Mazda CX-9 Grand Touring. Manual — part 201
1. Disconnect the negative battery cable. (See BATTERY REMOVAL/INSTALLATION [MZI-3.7] .)
2. Remove in the order indicated in the table.
Fig. 13: Identifying Purge Solenoid Valve & Torque Specifications
Courtesy of MAZDA MOTORS CORP.
3. Install in the reverse order of removal.
PURGE SOLENOID VALVE INSPECTION [MZI-3.7]
AIRFLOW INSPECTION
1. Disconnect the negative battery cable. (See BATTERY REMOVAL/INSTALLATION [MZI-3.7] .)
2. Disconnect the quick release connector from the purge solenoid valve. (See QUICK RELEASE
CONNECTOR (EMISSION SYSTEM) REMOVAL/INSTALLATION [MZI-3.7].)
3. Remove the purge solenoid valve. (See PURGE SOLENOID VALVE REMOVAL/INSTALLATION
[MZI-3.7].)
4. Verify that the airflow is as indicated in the table.
If as specified in the table, perform the "Circuit Open/Short Inspection".
If not as specified in the table, inspect the purge solenoid valve.
CONTINUITY CHART
Measured condition
Continuity between A-B
When voltage is not applied between terminals A and B
No airflow
When voltage is applied between terminals A and B
Airflow detected
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE Emission System (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:04:04 AM
Page 11
© 2005 Mitchell Repair Information Company, LLC.
Fig. 14: Identifying Purge Solenoid Valve Connector
Courtesy of MAZDA MOTORS CORP.
CIRCUIT OPEN/SHORT INSPECTION
1. Disconnect the PCM connector.
2. Inspect the following wiring harness for an open or short circuit (continuity check).
Fig. 15: Identifying Purge Solenoid Valve Wiring Harness-Side Connector
Courtesy of MAZDA MOTORS CORP.
Fig. 16: Identifying PCM Wiring Harness-Side Connector
Courtesy of MAZDA MOTORS CORP.
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE Emission System (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:04:04 AM
Page 12
© 2005 Mitchell Repair Information Company, LLC.
Fig. 17: Identifying PCV Valve Heater Control
Courtesy of MAZDA MOTORS CORP.
Open circuit
If there is no continuity, the circuit is open. Repair or replace the harness.
Purge solenoid valve terminal A and main relay No.1 terminal D
Purge solenoid valve terminal B and PCM terminal 1 BC
Short circuit
If there is continuity, the circuit is short. Repair or replace the harness.
Purge solenoid valve terminal A and power supply
Purge solenoid valve terminal A and body ground
Purge solenoid valve terminal B and power supply
Purge solenoid valve terminal B and body ground
POSITIVE CRANKCASE VENTILATION (PCV) VALVE INSPECTION [MZI-3.7]
AIRFLOW INSPECTION
1. Disconnect the negative battery cable. (See BATTERY REMOVAL/INSTALLATION [MZI-3.7] .)
2. Disconnect the PCV valve hose from the PCV valve. (See POSITIVE CRANKCASE VENTILATION
(PCV) VALVE REMOVAL/INSTALLATION [MZI-3.7].)
3. Verify that there is no airflow when pressure is applied to the PCV valve using a vacuum pump.
NOTE:
The PCV valve cannot be reassembled once it is removed because the
tabs will have been broken. Inspect the PCV valve without removing it
from the vehicle.
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE Emission System (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:04:04 AM
Page 13
© 2005 Mitchell Repair Information Company, LLC.
If there is airflow, replace the PCV valve. (See POSITIVE CRANKCASE VENTILATION
(PCV) VALVE REMOVAL/INSTALLATION [MZI-3.7].)
4. Verify that there is airflow when vacuum is applied to the PCV valve.
If there is no airflow, replace the PCV valve. (See POSITIVE CRANKCASE VENTILATION
(PCV) VALVE REMOVAL/INSTALLATION [MZI-3.7].)
RESISTANCE INSPECTION
1. Disconnect the negative battery cable. (See BATTERY REMOVAL/INSTALLATION [MZI-3.7] .)
2. Remove the engine cover. (See ENGINE COVER REMOVAL/INSTALLATION [MZI-3.7] .)
3. Disconnect the PCV valve heater control connector.
4. Measure the resistance between the PCV valve heater control terminals.
If within the specification, perform out the "Circuit Open/Short Inspection".
If not within the specification, replace the PCV valve. (See POSITIVE CRANKCASE
VENTILATION (PCV) VALVE REMOVAL/INSTALLATION [MZI-3.7].)
PCV valve heater control resistance 10-35 ohm
Fig. 18: Identifying PCV Valve Heater Control Connector Terminals
Courtesy of MAZDA MOTORS CORP.
CIRCUIT OPEN/SHORT INSPECTION
1. Disconnect the PCM connector.
2. Inspect the following wiring harnesses for open or short circuit (continuity check).
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE Emission System (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:04:04 AM
Page 14
© 2005 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст