Mazda CX-9 Grand Touring. Manual — part 202
Fig. 19: Identifying PCV Valve Heater Control Wiring Harness Side Connector
Courtesy of MAZDA MOTORS CORP.
Fig. 20: Identifying Fuse Box (Main Relay No.1)
Courtesy of MAZDA MOTORS CORP.
Fig. 21: Identifying PCM Wiring Harness Side Connector
Courtesy of MAZDA MOTORS CORP.
Open circuit
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE Emission System (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:04:04 AM
Page 15
© 2005 Mitchell Repair Information Company, LLC.
If there is no continuity, there is an open circuit. Repair or replace the wiring harness.
PCV valve heater control terminal A and main relay No.1 terminal D
PCV valve heater control terminal B and PCM terminal 2BL
Short circuit
If there is continuity, there is a short circuit. Repair or replace the wiring harness.
PCV valve heater control terminal A and power supply
PCV valve heater control terminal A and body ground
PCV valve heater control terminal B and power supply
PCV valve heater control terminal B and body ground
POSITIVE CRANKCASE VENTILATION (PCV) VALVE
REMOVAL/INSTALLATION [MZI-3.7]
1. Disconnect the negative battery cable. (See BATTERY REMOVAL/INSTALLATION [MZI-3.7] .)
2. Remove in the order indicated in the table.
CAUTION:
A new PCV valve must be installed if removed from the cylinder head
cover.
Upon removal, damage will occur to the locking mechanism on the
PCV valve.
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE Emission System (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:04:04 AM
Page 16
© 2005 Mitchell Repair Information Company, LLC.
Fig. 22: Identifying PCV Valve Hose, PCV Valve Heater Control Connector, PCV Valve And O-
Ring
Courtesy of MAZDA MOTORS CORP.
3. Install in the reverse order of removal.
POSITIVE CRANKCASE VENTILATION (PCV) VALVE HEATER FITTING
INSPECTION [MZI-3.7]
RESISTANCE INSPECTION
1. Disconnect the negative battery cable. (See BATTERY REMOVAL/INSTALLATION [MZI-3.7] .)
2. Disconnect the PCV valve heater fitting connector.
3. Measure the resistance between the PCV valve terminals.
If within the specification, perform out the "Circuit Open/Short Inspection".
If not within the specification, replace the PCV valve heater fitting. (See POSITIVE
CRANKCASE VENTILATION (PCV) VALVE HEATER FITTING
REMOVAL/INSTALLATION [MZI-3.7].)
PCV valve heater fitting resistance 10-35 ohms
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE Emission System (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:04:04 AM
Page 17
© 2005 Mitchell Repair Information Company, LLC.
Fig. 23: Identifying PCV Valve Heater Connector Terminal
Courtesy of MAZDA MOTORS CORP.
CIRCUIT OPEN/SHORT INSPECTION
1. Disconnect the PCM connector.
2. Inspect the following wiring harnesses for open or short circuit (continuity check).
Fig. 24: Identifying PCV Valve Heater Control Wiring Harness Side Connector
Courtesy of MAZDA MOTORS CORP.
Fig. 25: Identifying Fuse Box (Main Relay No.1)
Courtesy of MAZDA MOTORS CORP.
2008 Mazda CX-9 Grand Touring
2008 ENGINE PERFORMANCE Emission System (MZI-3.7) - Mazda CX-9
Microsoft
Sunday, November 15, 2009 10:04:04 AM
Page 18
© 2005 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст