Mazda CX-9 Grand Touring. Manual — part 210
Courtesy of MAZDA MOTORS CORP.
CIRCUIT OPEN/SHORT INSPECTION
Fig. 17: Throttle Body Wiring Harness Side Connector & PCM Wiring Harness Side-Connector
Courtesy of MAZDA MOTORS CORP.
1. Disconnect the PCM connector. (See PCM REMOVAL/INSTALLATION [MZI-3.7].
2. Inspect the following wiring harnesses for open or short circuit. (Continuity inspection)
Open circuit
If there is no continuity, there is an open circuit. Repair or replace the wiring harness.
Throttle body terminal C and PCM terminal 2AD
Throttle body terminal D and PCM terminal 2D
Throttle body terminal E and PCM terminal 2AH
Throttle body terminal F and PCM terminal 2Z
Short circuit
2008 Mazda CX-9 Grand Touring
2008 ENGINE Control System (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:07:19 AM
Page 19
© 2005 Mitchell Repair Information Company, LLC.
If there is continuity, there is a short circuit. Repair or replace the wiring harness.
Throttle body terminal C and power supply
Throttle body terminal C and body ground
Throttle body terminal D and body ground
Throttle body terminal E and power supply
Throttle body terminal F and body ground
Throttle body terminal F and power supply
ACCELERATOR PEDAL POSITION (APP) SENSOR INSPECTION [MZI-3.7]
VOLTAGE INSPECTION
1. Turn the ignition switch to the ON position (Engine OFF).
2. Verify that the PCM terminal 1 AC, 1 AG and 1 AK change smoothly while throttle valve is gradually
opened.
If as verified, go to next step.
If not as verified, perform the "Circuit Open/Short Inspection".
If there is no open or short circuit, replace the throttle body.
3. Verify that the PCM terminal 1 AC, 1 AG and 1 AK voltages are as shown in the following table.
Fig. 18: Identifying PCM Wiring Harness Side-Connector
Courtesy of MAZDA MOTORS CORP.
NOTE:
Before performing the following inspection, make sure to follow the
procedure as indicated in the troubleshooting flowchart. (See HOW TO
USE THIS MANUAL .)
2008 Mazda CX-9 Grand Touring
2008 ENGINE Control System (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:07:19 AM
Page 20
© 2005 Mitchell Repair Information Company, LLC.
If voltage is not as following table, perform the "Circuit Open/Short Inspection".
If there is no open or short circuit, replace accelerator pedal. (See ACCELERATOR
PEDAL REMOVAL/INSTALLATION [MZI-3.7] .)
APP sensor output voltage
APP SENSOR OUTPUT VOLTAGE SPECIFICATION CHART
CIRCUIT OPEN/SHORT INSPECTION
Fig. 19: Identifying Accelerator Pedal Position Sensor & PCM Wiring Harness Side Connector
Courtesy of MAZDA MOTORS CORP.
1. Disconnect the PCM connector. (See PCM REMOVAL/INSTALLATION [MZI-3.7].
2. Inspect the following wiring harnesses for open or short circuit. (Continuity inspection)
Condition
PCM terminal 1AK (APP
sensor No.1)
PCM terminal 1AG (APP
sensor No.2)
PCM terminal 1 AC
(APP sensor No.3)
Accelerator pedal
released
Approx. 4.1 V
Approx. 1.5 V
Approx. 0.1 V
Accelerator pedal
depressed
Approx. 1.0 V
Approx. 3.9 V
Approx. 3.3 V
2008 Mazda CX-9 Grand Touring
2008 ENGINE Control System (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:07:19 AM
Page 21
© 2005 Mitchell Repair Information Company, LLC.
Open circuit
If there is no continuity, there is an open circuit. Repair or replace the wiring harness.
APP sensor terminal B and PCM terminal 1 AC
APP sensor terminal C and PCM terminal 1AH
APP sensor terminal D and PCM terminal 1Y
APP sensor terminal E and PCM terminal 1AK
APP sensor terminal F and PCM terminal 1BA
APP sensor terminal G and PCM terminal 1AD
Short circuit
If there is continuity, there is a short circuit. Repair or replace the wiring harness.
APP sensor terminal B and body ground
APP sensor terminal B and power supply
APP sensor terminal C and power supply
APP sensor terminal D and body ground
APP sensor terminal E and body ground
APP sensor terminal E and power supply
APP sensor terminal F and body ground
APP sensor terminal G and power supply
CRANKSHAFT POSITION (CKP) SENSOR REMOVAL/INSTALLATION [MZI-
3.7]
NOTE:
Disconnect the connector after the CKP sensor is removed to prevent the
CKP sensor from falling off.
The bolt and sensor are integrated and cannot be pulled out.
When removing the CKP sensor, be careful not to drop the tool.
The bolt and sensor must be pulled in different directions. Pull them as
indicated in the figure.
Fig. 20: Identifying CKP Sensor
2008 Mazda CX-9 Grand Touring
2008 ENGINE Control System (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:07:19 AM
Page 22
© 2005 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст