Mazda CX 7. Manual — part 410
INTERIOR TRIM
09-17–7
09-17
3. Assemble in the reverse order of disassembly.
.
End Of Sie
4
3
1
2
2
5
6
acxuuw00000650
1
Dashboard wiring harness
2
Demister duct
3
Upper garnish
4
Dashboard center panel
5
Dashboard member
6
Dashboard
INTERIOR TRIM
09-17–8
COLUMN COVER REMOVAL/INSTALLATION
id091700800800
1. Remove the screws.
2. Pull the upper column cover upward and detach
the upper column cover from the lower column
cover.
3. Remove the lower column cover.
4. Remove the ignition key illumination.
5. Install in the reverse order of removal.
Note
• The upper column cover is integrated with
the meter hood.
End Of Sie
GLOVE COMPARTMENT REMOVAL/INSTALLATION
id091700800700
1. Press the stay damper in the direction shown by
the arrow and detach it from the glove
compartment lid.
2. Bend the stoppers inward to remove.
3. Turn the glove compartment downward and pull
the pins.
4. Remove the glove compartment.
5. Install in the reverse order of removal.
End Of Sie
CENTER PANEL REMOVAL/INSTALLATION
id091700804500
1. Remove the following parts:
(1) Front scuff plate inner (See 09-17-19 FRONT SCUFF PLATE REMOVAL/INSTALLATION.)
(2) Front side trim (See 09-17-18 FRONT SIDE TRIM REMOVAL/INSTALLATION.)
(3) Console panel (See 09-17-15 CONSOLE PANEL REMOVAL/INSTALLATION.)
(4) Console (See 09-17-13 CONSOLE REMOVAL/INSTALLATION.)
(5) Hood release lever (See 09-14-25 HOOD LATCH AND RELEASE LEVER REMOVAL/INSTALLATION.)
(6) Lower panel (See 09-17-9 LOWER PANEL REMOVAL/INSTALLATION.)
2. Insert a tape-wrapped flathead screwdriver into
the service hole and slide it in the direction of
arrow (1).
3. After sliding the flathead screwdriver, insert it in
the direction of arrow (2) and remove clip A.
Caution
• Insert a flathead screwdriver until clip A
can be removed while being careful not
to allow the climate control unit to be
damaged.
4. Remove clip A on the opposite side in the same
procedure.
IGNITION KEY
ILLUMINATION
LOWER COLUMN
COVER
SCREW
acxuuw00000652
PIN
PIN
GLOVE
COMPARTMENT
STAY DAMPER
STOPPER
acxuuw00000665
(2)
(1)
A
A
A
CLIP A
CENTER PANEL
FLATHEAD SCREWDRIVER
SERVICE HOLE
CENTER PANEL
acxuuw00002318
INTERIOR TRIM
09-17–9
09-17
5. Insert a tape-wrapped flathead screwdriver into
the service hole and lift up the center panel with
clips B pressed in, then remove clips B.
6. Pull the center panel outward and detach clips C.
7. Remove the center panel.
8. Install in the reverse order of removal.
End Of Sie
LOWER PANEL REMOVAL/INSTALLATION
id091700801100
Driver’s Side
1. Remove the following parts:
(1) Front scuff plate inner (driver’s side) (See 09-17-19 FRONT SCUFF PLATE REMOVAL/INSTALLATION.)
(2) Front side trim (driver’s side) (See 09-17-18 FRONT SIDE TRIM REMOVAL/INSTALLATION.)
(3) Console panel (See 09-17-15 CONSOLE PANEL REMOVAL/INSTALLATION.)
(4) Console (See 09-17-13 CONSOLE REMOVAL/INSTALLATION.)
(5) Hood release lever (See 09-14-25 HOOD LATCH AND RELEASE LEVER REMOVAL/INSTALLATION.)
2. Remove the screws.
3. Pull the lower panel outward and detach clips A.
4. Remove the passenger compartment
temperature sensor. (See 07-40-23 PASSENGER
COMPARTMENT TEMPERATURE SENSOR
REMOVAL/INSTALLATION.)
5. Disconnect the headlight leveling switch
connector and TCS OFF switch connector.
6. Remove the lower panel.
7. Install in the reverse order of removal.
C
C
C
B
B
C
C
C
C
CLIP C
CENTER PANEL
CLIP B
FLATHEAD
SCREWDRIVER
CENTER PANEL
SERVICE HOLE
acxuuw00000877
CLIP A
SCREW
A
A
A
A
A
A
A
A
A
acxuuw00000872
INTERIOR TRIM
09-17–10
Passenger’s Side
1. Remove the following parts:
(1) Front scuff plate inner (passenger’s side) (See 09-17-19 FRONT SCUFF PLATE REMOVAL/
INSTALLATION.)
(2) Front side trim (passenger’s side) (See 09-17-18 FRONT SIDE TRIM REMOVAL/INSTALLATION.)
(3) Console panel (See 09-17-15 CONSOLE PANEL REMOVAL/INSTALLATION.)
(4) Console (See 09-17-13 CONSOLE REMOVAL/INSTALLATION.)
(5) Glove compartment (See 09-17-8 GLOVE COMPARTMENT REMOVAL/INSTALLATION.)
2. Remove the screws.
3. Pull the lower panel outward and detach clips A.
4. Remove the lower panel.
5. Install in the reverse order of removal.
End Of Sie
METER HOOD REMOVAL/INSTALLATION
id091700800900
1. Remove the following parts:
(1) Front scuff plate inner (driver’s side) (See 09-17-19 FRONT SCUFF PLATE REMOVAL/INSTALLATION.)
(2) Front side trim (driver’s side) (See 09-17-18 FRONT SIDE TRIM REMOVAL/INSTALLATION.)
(3) Console panel (See 09-17-15 CONSOLE PANEL REMOVAL/INSTALLATION.)
(4) Console (See 09-17-13 CONSOLE REMOVAL/INSTALLATION.)
(5) Hood release lever (See 09-14-25 HOOD LATCH AND RELEASE LEVER REMOVAL/INSTALLATION.)
(6) Lower panel (See 09-17-9 LOWER PANEL REMOVAL/INSTALLATION.)
2. Pull the upper column cover upward and detach
the upper column cover from the lower column
cover.
3. Pull the meter hood and remove clips A and tabs
B.
4. Remove the meter hood.
5. Install in the reverse order of removal.
End Of Sie
VENTILATOR GRILLE REMOVAL/INSTALLATION
id091700804600
Warning
• Handling the air bag module improperly can accidentally operate (deploy) the air bag module,
which may seriously injure you. Read the service warnings and cautions before handling the air
bag module. (See 08-10-3 AIR BAG SYSTEM SERVICE WARNINGS.) (See 08-10-5 AIR BAG SYSTEM
SERVICE CAUTIONS.)
Driver’s Side
1. Remove the following parts:
(1) A-pillar lower trim (driver’s side) (See 09-17-16 A-PILLAR LOWER TRIM REMOVAL/INSTALLATION.)
(2) A-pillar trim (driver’s side) (See 09-17-15 A-PILLAR TRIM REMOVAL/INSTALLATION.)
(3) Front scuff plate inner (See 09-17-19 FRONT SCUFF PLATE REMOVAL/INSTALLATION.)
(4) Front side trim (See 09-17-18 FRONT SIDE TRIM REMOVAL/INSTALLATION.)
(5) Console panel (See 09-17-15 CONSOLE PANEL REMOVAL/INSTALLATION.)
(6) Console (See 09-17-13 CONSOLE REMOVAL/INSTALLATION.)
(7) Hood release lever (See 09-14-25 HOOD LATCH AND RELEASE LEVER REMOVAL/INSTALLATION.)
(8) Lower panel (See 09-17-9 LOWER PANEL REMOVAL/INSTALLATION.)
(9) Meter hood (See 09-17-10 METER HOOD REMOVAL/INSTALLATION.)
(10)Instrument cluster (See 09-22-2 INSTRUMENT CLUSTER REMOVAL/INSTALLATION.)
(11)Center panel (See 09-17-8 CENTER PANEL REMOVAL/INSTALLATION.)
(12)Dash board garnish (See 09-17-18 DASHBOARD GARNISH REMOVAL/INSTALLATION.)
CLIP A
SCREW
A
A
A
A
A
acxuuw00000873
A
A
B
A
B
A
A
A
CLIP A
METER HOOD
TAB B
UPPER COLUMN
COVER
acxuuw00000659
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст