Mazda CX-9 Grand Touring. Manual — part 322
available?
No
Go to the next step.
3
VERIFY RELATED PENDING CODE
OR STORED DTCs
Turn the ignition switch off then to
the ON position (Engine off).
Verify the related PENDING CODE
or stored DTCs using the M-MDS.
Yes
Go to the appropriate DTC troubleshooting.(See
DTC TABLE [MZI-3.7].)
No
Go to the next step
4
INSPECT THE PERFORMANCE OF
THE PROCESSOR
Turn the ignition switch off.
Disconnect the battery and wait for 1
min.
Connect the battery.
Start the engine and warm it up
completely.
Allow the engine idle to stabilize.
Access FTP PID.
Is the pressure equal to 0 kPa {0
kgf/cm
2
, 2.0 psi}.
Yes Go to Step 6.
No
Go to the next step.
5
INSPECT FOR SELF-TEST DTC P260F
Idle the engine 2 min.
Perform the KOEO/KOER self-test.
Is DTC P260F present?
Yes Go to the next step.
No
Troubleshooting completed.
6
INSPECT PCM FOR THE LATEST
CALIBRATION
Program the PCM to the latest
calibration.
Turn the ignition switch to the ON
position (Engine running).
Idle the engine for 2 min.
Perform the KOEO/KOER self-test.
Is DTC P260F present?
Yes Go to the next step.
No
Troubleshooting completed.
INSPECT FOR CORRECT PCM
OPERATION
Disconnect all the PCM connectors.
Visually inspect for:
Pushed out pins
Yes Go to the next step.
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:44 AM
Page 421
© 2005 Mitchell Repair Information Company, LLC.
7
Corrosion
Connect all the PCM connectors and
verify that they seat correctly.
Retrieve DTCs using the M-MDS.
Is the PENDING CODE for this DTC
present?
No
The system is correctly. Go to the next step.
8
VERIFY TROUBLESHOOTING OF
DTC P260F HAS BEEN COMPLETED
Verify that all disconnected
connectors reconnected.
Clear the DTC from the PCM
memory using the M-MDS.
Perform the KOEO or KOER self-test
using the M-MDS.
(See KOEO/KOER SELF TEST
[MZI-3.7].)
Is the PENDING CODE for the DTC
present?
Yes
Replace the PCM, then go to the next step. (See
PCM REMOVAL/INSTALLATION [MZI-
3.7] .)
No
Go to the next step.
9
VERIFY AFTER REPAIR
PROCEDURE
Perform "AFTER REPAIR
PROCEDURE". (See AFTER
REPAIR PROCEDURE [MZI-
3.7].)
Are any DTCs present?
Yes
Go to the applicable DTC inspection. (See DTC
TABLE [MZI-3.7].)
No
Troubleshooting completed.
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:44 AM
Page 422
© 2005 Mitchell Repair Information Company, LLC.
2008 ENGINE
Service Tools (MZI-3.7) - Mazda CX-9
ENGINE SST [MZI-3.7]
1. Mazda SST number
2. Global SST number
Example
Fig. 1: Identifying Service Tools (1 Of 2)
Courtesy of MAZDA MOTORS CORP.
2008 Mazda CX-9 Grand Touring
2008 ENGINE Service Tools (MZI-3.7) - Mazda CX-9
2008 Mazda CX-9 Grand Touring
2008 ENGINE Service Tools (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:02:35 AM
Page 1
© 2005 Mitchell Repair Information Company, LLC.
Microsoft
Sunday, November 15, 2009 10:02:41 AM
Page 1
© 2005 Mitchell Repair Information Company, LLC.
Fig. 2: Identifying Service Tools (2 Of 2)
Courtesy of MAZDA MOTORS CORP.
2008 Mazda CX-9 Grand Touring
2008 ENGINE Service Tools (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:02:35 AM
Page 2
© 2005 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст