Mazda CX 7. Manual — part 151
CONTROL SYSTEM [L3 WITH TC]
01-40–45
01-40
CAMSHAFT POSITION (CMP) SENSOR REMOVAL/INSTALLATION[L3 WITH TC]
id014039801500
Caution
• When replacing the CMP sensor, make sure there is no foreign material on it such as metal
shavings. If it is installed with foreign material, the sensor output signal will malfunction resulting
from fluctuation in magnetic flux and cause a deterioration in engine control.
1. Disconnect the negative battery cable.
2. Remove the charge air cooler duct. (See01-13-5 INTAKE AIR SYSTEM REMOVAL/INSTALLATION[L3 WITH
TC].)
3. Remove the charge air cooler cover. (See01-13-5 INTAKE AIR SYSTEM REMOVAL/INSTALLATION[L3 WITH
TC].)
4. Disconnect the CMP sensor connector.
5. Remove the CMP sensor installation bolt.
6. Remove the CMP sensor from the cylinder head
cover.
7. Install in the reverse order of removal.
Tightening torque
5.5— 7.5 N·m {57— 76 kgf·cm, 49— 66 in·lbf}
End Of Sie
CAMSHAFT POSITION (CMP) SENSOR INSPECTION[L3 WITH TC]
id014039801400
Note
• Before performing the following inspection, make sure to follow the procedure as indicated in the
troubleshooting flowchart. (See 00-00-3 HOW TO USE THIS MANUAL.)
Visual Inspection
1. Disconnect the negative battery cable.
2. Remove the CMP sensor. (See01-40-45 CAMSHAFT POSITION (CMP) SENSOR REMOVAL/
INSTALLATION[L3 WITH TC].)
3. Verify that there are no metal shavings on the sensor.
• If the monitor item condition/specification (reference) is not within the specification even though there is no
malfunction, carry out the “Circuit Open/Short Inspection”.
Voltage Inspection
1. Idle the engine.
Caution
• Water penetrating the connector will cause sensor malfunction. To prevent this, be careful not to
damage the wiring harnesses or the waterproof connector so as to cause water penetration.
CMP SENSOR
acxuuw00000090
1871-1U-06B(01-40).fm 45 ページ 2006年3月15日 水曜日 午前10時53分
CONTROL SYSTEM [L3 WITH TC]
01-40–46
2. Measure the output voltage using an
oscilloscope.
• If not within the specification, replace the
CMP sensor.
• If the monitor item condition/specification
(reference) is not within the specification,
even though the voltage is within the
specification, carry out the “Circuit Open/
Short Inspection”.
Voltage
*
: Output voltage varies with camshaft rotation.
Circuit Open/Short Inspection
1. Inspect the following wiring harnesses for an open or short circuit. (Continuity check)
Terminal
Voltage (V)
Condition
A
B+
Under any condition
B
Below 1.0
Under any condition
C
4.8 or more
High output*
0.8 or less
Low output*
A
B
CMP SENSOR
WIRING HARNESS SIDE CONNECTOR
C
acxuuw00000087
A
B
CMP SENSOR
WIRING HARNESS SIDE CONNECTOR
C
acxuuw00000087
FUSE BOX
(MAIN RELAY)
A
E
B
D
FRONT
acxuuw00000538
2BE 2BA 2AW 2AS 2AO 2AK 2AG 2AC 2Y 2U 2Q 2M
2E
2A
2I
2BH 2BD 2AZ 2AV 2AR 2AN 2AJ 2AF 2AB 2X 2T 2P
2H
2D
2L
2BG 2BC 2AY 2AU 2AQ 2AM 2AI 2AE 2AA 2W 2S 2O
2G
2C
2K
2BF 2BB 2AX 2AT 2AP 2AL 2AH 2AD 2Z
2V 2R 2N
2F
2B
2J
1BE 1BA 1AW 1AS 1AO 1AK 1AG 1AC 1Y 1U 1Q 1M
1E
1A
1I
1BH 1BD 1AZ 1AV 1AR 1AN 1AJ 1AF 1AB 1X
1T
1P
1H
1D
1L
1BG 1BC 1AY 1AU 1AQ 1AM 1AI 1AE 1AA 1W 1S 1O
1G
1C
1K
1BF 1BB 1AX 1AT 1AP 1AL 1AH 1AD 1Z
1V
1R 1N
1F
1B
1J
PCM
WIRING HARNESS-SIDE CONNECTOR
acxuuw00000089
1871-1U-06B(01-40).fm 46 ページ 2006年3月15日 水曜日 午前10時53分
CONTROL SYSTEM [L3 WITH TC]
01-40–47
01-40
Open circuit
• If there is no continuity, the circuit is open. Repair or replace the wiring harness.
— CMP sensor terminal A and main relay terminal E
— CMP sensor terminal B and PCM terminal 2P
— CMP sensor terminal C and PCM terminal 2S
Short circuit
• If there is continuity, the circuit is shorted. Repair or replace the wiring harness.
— CMP sensor terminal A and body ground
— CMP sensor terminal B and power supply
— CMP sensor terminal C and body ground
— CMP sensor terminal C and power supply
End Of Sie
WM: KNOCK SENSOR
KNOCK SENSOR (KS) REMOVAL/INSTALLATION[L3 WITH TC]
id014039802900
Caution
• Be careful not to impact the sensor.
• Verify that there is no debris between the sensor and the cylinder block before installing.
1. Disconnect the negative battery cable.
2. Remove the intake manifold. (See01-13-5 INTAKE AIR SYSTEM REMOVAL/INSTALLATION[L3 WITH TC])
3. Remove the KS attachment bolt to remove the
KS.
4. Install in the reverse order of removal.
Tightening torque
16— 24 N·m {1.7— 2.4 kgf·m, 12— 17 ft·lbf}
End Of Sie
KNOCK SENSOR (KS) INSPECTION[L3 WITH TC]
id014039802800
Note
• Before performing the following inspection, make sure to follow the procedure as indicated in the
troubleshooting flowchart. (See 00-00-3 HOW TO USE THIS MANUAL.)
Resistance Inspection
1. Turn the ignition switch to the LOCK position.
2. Disconnect the KS connector.
3. Measure the resistance between KS terminals A and B using a tester.
• If not as specified, replace the KS. (See01-40-47 KNOCK SENSOR (KS) REMOVAL/INSTALLATION[L3
WITH TC].)
• If the KS is normal, but the PID value is out of specification, perform the “Circuit Open/Short Inspection”.
Specification
Approx. 4.87 megohms
VIEW A
A
KS
acxuuw00001859
1871-1U-06B(01-40).fm 47 ページ 2006年3月15日 水曜日 午前10時53分
CONTROL SYSTEM [L3 WITH TC]
01-40–48
Circuit Open/Short Inspection
1. Disconnect the PCM connector. (See01-40-6 PCM REMOVAL/INSTALLATION[L3 WITH TC].)
2. Inspect the following wiring harnesses for an open or short circuit. (Continuity check)
Open circuit
• If there is no continuity, there is an open circuit. Repair or replace the wiring harness.
— KS terminal A and PCM terminal 2U
— KS terminal B and PCM terminal 2V
Short circuit
• If there is continuity, there is a short circuit. Repair or replace the wiring harness.
— KS terminal A and power supply
— KS terminal A and body ground
— KS terminal B and power supply
— KS terminal B and body ground
End Of Sie
WM: FUEL PRESSURE SENSOR
BAROMETRIC PRESSURE (BARO) SENSOR INSPECTION[L3 WITH TC]
id014039801100
Note
• Before performing the following inspection, make sure to follow the procedure as indicated in the
troubleshooting flowchart. (See00-00-3 HOW TO USE THIS MANUAL.)
1. Connect the M-MDS to the DLC-2.
2. Turn the ignition switch to the ON position.
3. Select BARO on the M-MDS.
4. Verify that the BARO PID (pressure) and
barometric pressure are practically equal.
• If not as verified, replace the PCM. (See01-
40-6 PCM REMOVAL/INSTALLATION[L3
WITH TC].)
End Of Sie
A
B
KS
WIRING HARNESS SIDE CONNECTOR
acxuuw00000111
2BE 2BA 2AW 2AS 2AO 2AK 2AG 2AC 2Y 2U 2Q 2M
2E
2A
2I
2BH 2BD 2AZ 2AV 2AR 2AN 2AJ 2AF 2AB 2X 2T 2P
2H
2D
2L
2BG 2BC 2AY 2AU 2AQ 2AM 2AI 2AE 2AA 2W 2S 2O
2G
2C
2K
2BF 2BB 2AX 2AT 2AP 2AL 2AH 2AD 2Z
2V 2R 2N
2F
2B
2J
1BE 1BA 1AW 1AS 1AO 1AK 1AG 1AC 1Y 1U 1Q 1M
1E
1A
1I
1BH 1BD 1AZ 1AV 1AR 1AN 1AJ 1AF 1AB 1X
1T
1P
1H
1D
1L
1BG 1BC 1AY 1AU 1AQ 1AM 1AI 1AE 1AA 1W 1S 1O
1G
1C
1K
1BF 1BB 1AX 1AT 1AP 1AL 1AH 1AD 1Z
1V
1R 1N
1F
1B
1J
PCM
WIRING HARNESS-SIDE CONNECTOR
acxuuw00000112
DLC-2
acxuuw00000083
1871-1U-06B(01-40).fm 48 ページ 2006年3月15日 水曜日 午前10時53分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст