Mazda CX 7. Manual — part 324
![](/vehicles/rke/eetan/dot/utatst.png)
SEAT BELT
08-11–1
08-11
08-11
SEAT BELT
LOCATION INDEX. . . . . . . . . . . . . . . . . . 08-11–1
FRONT SEAT BELT
REMOVAL/INSTALLATION. . . . . . . . . . 08-11–2
Connector Removal Note. . . . . . . . . . . 08-11–3
ADJUSTER ANCHOR
REMOVAL/INSTALLATION. . . . . . . . . . 08-11–3
REAR SEAT BELT
REMOVAL/INSTALLATION. . . . . . . . . . 08-11–3
REAR CENTER SEAT BELT
REMOVAL/INSTALLATION. . . . . . . . . . 08-11–4
SEAT BELT INSPECTION. . . . . . . . . . . . 08-11–4
Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . 08-11–4
ELR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 08-11–4
ALR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 08-11–5
Load Limiter Retractor. . . . . . . . . . . . . . 08-11–5
FRONT BUCKLE
REMOVAL/INSTALLATION . . . . . . . . . . 08-11–5
REAR BUCKLE
REMOVAL/INSTALLATION . . . . . . . . . . 08-11–6
BUCKLE SWITCH INSPECTION . . . . . . . 08-11–6
CHILD-RESTRAINT SEAT ANCHOR
REMOVAL/INSTALLATION . . . . . . . . . . 08-11–6
End of Toc
WM: SEAT BELT
LOCATION INDEX
id081100800200
.
End Of Sie
WM: FRONT SEAT BELT
5
4
3
6
1
2
7
acxuuw00002082
1
Front seat belt
(See 08-11-2 FRONT SEAT BELT REMOVAL/
INSTALLATION.)
(See 08-11-4 SEAT BELT INSPECTION.)
2
Adjuster anchor
(See 08-11-3 ADJUSTER ANCHOR REMOVAL/
INSTALLATION.)
3
Front buckle
(See 08-11-5 FRONT BUCKLE REMOVAL/
INSTALLATION.)
(See 08-11-6 BUCKLE SWITCH INSPECTION.)
4
Rear seat belt
(See 08-11-3 REAR SEAT BELT REMOVAL/
INSTALLATION.)
(See 08-11-4 SEAT BELT INSPECTION.)
5
Rear center seat belt
(See 08-11-4 REAR CENTER SEAT BELT
REMOVAL/INSTALLATION.)
(See 08-11-4 SEAT BELT INSPECTION.)
6
Rear buckle
(See 08-11-6 REAR BUCKLE REMOVAL/
INSTALLATION.)
7
Child-restraint seat anchor
(See 08-11-6 CHILD-RESTRAINT SEAT ANCHOR
REMOVAL/INSTALLATION.)
1871-1U-06B(08-11).fm 1 ページ 2006年3月15日 水曜日 午前11時37分
![](/vehicles/rke/eetan/dot/zngl.png)
SEAT BELT
08-11–2
FRONT SEAT BELT REMOVAL/INSTALLATION
id081100800600
Warning
• Handling the front seat belt (pre-tensioner seat belt) improperly can accidentally deploy the pre-
tensioner seat belt, which may seriously injure you. Read the air bag system service warnings and
cautions before handling the front seat belt. (See 08-10-3 AIR BAG SYSTEM SERVICE WARNINGS.)
(See 08-10-5 AIR BAG SYSTEM SERVICE CAUTIONS.)
Warning
• The side air bag sensor is attached to the lower part of the B-pillar. When working around the B-
pillar, disconnect the negative battery cable avoiding excessive impact to the lower part of the B-
pillar.
Caution
• The ELR (emergency locking retractor) has a spring that will unwind if the retractor cover is
removed. The spring cannot be rewound by hand. If this occurs, the ELR will not work properly.
Therefore, do not disassemble the retractor.
1. Turn the ignition switch to the LOCK position.
2. Disconnect the negative battery cable and wait for 1min or more.
3. Remove the front scuff plate inner. (See 09-17-19 FRONT SCUFF PLATE REMOVAL/INSTALLATION.)
4. Remove the rear scuff plate inner. (See 09-17-19 REAR SCUFF PLATE REMOVAL/INSTALLATION.)
5. Remove the B-pillar lower trim. (See 09-17-16 B-PILLAR LOWER TRIM REMOVAL/INSTALLATION.)
6. Remove in the order indicated in the table.
.
7. Install in the reverse order of removal.
8. Turn the ignition switch to the ON position.
9. Verify that the air bag system warning light illuminates for approx. 6 s and goes out.
• If the air bag system warning light dose not operate, refer to the on-board diagnostic system (air bag
system) and perform inspection of the system.
N·m {kgf·m, ft·lbf}
38.3—78.4
{3.90—7.99,
28.3—57.8}
38.3—78.4
{3.90—7.99,
28.3—57.8}
36.3—54.0
{3.71—5.50,
26.8—39.8}
PASSENGER'S SEAT
FRONT
8.8—12.8 N·m
{89.8—130 kgf·cm,
77.9—113 in·lbf}
5
4
3
1
2
1
1
2
acxuuw00001026
1
Cover
2
Bolt A
3
Bolt B
4
Front seat belt
5
Connector
(See 08-11-3 Connector Removal Note.)
1871-1U-06B(08-11).fm 2 ページ 2006年3月15日 水曜日 午前11時37分
![](/vehicles/rke/eetan/dot/ereree.png)
SEAT BELT
08-11–3
08-11
Connector Removal Note
1. Using a flathead screwdriver, pry out the
connector stopper plate.
2. Disconnect the connector.
End Of Sie
ADJUSTER ANCHOR REMOVAL/INSTALLATION
id081100802000
Warning
• The side air bag sensor is attached to the lower part of the B-pillar. When working around the B-
pillar, disconnect the negative battery cable or work carefully, avoiding excessive impact to the
lower part of the B-pillar.
1. Turn the ignition switch to the LOCK position.
2. Disconnect the negative battery cable.
3. Remove the following parts:
(1) Front seat belt upper anchor installation bolt (See 08-11-2 FRONT SEAT BELT REMOVAL/
INSTALLATION.)
(2) Front scuff plate inner (See 09-17-19 FRONT SCUFF PLATE REMOVAL/INSTALLATION.)
(3) Rear scuff plate inner (See 09-17-19 REAR SCUFF PLATE REMOVAL/INSTALLATION.)
(4) B-pillar lower trim (See 09-17-16 B-PILLAR LOWER TRIM REMOVAL/INSTALLATION.)
(5) B-pillar upper trim (See 09-17-16 B-PILLAR UPPER TRIM REMOVAL/INSTALLATION.)
4. Remove in the order indicated in the table.
.
5. Install in the reverse order of removal.
End Of Sie
WM: REAR SEAT BELT
REAR SEAT BELT REMOVAL/INSTALLATION
id081100800800
Note
• Rear seat belts are built into the rear seat back. See rear seat disassembly/assembly to removal/
installation the rear seat belt. (See 09-13-8 REAR SEAT DISASSEMBLY/ASSEMBLY.)
End Of Sie
PRE-TENSIONER
SEAT BELT
CONNECTOR
STOPPER
PLATE
acxuuw00001027
1
Bolt
2
Adjuster anchor
1
2
38.2—78.4
{3.90—7.99,
28.2—57.8}
N·m {kgf·m, ft·lbf}
1
38.2—78.4
{3.90—7.99,
28.2—57.8}
acxuuw00002087
1871-1U-06B(08-11).fm 3 ページ 2006年3月15日 水曜日 午前11時37分
![](/vehicles/rke/eetan/dot/aththe.png)
SEAT BELT
08-11–4
REAR CENTER SEAT BELT REMOVAL/INSTALLATION
id081100800900
Caution
• The ELR (emergency locking retractor) has a spring that will unwind if the retractor cover is
removed. The spring cannot be rewound by hand. If this occurs, the ELR will not work properly.
Therefore, do not disassemble the retractor.
1. Remove the following parts:
(1) A-pillar lower trim (See 09-17-16 A-PILLAR LOWER TRIM REMOVAL/INSTALLATION.)
(2) A-pillar trim (See 09-17-15 A-PILLAR TRIM REMOVAL/INSTALLATION.)
(3) Front scuff plate inner (See 09-17-19 FRONT SCUFF PLATE REMOVAL/INSTALLATION.)
(4) Rear scuff plate inner (See 09-17-19 REAR SCUFF PLATE REMOVAL/INSTALLATION.)
(5) B-pillar lower trim (See 09-17-16 B-PILLAR LOWER TRIM REMOVAL/INSTALLATION.)
(6) Front seat belt upper anchor installation bolt (See 08-11-2 FRONT SEAT BELT REMOVAL/
INSTALLATION.)
(7) B-pillar upper trim (See 09-17-16 B-PILLAR UPPER TRIM REMOVAL/INSTALLATION.)
(8) Rear seat (See 09-13-7 REAR SEAT REMOVAL/INSTALLATION.)
(9) Sub trunk box (See 09-17-25 SUB TRUNK BOX REMOVAL/INSTALLATION.)
(10)Trunk end trim (See 09-17-24 TRUNK END TRIM REMOVAL/INSTALLATION.)
(11)Trunk side trim (See 09-17-24 TRUNK SIDE TRIM REMOVAL/INSTALLATION.)
(12)C-pillar trim (See 09-17-17 C-PILLAR TRIM REMOVAL/INSTALLATION.)
(13)D-pillar trim (See 09-17-18 D-PILLAR TRIM REMOVAL/INSTALLATION.)
(14)Map light (See 09-18-22 MAP LIGHT REMOVAL/INSTALLATION.)
(15)Sunvisor (See 09-17-26 SUNVISOR REMOVAL/INSTALLATION.)
(16)Assist handle (See 09-17-27 ASSIST HANDLE REMOVAL/INSTALLATION.)
(17)Headliner (See 09-17-27 HEADLINER REMOVAL/INSTALLATION.)
2. Remove in the order indicated in the table.
3. Install in the reverse order of removal.
End Of Sie
WM: SEAT BELT
SEAT BELT INSPECTION
id081100800300
Belt
1. Verify that the belt is installed properly with no twists or kinks.
2. Verify that there is no damage to the seat belt and no deformation of the metal fittings.
• If there is any malfunction, replace the seat belt.
ELR
1. Verify that the belt can be pulled out smoothly,
and that it retracts smoothly.
• If there is any malfunction, replace the seat
belt.
2. Verify that the retractor locks when the belt is
pulled quickly.
• If there is any malfunction, replace the seat
belt.
3. Remove the retractor.
1
Bolt
2
Rear center seat belt
38.3—78.4
{3.90—7.99,
28.3—57.8}
1
2
N·m {kgf·m, ft·lbf}
acxuuw00001031
acxuuw00002083
1871-1U-06B(08-11).fm 4 ページ 2006年3月15日 水曜日 午前11時37分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст