Mazda CX 7. Manual — part 152
TECHNICAL DATA [L3 WITH TC]
01-50–1
01-50
01-50
TECHNICAL DATA [L3 WITH TC]
ENGINE TECHNICAL DATA
[L3 WITH TC] . . . . . . . . . . . . . . . . . . . . 01-50–1
End of Toc
WM: ENGINE
ENGINE TECHNICAL DATA[L3 WITH TC]
id015039800100
Item
Specification
Standard valve clearance [Engine cold]
IN: 0.22—0.28 mm {0.0087—0.011 in}
EX: 0.27—0.33 mm {0.011—0.012 in}
Compression
Standard:1,280 kPa {13.1 kgf/cm
2
, 185.65 psi}[250rpm]
Minimum:896 kPa {9.14 kgf/cm
2
, 129.96 psi}[250rpm]
Maximum difference between cylinders:196.1 kPa {2.0 kgf/cm
2
, 28.5
psi}
Cylinder head bolt length
Standard
144.7—145.3 mm {5.697—5.720 in}
Maximum:
146 mm {5.74 in}
Front oil seal press-in amount
0—0.5 mm {0—0.019 in}
OCV resistance
6.9—7.9 ohms [20°C {68°F}]
Ignition timing
Approx. BTDC 10°
Idle speed (P, N position)
No load: 650—750 rpm
Electrical load on
*1
: 650—750 rpm
P/S operation: 650—750 rpm
A/C operation: 650—750 rpm
Idle speed (D position)
No load: 575—675 rpm
Electrical load on
*1
: 600—700 rpm
P/S operation: 650—750 rpm
A/C operation: 650—750 rpm
Idle mixture
HC concentration: Within the regulation
CO concentration: Within the regulation
Oil pressure (reference value) [oil temperature: 100 °C
{212 °F}]
297—551 kPa {3.03—5.61 kgf/cm
2
, 43.1—79.9 psi} [3,000 rpm]
Engine oil capacity (approx. quantity)
Oil replacement: 5.3 L {5.6 US qt, 4.7 Imp qt}
Oil and oil filter replacement: 5.7 L {6.0 US qt, 5.0 Imp qt}
Total (dry engine): 6.4 L {6.8 US qt, 5.6 Imp qt}
Engine coolant capacity (approx. quantity)
9.0 L {9.5 US qt, 7.9 Imp qt}
Cooling fan motor No.1, No.2 standard current
17.5—22.5 A
Cooling system cap valve opening pressure
112.8—142.2 kPa {1.15—1.45 kgf/cm
2
, 16.4—20.6 psi}
Thermostat initial-opening temperature
80—84 °C {176—183 °F}
Thermostat full-open temperature
97 °C {207 °F}
Thermostat full-open lift
More than 8.0 mm {0.31 in}
Fuel line pressure
410—490 kPa {4.2—4.9 kgf/cm
2
, 60—71 psi}
Fuel pump hold pressure
More than 230 kPa {2.3 kgf/cm
2
, 33 psi}
Fuel injector resistance
1.0—1.2 ohms [20 °C {68 °F}]
Battery electrolyte specific gravity [20 °C {68 °F}]
1.22—1.29
Battery load test current
55D23L (48): 180 A
80D26L (55): 195 A
Battery back-up current
Vehicles with immobilizer system: 55—65 mA
Vehicles without immobilizer system: 60 mA or less
Battery slow charge current
55D23L (48): 4.5—5.5 A
80D26L (55): 5.5—6.5 A
Battery quick charge current [30 min]
55D23L (48): 30 A
80D26L (55): 35 A
Generator standard voltage [IG-ON]
Terminal B: B+
Terminal P: Approx. 1 V or less
Terminal D: Approx. 0 V
1871-1U-06B(01-50).fm 1 ページ 2006年3月15日 水曜日 午前10時55分
TECHNICAL DATA [L3 WITH TC]
01-50–2
*1 : When the following electrical loads are on: Headlights, rear defroster, cooling fan No.1, cooling fan No.2, and
the blower motor (2-step or more.)
Engine oil specification
End Of Sie
Generator standard voltage [Idle, 20 °C {68 °F}]
Terminal B: 13—15 V
Terminal P: Approx. 3—8 V
Terminal D: Turn the electrical loads (headlights, blower motor, rear
window defroster) on and verify that the voltage reading increases.
Generator generated current minimum value
70 % of the nominal output current (nominal output current: 110 A)
[Ambient temp. 20 °C {68 °F}, voltage 13.0—15.0 V, both engine and
generator are hot]
Generator rotor resistance (between slip rings) [20 °C
{68 °F}]
1.8—2.2 ohm
Generator brush length
Standard: 22.5 mm {0.89 in}
Minimum: 5.0 mm {0.20 in}
Generator brush spring force
Standard: 4.1—5.3 N {0.42—0.54 kgf, 0.92—1.19 lbf}
Minimum: 1.7 N {0.17 kgf, 0.38 lbf}
Firing order
1— 3— 4— 2 (all cylinders independent firing)
Spark plug type
L3K9 18 110A, L3Y3 18 110
Spark plug gap
0.7—0.8 mm {0.028—0.031 in}
Spark plug resistance [25°C {77 °F}]
3.0—7.5 kilohms
Starter no-load test voltage
11 V
Starter no-load test current
90 A or less
Starter pinion gap
0.5—2.0 mm {0.02—0.07 in}
Starter armature runout
0.05 mm {0.002 in} max.
Starter commutator diameter
Standard: 29.4 mm {1.16 in}
Minimum: 28.8 mm {1.13 in}
Segment groove depth of starter commutator
Standard: 0.4—0.6 mm {0.016—0.023 in}
Minimum: 0.2 mm {0.008 in}
Starter brush length
Standard: 12.3 mm {0.48 in}
Minimum: 7.0 mm {0.28 in}
Starter brush spring force
Standard: 18.3—24.9 N {1.87—2.53 kgf, 4.12—5.59 lbf}
Minimum: 5.9 N {0.6 kgf, 1.3 lbf}
Item
Specification
1
2
3
4
ENGINE
CYLINDER No.
CRANKSHAFT
PULLEY
Item
U.S.A. and CANADA
Except U.S.A. and CANADA
Engine oil grade
API SL or ILSAC
Engine oil viscosity
5W-30
(ILSAC)
(ILSAC)
1871-1U-06B(01-50).fm 2 ページ 2006年3月15日 水曜日 午前10時55分
SERVICE TOOLS [L3 WITH TC]
01-60–1
01-60
2007 Mazda CX-7 Workshop Manual (1871–1U–06B)
Revised 11/2006 (Ref. No. R172/06)
01-60
SERVICE TOOLS [L3 WITH TC]
ENGINE SST[L3 WITH TC]. . . . . . . . . . . 01-60–1
End of Toc
WM: ENGINE
ENGINE SST[L3 WITH TC]
id016039800100
1: Mazda SST number
2: Global SST number
Example
1:49 UN01 052
2:310–D005
Spring lock
coupler tool
(green)
1:49 UN30 3328
2:303–328
Rear oil seal
replacer
1:–
2:303–507
Crankshaft TDC
timing peg
1:–
2:205-126
Holding tool
1:–
2:205–072–02
Crankshaft
holding tool pins
1:49 UN30
310610
2:303–1061
Camshaft
alignment
timing tool
1:49 H010 401
2:–
Oil seal installer
1:49 G013 101
2:–
Remover
1:49 C017 5A0
2: –
Engine support
set
1:49 9200 145
2:–
Radiator cap
tester adapter
set
1:49 N013 101A
2:–
Body
(Components
part of 49 N013
1A0D)
1:49 0187 280A
2:–
Oil pressure
gauge
1:49 E019 001
2:–
Adapter
1:49 E042 001
2:–
Remover
1: –
2:134-01049
Evaporative
emission
system tester
1:49 H080 740A
2: –
Pressure tester
SERVICE TOOLS [L3 WITH TC]
01-60–2
2007 Mazda CX-7 Workshop Manual (1871–1U–06B)
Revised 11/2006 (Ref. No. R172/06)
End Of Sie
1:49 L018 001
2:–
O2 sensor
wrench
1:49 N013 102A
2:–
Adapter Hose
(Components
part of 49 N013
1A0D)
1:49 B019 901B
2:–
Gauge
(Components
part of 49 N013
1A0D)
1:49 G040 001
2:–
Handle
1:49 G040 002
2:–
Installer
—
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст