Mazda CX 7. Manual — part 208
CONVENTIONAL BRAKE SYSTEM
04-11–3
04-11
AIR BLEEDING
id041100800200
Caution
• Brake fluid will damage painted surfaces. Be careful not to spill any on painted surfaces. If it is
spilled, wipe it off immediately.
Note
• Keep the fluid level in the reserve tank at 3/4 full or more during the air bleeding.
• Begin air bleeding with the brake caliper that is furthest from the master cylinder.
Brake fluid type
SAE J1703, FMVSS 116 DOT-3
1. Remove the bleeder cap on the brake caliper, and attach a vinyl tube to the bleeder screw.
2. Place the other end of the vinyl tube in a clear container and fill the container with fluid during air bleeding.
3. Working with two people, one should pump the brake pedal several times and depress and hold the pedal
down.
4. While the brake pedal is depressed, the other
should loosen the bleeder screw using the SST,
drain out any fluid containing air bubbles, and
tighten the bleeder screw.
Tightening torque
Front: 5.9— 9.8 N·m {61— 99 kgf·cm, 53— 86
in·lbf}
Rear: 6.9— 9.8 N·m {71— 99 kgf·cm, 61— 86
in·lbf}
5. Repeat Steps 3 and 4 until no air bubbles are
seen.
6. Perform air bleeding as described in the above
procedures for all brake calipers.
7. After air bleeding, inspect the following:
• Brake operation
• Fluid leakage
• Fluid level
End Of Sie
WM: VACUUM LINE
VACUUM LINE INSPECTION
id041100801500
1. Remove the vacuum hose. (See 04-11-4 VACUUM HOSE REMOVAL/INSTALLATION.)
2. Verify that air can be blown from the power brake
unit side of the vacuum hose towards the engine
side, and that air cannot be blown in the opposite
direction.
• If there is any malfunction of the inner check
valve, replace it together with the vacuum
hose as a single unit.
End Of Sie
49 0259 770B
acxuuw00001068
CHECK VALVE
TO INTAKE MANIFOLD
acxuuw00001745
1871-1U-06B(04-11).fm 3 ページ 2006年3月15日 水曜日 午前11時13分
CONVENTIONAL BRAKE SYSTEM
04-11–4
VACUUM HOSE REMOVAL/INSTALLATION
id041100801600
1. Remove the clamps and vacuum hose (power brake unit side).
2. Insert a thin flathead screwdriver at the point
indicated by the arrow in the figure, push the ring
down and disconnect the vacuum hose from the
intake manifold.
3. Remove the vacuum hose.
4. Install in the reverse order of removal.
5. Verify that the vacuum hose is inserted so that the
joint contacts the intake manifold ring.
End Of Sie
WM: BRAKE PEDAL
BRAKE PEDAL INSPECTION
id041100801100
Pedal Height Inspection
1. Measure the distance from the center of the
upper surface of the pedal pad to the insulator
and verify that it is as specified.
• If not within the specification, inspect the
following items and repair or replace the
applicable part if there is any malfunction.
— Power brake unit installation condition
— Deformation of or damage to the power
brake unit fork
— Brake pedal installation condition
— Clevis pin wear
• If there is no malfunction in the above items,
replace the brake pedal.
Brake pedal height (reference value)
204.3 mm {8.043 in}
JOINT
RING
INTAKE MANIFOLD
POWER BRAKE UNIT
acxuuw00001109
JOINT
RING
INTAKE MANIFOLD
POWER BRAKE UNIT
acxuuw00001110
PEDAL HEIGHT
INSULATOR
acxuuw00001740
1871-1U-06B(04-11).fm 4 ページ 2006年3月15日 水曜日 午前11時13分
CONVENTIONAL BRAKE SYSTEM
04-11–5
04-11
Pedal Play Inspection
1. Pump the pedal several times to release the vacuum in the power brake unit.
2. Gently depress the pedal by hand and measure the pedal play.
• If not within the specification, inspect the wear of the clevis pin. Replace it if there is any malfunction.
Brake pedal play
2— 5 mm {0.08— 0.19 in}
Note
• If there is no malfunction in the clevis pin, there is a possibility that the power brake unit has some
malfunction. Verify that there are no malfunctions, and replace it if necessary.
Pedal-to-floor Clearance Inspection
1. Start the engine and depress the brake pedal with a force of 147 N {15.0 kgf, 33.0 lbf}.
2. Measure the distance from the center of the
upper surface of the pedal pad to the floor
covering and verify that it is as specified.
• If it is less than the specification, inspect for
air in the brake line.
Brake pedal-to-floor clearance (Brake pedal
when depressed at 147 N {15.0 kgf, 33.0
lbf})
99.1 mm {3.91 in} or more
End Of Sie
PEDAL-TO-FLOOR
CLEARANCE
FLOOR
COVERING
acxuuw00001741
1871-1U-06B(04-11).fm 5 ページ 2006年3月15日 水曜日 午前11時13分
CONVENTIONAL BRAKE SYSTEM
04-11–6
BRAKE PEDAL REMOVAL/INSTALLATION
id041100801200
Caution
• The clearance between the brake switch and the brake pedal is automatically adjusted to the
correct amount when the brake switch is inserted into the installation hole on the brake pedal and
rotated to fix in place. If the brake switch is not properly installed, the clearance may be incorrect,
causing a brake light malfunction. Therefore, always verify that the brake pedal is properly
installed and fully released before installing the brake switch to the pedal.
• Once the brake switch clearance has automatically been adjusted, it cannot be adjusted again.
Therefore, replace the switch with a new one when replacing the power brake unit or the pedal, or
performing any procedure that changes the pedal stroke.
1. Remove the battery and battery tray. (See 01-17-2 BATTERY REMOVAL/INSTALLATION[L3 WITH TC].)
2. Remove the battery tray bracket as shown in the
figure.
3. Disconnect the brake fluid level sensor connector.
4. Remove the master cylinder reserve tank bracket
installation nuts. (See 04-11-10 MASTER
CYLINDER REMOVAL/INSTALLATION.)
5. Remove the accelerator pedal. (See 01-13-17
ACCELERATOR PEDAL REMOVAL/
INSTALLATION[L3 WITH TC].)
6. Remove in the order indicated in the table.
7. Install in the reverse order of removal.
.
BATTERY TRAY BRACKET
18—26 N·m
{1.9—2.6 kgf·m,
14—19 ft·lbf}
acxuuw00001908
5
B
B
7
7
2
1
3
9
6
8
A
A
C
C
4
18.6—25.5
{1.90—2.60,
13.8—18.8}
18.6—25.5
{1.90—2.60,
13.8—18.8}
R
N·m {kgf·m, ft·lbf}
acxuuw00001743
1
Brake switch connector
(See 04-11-8 Brake Switch Connector Installation
Note.)
2
Brake switch
(See 04-11-8 Brake Switch Installation Note.)
3
Interlock cable
(See 05-18-2 INTERLOCK CABLE ADJUSTMENT.)
4
Noise filter
5
Snap pin
6
Clevis pin
1871-1U-06B(04-11).fm 6 ページ 2006年3月15日 水曜日 午前11時13分
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст