Mazda CX 7. Manual — part 379
GLASS/WINDOWS/MIRRORS
09-12–3
09-12
End Of Sie
WM: DOOR GLASS
FRONT DOOR GLASS REMOVAL/INSTALLATION
id091200800400
1. Adjust the door glass position as shown in the
figure.
2. Disconnect the negative battery cable.
3. Remove the inner garnish. (See 09-17-20 INNER
GARNISH REMOVAL/INSTALLATION.)
4. Remove the front door trim. (See 09-17-20
FRONT DOOR TRIM REMOVAL/
INSTALLATION.)
5. Remove the front door speaker. (See 09-20-6
FRONT DOOR SPEAKER REMOVAL/
INSTALLATION.)
6. Remove the hole cover.
7. Remove the bolts. (See 09-12-4 Front door glass
removal note.)
8. Lift the front door glass up and remove it in the
direction of the arrow.
9. Install in the reverse order of removal.
Note
• When installing the front door glass, align
the glass edge with the glass run channel by
hand through the speaker installation hole.
9
Front power window regulator
(See 09-12-5 FRONT POWER WINDOW
REGULATOR REMOVAL/INSTALLATION.)
10 Rear power window regulator
(See 09-12-6 REAR POWER WINDOW REGULATOR
REMOVAL/INSTALLATION.)
11 Rear window glass
(See 09-12-20 REAR WINDOW GLASS REMOVAL.)
(See 09-12-21 REAR WINDOW GLASS
INSTALLATION.)
(See 09-12-31 FILAMENT INSPECTION.)
(See 09-12-31 FILAMENT REPAIR.)
12 Power window subswitch
(See 09-12-11 POWER WINDOW SUBSWITCH
REMOVAL/INSTALLATION.)
(See 09-12-11 POWER WINDOW SUBSWITCH
INSPECTION.)
13 Power outer mirror switch
(See 09-12-34 POWER OUTER MIRROR SWITCH
REMOVAL/INSTALLATION.)
(See 09-12-35 POWER OUTER MIRROR SWITCH
INSPECTION.)
14 Power window main switch
(See 09-12-8 POWER WINDOW MAIN SWITCH
REMOVAL/INSTALLATION.)
(See 09-12-8 POWER WINDOW MAIN SWITCH
INSPECTION.)
(See 09-12-13 POWER WINDOW INITIALIZATION
PROCEDURE.)
(See 09-12-14 TWO-STEP DOWN FUNCTION
OPERATIVE/NON-OPERATIVE SWITCHING
PROCEDURE.)
(See 09-12-15 DOOR GLASS POSITION CHANGE
PROCEDURE.)
70 mm
{2.8 in}
acxuuw00001473
FRONT DOOR
GLASS
HOLE COVER
BOLT
4.5—6.5 N·m
{46 —66 kgf·cm,
40—57 in·lbf}
acxuuw00001474
GLASS/WINDOWS/MIRRORS
09-12–4
Front door glass removal note
1. When remove the front door glass, align the glass
edge with the glass run channel by hand through
the speaker installation hole.
End Of Sie
REAR DOOR GLASS REMOVAL/INSTALLATION
id091200800500
1. Fully lower the rear door glass.
2. Remove the rear beltline molding. (See 09-16-9 REAR BELTLINE MOLDING REMOVAL/INSTALLATION.)
3. Remove the sail garnish. (See 09-17-12 SAIL GARNISH REMOVAL/INSTALLATION.)
4. Remove the rear door garnish. (See 09-16-3 REAR DOOR GARNISH REMOVAL/INSTALLATION.)
5. Adjust the door glass position as shown in the
figure.
6. Disconnect the negative battery cable.
7. Remove the rear door trim. (See 09-17-23 REAR
DOOR TRIM REMOVAL/INSTALLATION.)
8. Remove the bolts .
acxuuw00001672
140 mm {5.5in}
acxuuw00001481
BOLT
6.9—9.8 N·m
{71—99 kgf·cm,
62—86 in·lbf}
acxuuw00001482
GLASS/WINDOWS/MIRRORS
09-12–5
09-12
9. Remove the rear door glass guide and glass run
channel as a single unit.
10. Remove the hole cover.
11. Remove the bolt
12. Lift the rear door glass up and remove it in the
direction of the arrow.
13. Install in the reverse order of removal.
End Of Sie
WM: WINDOW REGULATOR
FRONT POWER WINDOW REGULATOR REMOVAL/INSTALLATION
id091200800200
1. Disconnect the negative battery cable.
2. Remove the following parts:
(1) Inner garnish (See 09-17-20 INNER GARNISH REMOVAL/INSTALLATION.)
(2) Front door trim (See 09-17-20 FRONT DOOR TRIM REMOVAL/INSTALLATION.)
(3) Front door speaker. (See 09-20-6 FRONT DOOR SPEAKER REMOVAL/INSTALLATION.)
(4) Front door glass (See 09-12-3 FRONT DOOR GLASS REMOVAL/INSTALLATION.)
(5) Power window motor (See 09-12-7 POWER WINDOW MOTOR REMOVAL/INSTALLATION.)
(6) Front beltline molding (See 09-16-9 FRONT BELTLINE MOLDING REMOVAL/INSTALLATION.)
3. Remove the nuts .
REAR DOOR
GLASS GUIDE
GLASS RUN CHANNEL
acxuuw00001483
HOLE COVER
BOLT
4.5—6.5 N·m {46—66 kgf·cm,
40—57 in·lbf}
acxuuw00001484
NUT
6.7—9.8 N·m
{69—99 kgf·cm,
60—86 in·lbf}
acxuuw00001466
GLASS/WINDOWS/MIRRORS
09-12–6
4. Insert a hand through the speaker installation
hole, rotate the drum housing in the direction
shown in the figure to detach the tabs from the
front door unit.
5. Remove the front power window regulator as
shown in the figure.
6. Install in the reverse order of removal.
Caution
• Make sure the cable does not unspool
from the drum housing when installing.
End Of Sie
REAR POWER WINDOW REGULATOR REMOVAL/INSTALLATION
id091200800300
1. Disconnect the negative battery cable.
2. Remove the sail garnish. (See 09-17-12 SAIL GARNISH REMOVAL/INSTALLATION.)
3. Remove the rear door garnish. (See 09-16-3 REAR DOOR GARNISH REMOVAL/INSTALLATION.)
4. Remove the rear door trim. (See 09-17-23 REAR DOOR TRIM REMOVAL/INSTALLATION.)
5. Remove the rear door speaker. (See 09-20-7 REAR DOOR SPEAKER REMOVAL/INSTALLATION.)
6. Remove the rear door glass. (See 09-12-4 REAR DOOR GLASS REMOVAL/INSTALLATION.)
7. Remove the power window motor. (See 09-12-7 POWER WINDOW MOTOR REMOVAL/INSTALLATION.)
8. Remove the nuts.
9. Insert a hand through the speaker installation
hole, rotate the drum housing in the direction
shown in the figure to detach the tabs from the
rear door unit.
TAB
DRUM HOUSING
acxuuw00001467
FRONT POWER WINDOW
REGULATOR
acxuuw00001468
NUT
6.7—9.8 N·m
{69—99 kgf·cm,
60—86 in·lbf}
acxuuw00001900
TAB
DRUM HOUSING
acxuuw00001470
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст