Mazda CX-9 Grand Touring. Manual — part 91
Fig. 35: Identifying Coupler Component Connector Terminal
Courtesy of MAZDA MOTORS CORP.
Solenoid valve resistance (ATF temperature: 20°C {68°F})
SOLENOID VALVE RESISTANCE REFERENCE
5. Install the TCM. (See TCM REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL].)
6. Install the air cleaner component. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZI-
3.7] .)
7. Connect the negative battery cable.
CONTINUITY INSPECTION (ON-VEHICLE INSPECTION)
1. Disconnect the negative battery cable.
Terminal
Solenoid valve
Resistance (ohm)
B5-GND
Shift solenoid A
11-15
B2-GND
Shift solenoid B
11-15
B11-B10
Shift solenoid C
5.0-5.6
B17-B18
Shift solenoid D
5.0-5.6
B14-B22
Shift solenoid E
5.0-5.6
B21-B16
Shift solenoid F
5.0-5.6
B9-B4
TCC control solenoid
5.0-5.6
B3-B1 Line pressure control solenoid
5.0-5.6
CAUTION:
Water or foreign material entering the connector can cause a poor
connection or corrosion. Be sure not to allow water or foreign
material on the connector when disconnecting.
Do not damage the terminals.
2008 Mazda CX-9 Grand Touring
2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:29:30 AM
Page 33
© 2005 Mitchell Repair Information Company, LLC.
2. Remove the air cleaner component. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION
[MZI-3.7] .)
3. Remove the TCM. (See TCM REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL].)
4. Verify that there is no continuity between coupler component terminals B1, B3, B4, B9, B10, B11, B14,
B17, B18, B21, B22 and GND.
If there is any malfunction, inspect the coupler component.
If the coupler component is normal, replace the control valve body. (See CONTROL VALVE
BODY REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL].)
5. Install the TCM. (See TCM REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL].)
6. Install the air cleaner component. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZI-
3.7] .)
7. Connect the negative battery cable.
TCM INSPECTION [AW6A-EL, AW6AX-EL]
TR SWITCH OPERATING INSPECTION
1. Verify that the starter operates only when the ignition switch is turned to the START position with the
selector lever in P or N position.
If there is any malfunction, neutral position learning. (See TCM REMOVAL/INSTALLATION
[AW6A-EL, AW6AX-EL].)
2. Verify that the back-up lights illuminate when shifted to R position with the ignition switch at the ON
position.
If there is any malfunction, neutral position learning. (See TCM REMOVAL/INSTALLATION
[AW6A-EL, AW6AX-EL].)
3. Verify that the positions of the selector lever and the indicator light correspond.
If there is any malfunction, perform the neutral position learning. (See TCM
REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL].)
4. Verify that the TR PID is normal.
If there is any malfunction, perform the neutral position learning. (See TCM
REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL].)
2008 Mazda CX-9 Grand Touring
2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:29:30 AM
Page 34
© 2005 Mitchell Repair Information Company, LLC.
Fig. 36: Identifying Selector Indicator Light
Courtesy of MAZDA MOTORS CORP.
CONTROL MODULE INSPECTION
1. Remove the air cleaner component. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION
[MZI-3.7] .)
2. Measure the voltage at each TCM connector (wiring harness-side) terminal and refer to the TERMINAL
VOLTAGE TABLE.
If the voltage is not as specified in the Terminal Voltage Table (Reference), inspect the parts under
"Inspection item (s)".
Terminal Voltage Table (Reference)
Fig. 37: Identifying TCM Short Cord Connector Terminal (TCM Side)
Courtesy of MAZDA MOTORS CORP.
VOLTAGE SPECIFICATION
WARNING:
Be careful not to damage the connector waterproofing when
measuring the TCM terminal voltage. If damaged, the
waterproofing efficiency could be negatively affected.
NOTE:
Use the ground of terminal A9 of the TCM connector (wiring harness-
side) when measuring terminal voltage, as an error may occur when
connecting the negative circuit tester to ground.
Terminal
Signal
Connected
to
Test condition
Voltage
(V)
Inspection item (s)
A1
Battery back
up supply
Battery
Constant
B+
Inspect battery
Inspect related
harness
Below
Inspect selector lever
component (See
2008 Mazda CX-9 Grand Touring
2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:29:30 AM
Page 35
© 2005 Mitchell Repair Information Company, LLC.
A3
Up switch
(Selector
lever
component)
Up switch
(Selector
lever
component)
Shift up (M range)
1.0
SELECTOR
LEVER
COMPONENT
INSPECTION )
Inspect related
harness
Other ranges, all positions B+
A4
Down switch
(Selector
lever
component)
Down switch
(Selector
lever
component)
Shift down (M range)
Below
1.0
Inspect selector lever
component (See
SELECTOR
LEVER
COMPONENT
INSPECTION )
Inspect related
harness
Other ranges, all positions B+
A5
Starter lock
output signal
PCM
Shift the
selector lever
to P or N
position.
Ignition
switch ON
B+
Inspect PCM
Inspect related
harness
Ignition
switch OFF
Below
1.0
A6
CAN_L
PCM
Because this terminal is for
serial communication,
good/no good judgment by
terminal voltage is not
possible. Carry out
inspection according to
DTCs.
-
Inspect related
harness
A7
M range
switch
M range
switch
M range
Below
1.0
Inspect selector lever
component (See
SELECTOR
LEVER
COMPONENT
INSPECTION )
Inspect related
harness
Other positions, all ranges B+
A11
Power supply
Ignition
switch
Ignition switch ON
B+
Inspect Ignition
switch
Inspect related
harness
Ignition switch OFF
Below
1.0
A13
Back-up light
relay
Back-up light
relay
Ignition
switch ON
Shift the
selector
lever to R
position.
Below
1.0
Inspect back-up light
relay (See RELAY
INSPECTION )
Inspect related
harness
Other
B+
Because this terminal is for
2008 Mazda CX-9 Grand Touring
2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:29:30 AM
Page 36
© 2005 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст