Mazda CX-9 Grand Touring. Manual — part 297
DTC P1285, P1299 [MZI-3.7]
DTC P1285, P1299 (MZI-3.7) DETECTION CONDITIONS AND POSSIBLE CAUSES
DIAGNOSTIC PROCEDURE
DTC P1285, P1299 (MZI-3.7) DIAGNOSTIC PROCEDURE
Clear the DTC from the PCM
memory using the M-MDS.
Start the engine and run it at idle.
Retrieve DTCs using the M-MDS.
Is the PENDING CODE for this
DTC present?
No
Go to the next step.
7
VERIFY AFTER REPAIR
PROCEDURE
Perform "AFTER REPAIR
PROCEDURE". (See AFTER
REPAIR PROCEDURE [MZI-
3.7].)
Are any DTC present?
Yes
Go to the applicable DTC inspection. (See DTC
TABLE [MZI-3.7].)
No
Troubleshooting completed.
DTC P1285
P1285: Cylinder head over temperature condition
DCT P1299
P1299: Cylinder head over temperature protection active
DETECTION
CONDITION
P1285 indicates that an engine overheat condition was sensed by the
CHT sensor.
P1299 indicates that an engine overheat condition was detected by the
CHT sensor.
Fail-safe function was activated to cool the engine.
POSSIBLE CAUSE
Low engine coolant level
Base engine malfunction
Engine cooling system malfunction
CHT sensor malfunction
STEP
INSPECTION
ACTION
1
VERIFY FREEZE FRAME DATA HAS BEEN
RECORDED
Has FREEZE FRAME DATA been recorded?
Yes Go to the next step.
No
Record FREEZE FRAME DATA on
the repair order, then go to the next
step.
2
VERIFY RELATED REPAIR INFORMATION
AVAILABILITY
Verify related Service Bulletins and/or on-line
Yes
Perform repair or diagnosis according
to the available Service Bulletins.
If the vehicle is not repaired, go
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:40 AM
Page 321
© 2005 Mitchell Repair Information Company, LLC.
repair information availability.
Is any related Service Bulletins available?
to the next step.
No
Go to the next step.
3
INSPECT COOLING SYSTEM
An engine overheat condition is sensed by the
CHT sensor.
Check the cooling system for:
Correct coolant level
Internal or external coolant leaks
Blockage of the radiator
Cooling fan operation
Is the cooling system normal?
WARNING:
Never remove the cooling system cap or
loosen the radiator drain plug while the
engine is running, or when the engine and
radiator are hot. Scalding engine coolant
and steam may shoot out and cause serious
injury. It may also damage the engine and
cooling system.
Turn off the engine and wait until it is cool.
Even then, be very careful when removing
the cap. Wrap a thick cloth around it and
slowly turn it counterclockwise to the first
stop. Step back while the pressure escapes.
When you are sure all the pressure is gone,
press down on the cap using the cloth, turn
it, and remove it.
NOTE:
If the electric cooling fan does not operate,
go to the applicable DTC inspection. (See
DTC TABLE [MZI-3.7].)
Yes Go to the next step.
No
Repair if necessary. Then go to the next
step.
4
INSPECT OPERATION OF THE CHT SENSOR
Run the engine until the engine temperature
stabilizes.
Verify the radiator hoses are hot and the
cooling system is pressurized.
Verify self-test DTCs.
Is DTC P1285 present?
Yes Go to the next step.
No
An engine overheat temperature was
not detected. Repair any other DTCs if
necessary.
INSPECT CHT SENSOR
Replace the CHT sensor, then go to the
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:41 AM
Page 322
© 2005 Mitchell Repair Information Company, LLC.
DTC P1288 [MZI-3.7]
DTC P1288 (MZI-3.7) DETECTION CONDITIONS AND POSSIBLE CAUSES
DIAGNOSTIC PROCEDURE
DTC P1288 (MZI-3.7) DIAGNOSTIC PROCEDURE
5
Inspect the CHT sensor. (See CYLINDER
HEAD TEMPERATURE (CHT) SENSOR
INSPECTION [MZI-3.7] .)
Is there any malfunction?
Yes next step.
No
Go to the next step.
6
VERIFY TROUBLESHOOTING OF DTC P1285,
P1299 HAS BEEN COMPLETED
Verify that all disconnected connectors are
reconnected.
Turn the ignition switch to the ON position
(Engine off).
Clear the DTC from the PCM memory using
the M-MDS.
Start the engine and run it at idle.
Retrieve DTCs using the M-MDS.
Is the PENDING CODE for this DTC present?
Yes
Replace the PCM, then go to the next
step. (See PCM
REMOVAL/INSTALLATION [MZI-
3.7] .)
No
Go to the next step.
7
VERIFY AFTER REPAIR PROCEDURE
Perform the "AFTER REPAIR
PROCEDURE". (See AFTER REPAIR
PROCEDURE [MZI-3.7].)
Are any DTC present?
Yes
Go to the applicable DTC inspection.
(See DTC TABLE [MZI-3.7].)
No
Troubleshooting completed.
DTC P1288
CHT sensor out of self-test range
DETECTION
CONDITION
Indicates the CHT sensor is out of self-test range. The engine is not at a
normal operating temperature.
POSSIBLE CAUSE
Cold engine
Engine overheating
Connector or terminal malfunction
Low engine coolant level
CHT sensor malfunction
STEP
INSPECTION
ACTION
VERIFY FREEZE FRAME DATA HAS
BEEN RECORDED
Yes Go to next step.
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:41 AM
Page 323
© 2005 Mitchell Repair Information Company, LLC.
1
Has FREEZE FRAME DATA been
recorded?
No
Record FREEZE FRAME DATA on the repair
order, then go to next step.
2
VERIFY RELATED REPAIR
INFORMATION AVAILABILITY
Verify related Service Bulletins
availability.
Is any related Service Bulletins
available?
Yes
Perform repair or diagnosis according to
available Service Bulletins.
If vehicle is not repaired, go to next step.
No
Go to next step.
3
VERIFY RELATED PENDING CODE OR
STORED DTC
Verify the related PENDING CODE or
stored DTCs.
Are other DTCs present?
Yes
Go to appropriate DTC inspection. (See DTC
TABLE [MZI-3.7].)
No
Go to the next step.
4
INSPECT THE COOLING SYSTEM
Inspect the vehicle coolant level.
Is the cooling system normal?
Yes Go to the next step.
No
Inspect the cooling system (overheat), the go
to Step 7.
5
INSPECT CHT SENSOR
Inspect the CHT sensor. (See
CYLINDER HEAD
TEMPERATURE (CHT) SENSOR
INSPECTION [MZI-3.7] .)
Is there any malfunction?
Yes Replace the CHT sensor, then go to Step 7.
No
Go to the next step.
6
INSPECT FOR CORRECT PCM
OPERATION
Disconnect all the PCM connectors.
Visually inspect for:
Pushed out pins
Corrosion
Connect all the PCM connectors and
verify that they seat correctly.
Retrieve DTCs using the M-MDS.
Is the PENDING CODE for this DTC
present?
Yes Go to the next step.
No
The system is correctly. Go to the next step.
VERIFY TROUBLESHOOTING OF DTC
P1288 HAS BEEN COMPLETED
Verify that all disconnected connectors
reconnected.
Yes
Replace the PCM, then go to the next step.
(See PCM REMOVAL/INSTALLATION
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:08:41 AM
Page 324
© 2005 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст