Mazda CX 7. Manual — part 419
LIGHTING SYSTEMS
09-18–11
09-18
FRONT FOG LIGHT BULB REMOVAL/INSTALLATION
id091800802300
1. Disconnect the negative battery cable.
2. Slightly bend back the mudguard.
3. Disconnect the front fog light bulb connector and
remove the front fog light bulb by turning it in the
direction of the arrow.
Caution
• A halogen bulb generates extremely high
heat when it is illuminated. If the surface
of the bulb is soiled, excessive heat will
build up and the life of the bulb will be
shortened. When handling the bulb, hold
the flange, not the glass.
4. Install in the reverse order of removal.
End Of Sie
WM: REAR COMBINATION LIGHT
REAR COMBINATION LIGHT REMOVAL/INSTALLATION
id091800801000
1. Disconnect the negative battery cable.
2. Remove the service hole cover.
3. Remove in the order indicated in the table.
.
4. Install in the reverse order of removal.
End Of Sie
CONNECTOR
FRONT FOG
LIGHT BULB
LH
RH
FRONT FOG LIGHT BULB
acxuuw00001720
1
Connector
2
Nut
3
Rear combination light
acxuuw00001722
3
1
2
4.1—6.1 N·m
{42—62 kgf·cm, 37—53 in·lbf}
acxuuw00001723
LIGHTING SYSTEMS
09-18–12
REAR COMBINATION LIGHT BULB REMOVAL/INSTALLATION
id091800805900
1. Disconnect the negative battery cable.
2. Remove the service hole cover.
3. Remove in the order indicated in the table.
.
4. Install in the reverse order of removal.
End Of Sie
WM: HIGH-MOUNT BRAKE LIGHT
HIGH-MOUNT BRAKE LIGHT REMOVAL/INSTALLATION
id091800802000
1. Disconnect the negative battery cable.
2. Remove the cover in the interior of the liftgate.
3. Remove in the order indicated in the table.
.
4. Install in the reverse order of removal.
End Of Sie
WM: LICENSE PLATE LIGHT
LICENSE PLATE LIGHT REMOVAL/INSTALLATION
id091800801100
1. Disconnect the negative battery cable.
2. Remove the rear finisher.(See09-16-3 REAR FINISHER REMOVAL/INSTALLATION.)
3. Remove in the order indicated in the table.
.
4. Install in the reverse order of removal.
End Of Sie
WM: COMBINATION SWITCH
1
Connector
2
Socket
3
Rear side marker light bulb
4
Back-up light bulb
5
Rear turn light bulb
6
Brake light/taillight bulb
acxuuw00001722
1
1
2
2
5
4
3
6
acxuuw00001724
1
Connector
2
High-mount brake light
2
1
TAB
TAB
acxuuw00001726
1
Connector
2
License plate light
3
Lens
4
License plate light bulb
HOOK
4
3
1
2
acxuuw00001727
LIGHTING SYSTEMS
09-18–13
09-18
COMBINATION SWITCH REMOVAL/INSTALLATION
id091800802500
Warning
• If the negative battery cable or the steering angle sensor connector is disconnected, the stored
initial position of the steering angle sensor will be cleared and the DSC will not operate properly,
making the vehicle unsafe to drive. Perform the steering angle sensor initialization procedure after
connecting the negative battery cable.
1. Disconnect the negative battery cable.
2. Remove the following parts:
(1) Driver-side air bag module (See 08-10-6 DRIVER-SIDE AIR BAG MODULE REMOVAL/INSTALLATION.)
(2) Steering wheel (See 06-14-6 STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION.)
(3) Column cover (See 09-17-8 COLUMN COVER REMOVAL/INSTALLATION.)
3. Remove in the order indicated in the table.
.
4. Disconnect the steering angle sensor connector.
5. Install in the reverse order of removal.
6. Perform the steering angle sensor reference point
setting. (See 09-40-8 STEERING ANGLE
SENSOR INITIALIZATION PROCEDURE.)
End Of Sie
COMBINATION SWITCH DISASSEMBLY/ASSEMBLY
id091800802600
Caution
• If the disc on the combination switch is deformed or has foreign material adhering to it,
performance of the steering angle sensor may be reduced, causing abnormal operation. When
handling the combination switch, be careful not to deform the disc and make sure there is no
foreign material on it.
1. Disassemble in the order indicated in the table.
.
2. Assemble in the reverse order of disassembly.
End Of Sie
WM: LIGHT SWITCH
LIGHT SWITCH REMOVAL/INSTALLATION
id091800802800
1. Disconnect the negative battery cable.
2. Remove the column cover. (See 09-17-8 COLUMN COVER REMOVAL/INSTALLATION.)
3. Disconnect the light switch connector.
4. Remove the screws, then remove the light switch.
5. Install in the reverse order of removal.
End Of Sie
1
Connector
2
Screw
3
Combination switch
3
1
2
2
ampjjw00002214
1
Screw
2
Wiper and washer switch
3
Light switch
4
Body
4
3
1
2
1
acxuuw00001728
CONNECTOR
SCREW
LIGHT SWITCH
acxuuw00001729
LIGHTING SYSTEMS
09-18–14
LIGHT SWITCH INSPECTION
id091800802900
1. Verify that the continuity between the light switch terminals is as indicated in the table.
• If not as indicated in the table, replace the light switch.
Headlight switch (Vehicle without auto light)
Headlight switch (Vehicle with auto light)
Turn Switch
End Of Sie
WM: FRONT FOG LIGHT SWITCH
O
Q
C
E
A
P
L
J
F
D
*
*
*
*
*
*
*
L
P
J
Q
O
R
HI
FLASH-
TO-PASS
HEAD-
LIGHT
OFF
TNS
LO
acxuuw00001730
: Continuity
Switch position
Light
Dimmer
Flash-
to-pass
OFF
Off
On
Off
On
Off
On
-
-
-
TNS
LO
HI
Head-
light
Terminal
J
L
P
O
Q
R
acxuuw00001731
O
Q
C
E
A
P
L
J
F
H
D
*
*
*
*
*
*
L
P
J
H
Q
O
R
HI
FLASH-
TO-PASS
HEAD-
LIGHT
AUTO
OFF
TNS
LO
acxuuw00001732
: Continuity
Switch position
Light
Dimmer
Flash-
to-pass
OFF
Off
On
Off
On
Off
On
-
-
-
TNS
LO
HI
Head-
light
Off
On
-
LO
HI
Auto
Terminal
J
L
P
O
Q
R
H
acxuuw00001733
C
LEFT
RIGHT
E
A
O
Q
C
E
A
P
L
J
F
H
D
*
*
*
*
*
*
acxuuw00001734
: Continuity
Switch position
Left
Off
Right
Terminal
A
C
E
acxuuw00001735
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст