light: 16
— M-MDS: U2510 or U1147/P1260
Yes
Replace the PCM and perform the resetting procedure
for the immobilizer system when replacing the PCM.
(See 01-40-6 PCM REMOVAL/INSTALLATION[L3
WITH TC].)
(See 09-14-20 IMMOBILIZER SYSTEM COMPONENT
REPLACEMENT/KEY ADDITION AND
CLEARING[KEYLESS ENTRY SYSTEM].)
No
DTC troubleshooting completed.
SECURITY LIGHT: 21
Only one key ID number is registered.
DTC: B1213/P1260
DETECTION CONDITION
• Only one key is registered.
POSSIBLE CAUSE
• Only one registered key
STEP
INSPECTION
ACTION
1
VERIFY NUMBER OF REGISTERED KEYS
• Using the M-MDS, perform the PID/data monitor
inspection and confirm the number of registered
keys.
(See 09-02C-4 PID/DATA MONITOR
TABLE[IMMOBILIZER SYSTEM (KEYLESS
ENTRY SYSTEM)].)
• Are two or more keys registered?
Yes
Replace the instrument cluster and perform the
resetting procedure for the immobilizer system when
replacing the instrument cluster.
(See 09-22-2 INSTRUMENT CLUSTER REMOVAL/
INSTALLATION.)
(See 09-14-20 IMMOBILIZER SYSTEM COMPONENT
REPLACEMENT/KEY ADDITION AND
CLEARING[KEYLESS ENTRY SYSTEM].)
No
• Using the M-MDS, clear the key ID number and
register a new key if necessary.
(See 09-14-20 IMMOBILIZER SYSTEM
COMPONENT REPLACEMENT/KEY ADDITION
AND CLEARING[KEYLESS ENTRY SYSTEM].)
• Go to the next step.
1871-1U-06B(09-02C).fm 12 ページ 2006年3月15日 水曜日 午前11時39分
ON-BOARD DIAGNOSTIC [IMMOBILIZER SYSTEM (KEYLESS ENTRY SYSTEM)]
09-02C–13
09-02C
End Of Sie
SECURITY LIGHT 22, DTC B2141/P1260[IMMOBILIZER SYSTEM (KEYLESS ENTRY SYSTEM)]
id0902e5801400
Diagnostic Procedure
End Of Sie
2
VERIFY DTC
• Using the registered key, turn the ignition switch
to the ON position.
• Is the DTC displayed again?
— Security light: 21
— M-MDS: B1213/P1260
Yes
Replace the instrument cluster and perform the
resetting procedure for the immobilizer system when
replacing the instrument cluster.
(See 09-22-2 INSTRUMENT CLUSTER REMOVAL/
INSTALLATION.)
(See 09-14-20 IMMOBILIZER SYSTEM COMPONENT
REPLACEMENT/KEY ADDITION AND
CLEARING[KEYLESS ENTRY SYSTEM].)
No
DTC troubleshooting completed.
STEP
INSPECTION
ACTION
SECURITY LIGHT: 22
Communication error between the instrument cluster and the PCM (data transfer error)
DTC: B1241/P1260
DETECTION CONDITION
• Communication error between the instrument cluster and the PCM (data transfer error)
POSSIBLE CAUSE
• Malfunction in the wiring harness (CAN line) between the instrument cluster and the PCM
• Instrument cluster malfunction
• PCM malfunction
STEP
INSPECTION
ACTION
1
VERIFY DTC
• Are either U1900 or U0073, or both displayed, by
either the instrument cluster or the PCM, or both?
Yes
Perform troubleshooting according to the
corresponding DTC inspection.
(See 09-02D-14 DTC U0073[MULTIPLEX
COMMUNICATION SYSTEM].)
No
Go to the next step.
2
VERIFY DTC
• Using the registered key, turn the ignition switch to
the ON position.
• Is the DTC displayed?
— Security light: 22
— M-MDS: B2141/P1260
Yes
• Replace the PCM and perform the resetting
procedure for the immobilizer system when
replacing the PCM.
(See 09-14-20 IMMOBILIZER SYSTEM
COMPONENT REPLACEMENT/KEY ADDITION
AND CLEARING[KEYLESS ENTRY SYSTEM].)
• Go to the next step.
No
DTC troubleshooting completed.
3
EXAMINE INSTRUMENT CLUSTER AND PCM
• Is the DTC displayed again?
— Security light: 22
— M-MDS: B2141/P1260
Yes
• Replace the instrument cluster and perform the
resetting procedure for the immobilizer system
when replacing the instrument cluster.
(See 09-22-2 INSTRUMENT CLUSTER
REMOVAL/INSTALLATION.)
(See 09-14-20 IMMOBILIZER SYSTEM
COMPONENT REPLACEMENT/KEY ADDITION
AND CLEARING[KEYLESS ENTRY SYSTEM].)
• Go to the next step.
No
DTC troubleshooting completed.
4
EXAMINE PCM
• Is the DTC displayed again?
— Security light: 22
— M-MDS: B2141/P1260
Yes
• Replace the PCM and perform the resetting
procedure for the immobilizer system when
replacing the PCM.
(See 01-40-6 PCM REMOVAL/
INSTALLATION[L3 WITH TC].)
(See 09-14-20 IMMOBILIZER SYSTEM
COMPONENT REPLACEMENT/KEY ADDITION
AND CLEARING[KEYLESS ENTRY SYSTEM].)
No
DTC troubleshooting completed.
1871-1U-06B(09-02C).fm 13 ページ 2006年3月15日 水曜日 午前11時39分
ON-BOARD DIAGNOSTIC [IMMOBILIZER SYSTEM (KEYLESS ENTRY SYSTEM)]
09-02C–14
SECURITY LIGHT 23, DTC B2139/P1260[IMMOBILIZER SYSTEM (KEYLESS ENTRY SYSTEM)]
id0902e5801500
Diagnostic Procedure
End Of Sie
DTC B1342[IMMOBILIZER SYSTEM (KEYLESS ENTRY SYSTEM)]
id0902e5801600
Diagnostic procedure
End Of Sie
SECURITY LIGHT: 23
ID number data in the PCM and the instrument cluster do not match.
DTC: B2139/P1260
DETECTION CONDITION
• ID number data in the instrument cluster and the PCM are different.
POSSIBLE CAUSE
• Necessary procedures were not performed using the M-MDS after replacing the PCM.
• Instrument cluster malfunction
• PCM malfunction
STEP
INSPECTION
ACTION
1
VERIFY DTC
• Are either U1900 or U0073, or both, displayed, by
either the instrument cluster or the PCM, or both?
Yes
Perform troubleshooting according to the
corresponding DTC inspection.
(See 09-02D-14 DTC U0073[MULTIPLEX
COMMUNICATION SYSTEM].)
No
Go to the next step.
2
EXAMINE INSTRUMENT CLUSTER AND PCM
• Perform procedures for when replacing the PCM
only.
(See 09-14-20 IMMOBILIZER SYSTEM
COMPONENT REPLACEMENT/KEY ADDITION
AND CLEARING[KEYLESS ENTRY SYSTEM].)
• Using the registered key, turn the ignition switch to
the ON position.
• Is the DTC displayed?
— Security light: 23
— M-MDS: B2139/P1260
Yes
• Replace the instrument cluster and perform the
resetting procedure for the immobilizer system
when replacing the instrument cluster.
(See 09-22-2 INSTRUMENT CLUSTER
REMOVAL/INSTALLATION.)
(See 09-14-20 IMMOBILIZER SYSTEM
COMPONENT REPLACEMENT/KEY ADDITION
AND CLEARING[KEYLESS ENTRY SYSTEM].)
• Go to the next step.
No
DTC troubleshooting completed.
3
VERIFY DTC
• Is the DTC displayed again?
— Security light: 23
— M-MDS: B2139/P1260
Yes
• Replace the PCM and perform the resetting
procedure for the immobilizer system when
replacing the PCM.
(See 01-40-6 PCM REMOVAL/
INSTALLATION[L3 WITH TC].)
(See 09-14-20 IMMOBILIZER SYSTEM
COMPONENT REPLACEMENT/KEY ADDITION
AND CLEARING[KEYLESS ENTRY SYSTEM].)
No
DTC troubleshooting completed.
DTC B1342
ECU is faulted
DETECTION
CONDITION
Instrument cluster malfunction
POSSIBLE
CAUSE
• Instrument cluster malfunction
ACTION
Replace the instrument cluster.
(See 09-22-2 INSTRUMENT CLUSTER REMOVAL/INSTALLATION.)
1871-1U-06B(09-02C).fm 14 ページ 2006年3月15日 水曜日 午前11時39分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст