Mazda CX-9 Grand Touring. Manual — part 93
TCM REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL]
1. Disconnect the negative battery cable.
2. Remove the air cleaner component. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION
[MZI-3.7] .)
3. Disconnect the TCM connector.
4. Remove the clip and disconnect the selector cable.
B20
Vehicle
speed (+)
VSS
B19 and B20 (wiring
harness-side).
[AW6A-EL,
AW6AX-EL]
Inspect relate
harness
B21
Shift
solenoid F
control
Shift
solenoid F
Inspect
resistance
between
couple
component
terminals
B21 and
B16
(wiring
harness-
side).
ATF
temperature:
20°C {68°
F}
5.0-5.6 (ohms)
Inspect shift
solenoid F (Se
SOLENOID
VALVE
INSPECTIO
[AW6A-EL,
AW6AX-EL]
Inspect relate
harness
B22
Shift
solenoid E
control
GND
Shift
solenoid E
Inspect
resistance
between
couple
component
terminals
B14 and
B22
(wiring
harness-
side).
ATF
temperature:
20°C {68°
F}
5.0-5.6 (ohms)
Inspect shift
solenoid E (S
SOLENOID
VALVE
INSPECTIO
[AW6A-EL,
AW6AX-EL]
Inspect relate
harness
CAUTION:
Water or foreign material entering the connector can cause a poor
connection or corrosion. Be sure not to allow water or foreign
material on the connector when disconnecting.
CAUTION:
Do not use an impact wrench. Hold the manual shaft lever when
removing the manual shaft nut, or the transaxle may be
damaged.
2008 Mazda CX-9 Grand Touring
2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:29:30 AM
Page 41
© 2005 Mitchell Repair Information Company, LLC.
5. Set the adjustable wrench as shown in the figure to hold the manual shaft lever.
Fig. 41: Identifying Manual Shaft Lever
Courtesy of MAZDA MOTORS CORP.
6. Remove the manual shaft nut and washer.
Fig. 42: Identifying Manual Shaft Nut & Washer
Courtesy of MAZDA MOTORS CORP.
7. Remove the TCM.
Fig. 40: Identifying Manual Shaft Lever & TCM Connector
Courtesy of MAZDA MOTORS CORP.
2008 Mazda CX-9 Grand Touring
2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:29:30 AM
Page 42
© 2005 Mitchell Repair Information Company, LLC.
Fig. 43: Identifying TCM
Courtesy of MAZDA MOTORS CORP.
8. Inspect the condition of the connector pin of the coupler component (foreign material, bent pins, broken
pins) and O-ring after the TCM is removed.
Fig. 45: Identifying Connector Pin Of Coupler Component
Courtesy of MAZDA MOTORS CORP.
CAUTION:
Do not touch the terminals.
Fig. 44: Identifying Air Filter
Courtesy of MAZDA MOTORS CORP.
2008 Mazda CX-9 Grand Touring
2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:29:31 AM
Page 43
© 2005 Mitchell Repair Information Company, LLC.
9. Align the transaxle case and coupler component connector.
Fig. 46: Locating Transaxle Case
Courtesy of MAZDA MOTORS CORP.
10. Be sure to match the position of the TCM marking.
11. Install the TCM.
Fig. 47: Identifying TCM
Courtesy of MAZDA MOTORS CORP.
12. Verify the correct positioning of the TCM and coupler component.
13. Tighten the TCM mounting bolts.
Tightening torque
19.6-29.4 N.m {2.0-2.9 kgf.m, 14.5-21.6 ft.lbf}
CAUTION:
Do not turn more than 60° from the marking.
CAUTION:
Do not use an impact wrench. Hold the manual shaft lever when
2008 Mazda CX-9 Grand Touring
2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:29:31 AM
Page 44
© 2005 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст