Mazda CX-9 Grand Touring. Manual — part 209
Open circuit
If there is no continuity, the circuit is open. Repair or replace the wiring harness.
MAF/IAT sensor terminal A and main relay No.1 terminal D
MAF/IAT sensor terminal C and PCM terminal 1AJ
MAF/IAT sensor terminal D and PCM terminal 1 AN
MAF/IAT sensor terminal E and PCM terminal 1AL
Short circuit
If there is continuity, the circuit is shorted. Repair or replace the wiring harness.
MAF/IAT sensor terminal A and body ground
MAF/IAT sensor terminal C and power supply
MAF/IAT sensor terminal C and body ground
MAF/IAT sensor terminal D and power supply
MAF/IAT sensor terminal D and body ground
MAF/IAT sensor terminal E and power supply
INTAKE AIR TEMPERATURE (IAT) SENSOR INSPECTION [MZI-3.7]
RESISTANCE INSPECTION
1. Disconnect the MAF/IAT sensor connector.
2. Measure the resistance between MAF/IAT sensor terminals A and F.
Fig. 12: Identifying MAF/IAT Sensor Terminals
Courtesy of MAZDA MOTORS CORP.
If not within the specification, replace the MAF/IAT sensor. (See MASS AIR FLOW
(MAF)/INTAKE AIR TEMPERATURE (IAT) SENSOR REMOVAL/INSTALLATION
NOTE:
Before performing the following inspection, make sure to follow the
procedure as indicated in the troubleshooting flowchart. (See HOW TO
USE THIS MANUAL .)
2008 Mazda CX-9 Grand Touring
2008 ENGINE Control System (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:07:19 AM
Page 15
© 2005 Mitchell Repair Information Company, LLC.
[MZI-3.7].)
If the monitor item status/specification (reference) is not within the specification, even though the
resistance is within the specification, perform the "Circuit Open/Short Inspection".
IAT sensor resistance
IAT SENSOR RESISTANCE SPECIFICATION CHART
IAT sensor characteristics graph (reference)
Fig. 13: Temperature Vs Resistance Graph
Courtesy of MAZDA MOTORS CORP.
CIRCUIT OPEN/SHORT INSPECTION
IAT (°C {°F}) Resistance (kilohm)
10(50}
Approx. 58.75
20 {68}
Approx. 37.30
30 {86}
Approx. 24.27
60 {140}
Approx. 7.70
2008 Mazda CX-9 Grand Touring
2008 ENGINE Control System (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:07:19 AM
Page 16
© 2005 Mitchell Repair Information Company, LLC.
Fig. 14: Identifying MAF/IAT Sensor Connector And PCM Wiring Harness Side Connector
Courtesy of MAZDA MOTORS CORP.
1. Disconnect the PCM connector. (See PCM REMOVAL/INSTALLATION [MZI-3.7].)
2. Inspect the following wiring harnesses for open or short. (Continuity inspection)
Open circuit
If there is no continuity, the circuit is open. Repair or replace the wiring harness.
MAF/IAT sensor terminal B and body ground
MAF/IAT sensor terminal F and PCM terminal 1AF
Short circuit
If there is continuity, the circuit is shorted. Repair or replace the wiring harness.
MAF/IAT sensor terminal B and power supply
MAF/IAT sensor terminal F and body ground
MAF/IAT sensor terminal F and power supply
THROTTLE POSITION (TP) SENSOR INSPECTION [MZI-3.7]
2008 Mazda CX-9 Grand Touring
2008 ENGINE Control System (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:07:19 AM
Page 17
© 2005 Mitchell Repair Information Company, LLC.
VOLTAGE INSPECTION
1. Verify that no DTC related to APP sensor has been detected.
If any DTCs related to APP sensor have been detected, perform the DTC inspection. (See DTC
TABLE [MZI-3.7] .)
2. Connect the M-MDS to the DLC-2.
3. Turn the ignition switch to the ON position.
4. Select TP1 or TP2 PID (voltage) on the M-MDS.
Fig. 15: Identifying DLC-2 Connector
Courtesy of MAZDA MOTORS CORP.
5. Operate the accelerator pedal and verify that the TP1 or TP2 PID (voltage) changes as shown in the
following graph.
If not verified, perform the "Circuit Open/Short Inspection".
If there is no open or short circuit, replace the throttle body. (See INTAKE-AIR SYSTEM
REMOVAL/INSTALLATION [MZI-3.7] .)
Fig. 16: Throttle Angle & Voltage Graph (Degrees)
NOTE:
Before performing the following inspection, make sure to follow the
procedure as indicated in the troubleshooting flowchart. (See HOW TO
USE THIS MANUAL .)
2008 Mazda CX-9 Grand Touring
2008 ENGINE Control System (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:07:19 AM
Page 18
© 2005 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст