Mazda CX 7. Manual — part 420
LIGHTING SYSTEMS
09-18–15
09-18
FRONT FOG LIGHT SWITCH INSPECTION
id091800803200
1. Verify that the continuity between the front fog
light switch terminals is as indicated in the table.
• If not as indicated in the table, replace the
light switch.
End Of Sie
WM: HAZARD WARNING SWITCH
HAZARD WARNING SWITCH REMOVAL/INSTALLATION
id091800803000
1. Disconnect the negative battery cable.
2. Remove the following parts:
(1) Front scuff plate inner (See 09-17-19 FRONT SCUFF PLATE REMOVAL/INSTALLATION.)
(2) Front side trim (See 09-17-18 FRONT SIDE TRIM REMOVAL/INSTALLATION.)
(3) Console panel (See 09-17-15 CONSOLE PANEL REMOVAL/INSTALLATION.)
(4) Console (See 09-17-13 CONSOLE REMOVAL/INSTALLATION.)
(5) Hood release lever (See 09-14-25 HOOD LATCH AND RELEASE LEVER REMOVAL/INSTALLATION.)
(6) Lower panel (See 09-17-9 LOWER PANEL REMOVAL/INSTALLATION.)
(7) Center panel (See 09-17-8 CENTER PANEL REMOVAL/INSTALLATION.)
3. Remove in the order indicated in the table.
.
4. Install in the reverse order of removal.
End Of Sie
HAZARD WARNING SWITCH INSPECTION
id091800803100
1. Verify that the continuity between the hazard
warning switch terminals is as indicated in the
table.
• If not as indicated in the table, replace the
hazard warning switch.
End Of Sie
WM: HEADLIGHT LEVELING SWITCH
P
D
OFF
ON
O
Q
C
E
A
P
L
J
F
H
D
*
*
*
*
*
*
acxuuw00001736
D
P
:
Continuity
Switch position
Terminal
Light
Front fog
light switch
OFF
OFF
ON
ON
ON
ON
TNS
Head light
Auto
acxuuw00001737
1
Hazard warning switch panel
2
Screw
3
Hazard warning switch
3
1
2
acxuuw00002276
C
B
A
D
A
C
B
D
acxuuw00001748
C
A
B
D
: Continuity
: Bulb
Switch position
Terminal
Off
On
acxuuw00001749
LIGHTING SYSTEMS
09-18–16
HEADLIGHT LEVELING SWITCH REMOVAL/INSTALLATION
id091800803600
1. Disconnect the negative battery cable.
2. Remove in the order indicated in the table.
3. Install in the reverse order of removal.
Switch Bezel Component Removal Note
1. Access the switch bezel component from behind of the dashboard, and squeeze the tabs of the switch bezel
component.
2. Remove the switch bezel component from the dashboard.
End Of Sie
HEADLIGHT LEVELING SWITCH INSPECTION
id091800803700
1. Verify that continuity between the headlight
leveling switch terminals is as indicated in the
table.
• If not as indicated in the table, replace the
headlight leveling switch.
End Of Sie
WM: AUTO LIGHT SYSTEM
1
Switch bezel component
(See 09-18-16 Switch Bezel Component Removal
Note.)
2
Connector
3
Headlight leveling switch
TAB
3
1
2
acxuuw00001750
0
1
R
1
R
2
R
3
R
4
R
5
2
3
B
H
D
F
J
B
D
F
H
J
*
*
*
*
*
acxuuw00001751
R
1
R
2
R
3
R
4
R
5
R
1
R
2
R
3
R
4
R
5
R
1
R
2
R
3
R
4
R
5
R
1
R
2
R
3
R
4
R
5
B
0
1
2
3
H
D
J
F
R
1
: 715 ohms R
2
: 715 ohms R
3
: 261 ohms
R
4
: 604 ohms R
5
: 715 ohms
Switch
position
Terminal
: Resistance
: Bulb
acxuuw00001752
LIGHTING SYSTEMS
09-18–17
09-18
DRL AND AUTO LIGHT SYSTEM WIRING DIAGRAM
id091800807100
With DRL
B+
B+
B+
B+
B+
2M
2C
2G
2J
2N
2K
2L
1G
1D
1K
1H
1A
2P
2I
2O
2H
2B
2A
AUTO
TNS
OFF
OFF
HEAD
PASS
FRONT
FOG
DIMMER
SWITCH
LIGHT SWITCH
AUTO LIGHT
SENSOR
TNS
RELAY
TNS
HEADLIGHT
RELAY
HEAD LIGHT
(LOW-BEAM)
FRONT
FOG
LIGHT
IG1
IG
BRAKE
LAMP
PARKING
BRAKE
SWITCH
HEADLIGHT RH
(HIGH-BEAM)
HEADLIGHT LH
(HIGH-BEAM)
AUTO LIGHT CONTROL
MODULE
HI
LO
FRONT FOG
LIGHT RELAY
HIGH-BEAM
INDICATOR
LIGHT
acxuun00000698
LIGHTING SYSTEMS
09-18–18
Without DRL
End Of Sie
B+
B+
B+
B+
TNS
RELAY
IG
2M
2C
2G
2N
2I
2O
2H
2B
2A
AUTO
TNS
OFF
OFF
HEAD
PASS
HI LO
FRONT
FOG
DIMMER
SWITCH
LIGHT SWITCH
AUTO LIGHT
SENSOR
FRONT FOG
LIGHT RELAY
FUSE
MAIN
HEADLIGHT
(HIGH-BEAM)
HIGH-BEAM
INDICATOR
LIGHT
HEADLIGHT
RELAY
HEADLIGHT
(LOW-BEAM)
TNS
AUTO LIGHT CONTROL
MODULE
acxuuw00001847
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст