Mazda CX 7. Manual — part 323
AIR BAG SYSTEM
08-10–29
08-10
11. Press the activation switch on the SST
(Deployment tool) to operate (deploy) the curtain
air bag module.
12. Disconnect the SSTs (Deployment tool) from the
SSTs (Adapter harness).
Pre-tensioner Seat Belt
1. Remove the pre-tensioner seat belt.
(See 08-11-2 FRONT SEAT BELT REMOVAL/INSTALLATION.)
2. Connect the SST (Adapter harness) to the pre-
tensioner seat belt as shown in the figure.
3. Put the pre-tensioner seat belt inside the tire and
secure it to the tire by wrapping a wire (cross
section of 1.25mm
2
{0.002in
2
} or more) through
the tire and the bolt installation holes at least 4
times.
Warning
• If the pre-tensioner seat belt is not
properly installed to the tire, serious
injury may occur when the pre-tensioner
part is operated (deployed). When
installing the pre-tensioner seat belt to
the tire, make sure the pre-tensioner part
is inside the tire.
4. Stack the tire with the pre-tensioner seat belt on
to of two tires without wheels. Stack a tire without
a wheel on top of the tire with the pre-tensioner
seat belt, and then stack another tire with a wheel
on the very top.
49 H066 002
ACTIVATION
SWITCH
acxuuw00001267
49 L066 002
acxuuw00001273
WIRE
TIRE
PRE-TENSIONER
SEAT BELT
acxuuw00001291
TIRE WITH
WHEEL
TIRE
WITHOUT
WHEEL
TIRE WITH
PRE-TENSIONER
SEAT BELT
acxuuw00001292
1871-1U-06B(08-10).fm 29 ページ 2006年3月15日 水曜日 午前11時36分
AIR BAG SYSTEM
08-10–30
5. Secure the tires with wire.
6. Connect the SST (Deployment tool) to the SST
(Adapter harness).
7. Connect the SST (Deployment tool) to the
battery. Connect the power supply red clip to the
positive battery terminal, and the black clip to the
negative battery terminal.
8. Verify that the red lamp on the SST (Deployment
tool) is illuminated.
9. Verify that all persons are standing at least 6 m
{20 ft} away from the vehicle.
10. Press the activation switch on the SST
(Deployment tool) to operate (deploy) the pre-
tensioner seat belt.
11. Disconnect the SSTs (Deployment tool) from the
SSTs (Adapter harness).
End Of Sie
AIR BAG MODULE AND PRE-TENSIONER SEAT BELT DISPOSAL PROCEDURES
id081000801200
Warning
• A live (undeployed) air bag module or pre-tensioner seat belt may accidentally operate (deploy)
when it is disposed of and cause serious injury. Always refer to the “AIR BAG MODULE AND PRE-
TENSIONER SEAT BELT DEPLOYMENT PROCEDURES” and dispose of air bag modules and pre-
tensioner seat belts in a deployed condition.
• The air bag modules and the pre-tensioner seat belts are very hot immediately after they are
deployed. You can be burned. Do not touch an air bag module and pre-tensioner seat belt for at
least 15 min after deployment.
• Pouring water on the deployed air bag module and pre-tensioner seat belt is dangerous. The water
will mix with the residual gases to form a gas that can make breathing difficult. Do not pour water
on the deployed air bag module and pre-tensioner seat belt.
• The deployed air bag module or pre-tensioner seat belt may contain deposits of sodium
hydroxide, a caustic byproduct of the gas-generated combustion. If this substance gets into your
eyes or on your hands, it can cause irritation and itching. When handling the deployed air bag
module and pre-tensioner seat belt, wear gloves and safety glasses.
• Due to the adoption of 2-step deployment control in both the driver and passenger-side air bag
modules, depending on the impact force, it is possible that inflator No.2 might not operate
(deploy). Before disposing of the air bag module, always follow the inflator deployment
procedures and verify the complete operation (deployment) of inflators No.1 and 2.
acxuuw00001276
49 H066 002
49 L066 002
acxuuw00001293
49 H066 002
ACTIVATION
SWITCH
acxuuw00001267
1871-1U-06B(08-10).fm 30 ページ 2006年3月15日 水曜日 午前11時36分
AIR BAG SYSTEM
08-10–31
08-10
1. Remove the deployed air bag module or pre-tensioner seat belt.
2. Put the air bag module or pre-tensioner seat belt
in a plastic bag, seal the bag, and then dispose of
it.
End Of Sie
WM: DEPLOYMENT TOOL
INSPECTION OF SST (DEPLOYMENT TOOL)
id081000801000
1. Before using the SST (49 H066 002), inspect its
operation.
Inspection Procedure
1. Follow the steps below to inspect the SST (49 H066 002).
• If not as indicated in the table, replace the SST (49 H066 002) because it has a malfunction.
Warning
• Do not use a malfunctioning SST (49 H066 002), otherwise it could cause the air bag module or
pre-tensioner seat belt to accidentally operate (deploy).
Caution
• Because the permissible voltage for the SST (49 H066 002) is 12 V, do not connect a 24 V power
source because it will damage the SST. Always connect only a 12 V power source.
End Of Sie
acxuuw00002421
49 H066 002
GREEN
LIGHT
CONNECTOR A
RED LIGHT
ACTIVATION SWITCH
CONNECTOR B
POWER SUPPLY CLIP
acxuuw00002419
Step
Inspection procedure
Light condition
Green
Red
1
Connect the power supply
red clip to the positive
battery terminal, and the
black clip to the negative
battery terminal.
On
Off
2
Connect connectors A and
B.
Off
On
3
Press the activation switch.
On
Off
49 H066 002
49 H066 002
RED CLIP
BLACK CLIP
ACTIVATION
SWITCH
CONNECTOR B
CONNECTOR A
acxuuw00002420
1871-1U-06B(08-10).fm 31 ページ 2006年3月15日 水曜日 午前11時36分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст